2A852 CDC Volume 1
.
- 1.The total production effort and management of group maintenance functions are the responsibility of the
- A.
Wing commander
- B.
Group commander
- C.
Maintenance officer
- D.
Maintenance operations center
- 2.Who is the key individual who allocates the maintenance resources required to meet mission requirements?
- A.
Wing commander
- B.
Resource commander
- C.
Logistics commander
- D.
Maintenance commander
- 3.Who monitors new requirements for training, equipment authorizations, special tools, workspace, facilities, and manning?
- A.
Section chief
- B.
Squadron commander
- C.
Flight commander/chief
- D.
Maintenance officer/maintenance supervisor
- 4.What is the main responsibility of the flight commander/chief?
- A.
Maintenance production
- B.
Allocate maintenance resources
- C.
Management, supervision, and training of assigned personnel
- D.
Total production effort and management of group maintenance functions
- 5.Which of the following individuals manages the squadron’s cannibalization program?
- A.
Section chief
- B.
Flight line expediter
- C.
Flight commander/chief
- D.
Maintenance officer/maintenance superintendent
- 6.Who is responsible for making sure personnel and equipment are identified and prepared to meet deployment taskings?
- A.
Group commander
- B.
Quality assurance
- C.
Wing commander
- D.
Section chief
- 7.Whose role is it to increase reliability and maintainability of aircraft and support equipment?
- A.
Wing commander
- B.
Quality assurance
- C.
Weapons standardization
- D.
Maintenance operations center
- 8.The quality assurance program (QAP)
- A.
Provides feedback to the operations group commander
- B.
Maintains aircraft estimated time in commission (ETIC)
- C.
Determines aircraft and equipment condition and personnel proficiency
- D.
Monitors and reports the status of electronic countermeasure (ECM) and sensor pods
- 9.Aerospace ground equipment (AGE) flight services all AGE with the exception of
- A.
Light carts
- B.
Heater units
- C.
Nitrogen carts
- D.
Non-powered munitions trailers
- 10.What is not a section of the maintenance support flight?
- A.
Wheel and tire
- B.
Repair and Reclamation
- C.
Alternate Mission Equipment
- D.
Transient Aircraft Maintenance
- 11.Which flight in the maintenance squadron supports the field assistance support team for calibration (FASTCAL)?
- A.
Test, measurement, and diagnostic equipment (TMDE).
- B.
Armament maintenance
- C.
Accessory maintenance.
- D.
Avionics.
- 12.Which of the following publications contains broad, enduring guidance for preparing and employing Air Force resources to support national objectives?
- A.
Air Force doctrine documents
- B.
Operating instructions.
- C.
Mission directives.
- D.
Manuals.
- 13.Air Force manuals may be supplemented at
- A.
The Air Force and command level
- B.
The command level only
- C.
The Air Force level only
- D.
At any level
- 14.What are Air Force policy directives?
- A.
Directives that prescribe the mission, area or responsibility, organization, responsibilities, and command relationships of Air Force units
- B.
Orders of the Secretary of the Air Force approved in the Secretariat or the Air Staff and issued as departmental publications
- C.
Orders of the Secretary of the Air Force to initiate, govern, or regulate actions of conduct by Air Force activities at any level.
- D.
Guidance documents consisting of procedures that usually contain examples for performing standard tasks.
- 15.Orders of the Secretary of the Air Force that have been approved in the Secretariat or the Air Staff and issued as departmental publications are called
- A.
Mission directives
- B.
Air Force manuals
- C.
Air Force instructions
- D.
Air Force policy directives
- 16.Field commands may supplement any of the following publication types except
- A.
Pamphlets
- B.
Staff digests.
- C.
Air Force manuals.
- D.
Air Force instructions
- 17.Informational publications that guide, point out, or otherwise facilitate research are called
- A.
Indexes
- B.
Catalogs
- C.
Handbooks
- D.
Directories
- 18.Besides publishing bulletins (PB) and base or headquarters official bulletins, other types of bulletins
- A.
May be issued weekly.
- B.
May be issued monthly
- C.
Are not authorized at any time.
- D.
May be authorized at any time.
- 19.As a rule, display of temporary visual aids should be limited to
- A.
10 months or less
- B.
6 months or less
- C.
90 days or less
- D.
30 days or less
- 20.All of the following may be included on a bulletin board except
- A.
Important information
- B.
Classified information.
- C.
Unclassified information.
- D.
For Official Use Only information
- 21.The maintenance data collection (MDC) system provides equipment maintenance schedules and inventory information for maintenance requirements established on
- A.
A calendar basis.
- B.
An as needed basis.
- C.
A modification basis.
- D.
A non-productive basis.
- 22.What major command (MAJCOM) is designated as the overall logistics manager for Air Force systems and equipment?
- A.
Air Combat Command (ACC).
- B.
Air Mobility Command (AMC).
- C.
Air Force Material Command (AFMC).
- D.
Air Education and Training Command (AETC).
- 23.Maintenance data collection (MDC) information is used as a tool for determining or validating manpower, budget, and
- A.
Equipment requirements
- B.
Computer requirements
- C.
Medical requirements
- D.
Dorm requirements
- 24.The first five digits of a job control number (JCN) indicate the
- A.
Year and Julian date.
- B.
Month and Julian date.
- C.
Equipment part number.
- D.
Equipment serial number
- 25.The reliability and maintainability information system (REMIS) is designed to accumulate data and provide the information necessary to support the
- A.
Department of Defense maintenance program.
- B.
Air Force equipment maintenance program.
- C.
Air Force flight test program
- D.
Defense data network.
Back to top