Related Topics
-
What are the components of a force? -
What would be the speed of the ball when caught in the absence of air resistance if the ball is thrown upwards and caught when it comes back down? -
How far will the stone have fallen after 10 seconds if a stone is dropped from a flying helicopter, ignoring the air resistance? -
What type of bearing is used for landing gear wheel? -
When inspecting the gear teeth on the helical input pinion gear, the tooth contact pattern is found to be too high. This condition will -
Which of the following hydraulic fluid is colored red? -
Which one of the following fit has the largest interference? -
Which of the following types of fit has the biggest positive allowance? -
Which of the following compression spring will transfer the maximum load? -
Which one of the following materials is non-ferrous?
1. How many revolutions of the crank shaft are in a complete cycle for a 4-stroke-cycle engine?
A. 1
B. 2
C. 3
D. 4
Questions: 9 | Attempts: 10
-
Sample QuestionHow many revolutions of the crank shaft are in a complete cycle for a 2-stroke-cycle engine?
Questions: 15 | Attempts: 11
-
Sample QuestionIf two forces F1 = 120 N and F2=80 N are acting at a point making an angle of 55°between them. Find the resultant of these forces in magnitude.
Answer all questions. These should test to see if you have read the material.
Questions: 11 | Attempts: 49
-
Sample QuestionWhat is the definition of displacment?
Testing your knowledge of GW2 mechanics
Questions: 10 | Attempts: 1084
-
Sample QuestionDaze, has what effect on enemies? Also, does it stack duration or intensity?
Take this Quiz to test how thorough you are with the concepts of Mechanics!
All the Best!
Questions: 6 | Attempts: 36
-
Sample QuestionUsing a stop-watch, Tom measured the time for a motor car to pass through 2 streetlights. The reading was 1.2 s. If the reaction time of Tom is 0.2 s, what is the maximum possible percentage error of his measurement?
1. How many revolutions of the crank shaft are in a complete cycle for a 4-stroke-cycle engine?
A. 1
B. 2
C. 3
D. 4
Questions: 9 | Attempts: 19
-
Sample QuestionHow many revolutions of the crank shaft are in a complete cycle for a 2-stroke-cycle engine?
Chapter 2 terms
Questions: 4 | Attempts: 18
-
Sample QuestionThe idea that every object continues in its state of rest, or of uniform motion in a straight line, unless compelled to change that state by forces impressed upon is reflective of
M7 part 2do not share
Questions: 20 | Attempts: 376
-
Sample QuestionGreasing of bearing should be continued until:
M7 part 1Please do not share
Questions: 20 | Attempts: 430
-
Sample QuestionA set of wheel bearing requires grease remove and cleaning prior to inspection as acceptable cleaning method would be
This is a test on Work and Energy for NCEA Level 2 Physics in New Zealand
Questions: 10 | Attempts: 14
-
Sample QuestionCalaculate the work done when lifting a 20 kg mass 1.5m off a floor? (g = 10m/s2)
Quiz about units used in mechanics and motion graphs and constant acceleration equations
Questions: 10 | Attempts: 28
-
Sample QuestionHow many metres in one kilometre?
This quiz checks on your understanding of resolving vectors into its components.
Questions: 5 | Attempts: 154
This quiz checks on your understanding on the topic of vector.
Questions: 5 | Attempts: 325
-
Sample QuestionA vector is a quantity that has
Long before the means and technology were available there has been the
desire to manipulate the natural behavior of fluid flow....
Questions: 5 | Attempts: 16
-
Sample QuestionWho studied applied math at a University near the "Memphis Delta"?
Determine which phrases are correctly spelled, punctuated, and/or capitalized.
Questions: 48 | Attempts: 80
-
Sample QuestionWhich phrase is incorrect?
