Top ICND Quizzes & Trivia

An Interconnecting Cisco Networking Devices [ICSP] qualification is the first step towards achieving the CCNA Routing and Switching certification. The ICSP is associated with the CCENT qualification. It tests a candidate’s skills and knowledge about how to install, operate and troubleshoot a small office network. The course comes in two parts. The second focuses on topics such as IPv6, VLANs; determining IP routes, VTP, managing IP traffic with access lists, etc.

If you’re looking for your first IT professional certification then an ICSP qualification is what you need. It is a great opportunity to learn the latest networking skills. You’ll be at the forefront of modern technologies. It will establish you as a CISCO Certified Entry Network Technician. Do you think you have what it takes? Can you define the Djikstra Algorithm? What is the function of a router? Take these quizzes and see if you have the technological knowledge to gain an ICSP qualification.

ICND Questions and Answers

Which fields are found in both TCP and UDP segments? (Choose 2)

Reversed

Window

Reversed

Window

Destination Port

Checksum

Data

ICND question from

Could you pass this CCNA Technical exam?

Take Quiz
What protocol resolves MAC addresses to IP addresses?

DHCP

RARP

ARP

DNS

ICND question from

Could you pass this CCNA Technical exam?

Take Quiz
What command must be issued to configure frame relay encapsulation, given the requirement that there are multiple vendors involved?

Answer 2

Answer 3

Answer 5

ICND question from

Could you pass this CCNA Technical exam?

Take Quiz
Which three statements about networks are accurate?

Networks are used to transmit data in various environments, including homes, small businesses, and large enterprises.

A main office can have hundreds or even thousands of people who depend on network access to do their jobs.

A network is a connected collection of devices that can communicate with each other.

A main office usually has one large network to connect users

The purpose of a network is to create means to provide workers with access to all information and components that are accessible by the network.

Remote locations cannot connect to a main office through a network

ICND question from

Cisco CCNA ICND 1

Take Quiz
What is the purpose of a router?

To interconnect networks and choose the best paths between them.

To provide the connect points for media

to serve as the endpoint in the network, sending and receiving data

to provide the means by which the signals are transmitted from one network device to another

ICND question from

Cisco CCNA ICND 1

Take Quiz
What is the purpose of a switch?

to connect separate networks and filter the traffic over those networks so that the data is transmitted through the most efficient route

to choose the path over which data is sent to its destination

to serve as the endpoint in the the network, sending and receiving data

to provide network attachment to the end systems and intelligent switching of the data within the local network

ICND question from

Cisco CCNA ICND 1

Take Quiz
Which two statements about the functions of a hub are accurate? (Choose two.) (Source: Understanding the Challenges of Shared LANs)

A hub extends an Ethernet LAN.

A hub reduces the size of a collision domain

Adding a hub eliminates the need for users on a network segment to compete for the same bandwidth.

A hub is a data link layer device.

A hub amplifies the data signal before retransmitting it.

ICND question from

ICND Part 1 Vol 1 Module 2 Review

Take Quiz
Which three statements best describe collisions? (Choose three.) (Source: Understanding the Challenges of Shared LANs)

Collisions occur when two or more stations on a shared media transmit at the same time

Larger segments are less likely to have collisions.

In a collision, the frames are destroyed, and each station in the segment begins a random timer that must be completed before attempting to retransmit the data.

Adding a hub to a network can improve collision issues.

More segments on a network mean greater potential for collisions.

ICND question from

ICND Part 1 Vol 1 Module 2 Review

Take Quiz
Which of these choices best describes a collision domain? (Source: Understanding the Challenges of Shared LANs)

two or more devices trying to communicate at the same time

two networks that are connected

network segments that share the same bandwidth

none of the above

ICND question from

ICND Part 1 Vol 1 Module 2 Review

Take Quiz
Which feature is required for multiple VLANs to span multiple switches? (Source:Implementing VLANs and Trunks)

a trunk to connect the switches

a router to connect the switches

a bridge to connect the switches

a VLAN configured between the switches

ICND question from

ICND P2 V1 M2

Take Quiz
What does a VMPS map to VLAN assignments? (Source: Implementing VLANs and Trunks)

host IDs

usernames

IP addresses

MAC addresses

ICND question from

ICND P2 V1 M2

Take Quiz
What are two reasons for using 802.1Q? (Choose two.) (Source: Implementing VLANs and Trunks)

to allow switches to share a trunk link with nontrunking clients

to allow clients to see the 802.1Q header

to provide inter-VLAN communications over a bridge

to load-balance traffic between parallel links using STP

to provide trunking between Cisco switches and other vendor switches

ICND question from

ICND P2 V1 M2

Take Quiz

‹ ›

All Time Popular

ICND P2 V1 M2

ICND Part 2 Vol 1 Module 2

Questions: 31 | Attempts: 93

Sample Question
Which feature is required for multiple VLANs to span multiple switches? (Source:Implementing VLANs and Trunks)

A trunk to connect the switches

A router to connect the switches

A bridge to connect the switches

A VLAN configured between the switches

ICND Test

By IMS Asia (http://www.imsasia.com)

Questions: 30 | Attempts: 70

Sample Question
Which access level allows a person to see all the configurations, not just limited commands, and enter the configuration mode and may be password protected, it has the distinctive prompt “#”?

Exec user mode

Exec complete mode

No such mode exits

Exec privilege mode

ICND P2 V2 M5

ICND Part 2 Vol 2 Module 5

Questions: 7 | Attempts: 69

Sample Question
How do you minimize the bandwidth requirement for EIGRP packets? (Source:Implementing EIGRP)

By propagating only data packets

By propagating only hello packets

By propagating only routing table changes and hello packets

By propagating the entire routing table only to those routers that are affected by a topology change

ICND Part 1 Vol 1 Module 3 Review

Module 3 Review

Questions: 19 | Attempts: 61

ICND P2 V1 M4

ICND Part 2 Vol 1 Module 4

Questions: 8 | Attempts: 50

Sample Question
What are two characteristics of OSPF? (Choose two.) (Source: Implementing OSPF)

OSPF uses a two layer hierarchy.

OSPF is a proprietary routing protocol.

OSPF is an open standard.

OSPF is similar to the RIP routing protocol.

OSPF is a distance vector routing protocol.

ICND Part 1

Test review of First Module from ICND Pt1 Vol 1 Ver 1

Questions: 42 | Attempts: 45

Sample Question
Which three statements about networks are accurate? Choose three.)

Networks are used to transmit data in many kinds of environments, including homes, small businesses, and large enterprises.

A main office can have hundreds or even thousands of people who depend on network access to do their jobs.

A network is a connected collection of devices that can communicate with each other.

A main office usually has one large network to connect all users.

The purpose of a network is to create a means to provide all workers with access to all information and components that are accessible by the network. Remote locations cannot connect to a main office through a network.

ICND P2 V2 M6

ICND Part 2 Vol 2 Module 6

Questions: 13 | Attempts: 44

Sample Question
What does a Cisco router do with a packet when it matches an ACL permit statement?(Source: Introducing ACL Operation)

Discards the packet

Returns the packet to its originator

Sends the packet to the output buffer

Holds the packet for further processing

ICND P2 V1 M1

ICND Part 2 Vol 1 Module 1

Questions: 27 | Attempts: 34

Sample Question
Which access level allows a person to access all router commands and can be password protected to allow only authorized individuals to access the router? (Source: Introducing the Review Lab)

User EXEC level

Setup EXEC level

Enable EXEC level

Privileged EXEC level

Ccna ICND 1 Part 2

Questions: 125 | Attempts: 22

Sample Question
Which three of the following components are common to routers, switches, and Computers?

RAM

CPU

Motherboard

Keyboard

Incd1 - Pre-assessment Quiz

No specific score is required in order to be eligible to participate in ICND1. Rather, your responses will inform the trainer as to what areas to focus on during class.Important: As newcomers to networking, do NOT be discouraged...

Questions: 10 | Attempts: 19

Sample Question
A user starts their computer at the beginning of the day. After logging on to the network, the user immediately opens their web browser and accesses the company’s website at http://www.myco.com. Which two types of servers were contacted by the user’s computer after the browser was started if the user successfully connects to the web site? (Choose two answers.)

Web server

Secure Web Server

Database Server

DNS Server

Part 1 (ICND)

Cisco Interconnecting Cisco Networking Devices Part 1 (ICND)

Questions: 6 | Attempts: 9

Sample Question
Which three statements are true about the operation of a full-duplex Ethernet network?(Choose three.)

There are no collisions in full-duplex mode.

A dedicated switch port is required for each full-duplex node.

Ethernet hub ports are pre-configured for full-duplex mode.

In a full-duplex environment, the host network card must check for the availability of the network media before transmitting.

The host network card and the switch port must be capable of operating in full-duplex mode.

Top ICND Quizzes & Trivia

Related Topics

ICND Questions and Answers