Welder Practice Interprovincial Red Seal Exam Quiz

Approved & Edited by ProProfs Editorial Team
The editorial team at ProProfs Quizzes consists of a select group of subject experts, trivia writers, and quiz masters who have authored over 10,000 quizzes taken by more than 100 million users. This team includes our in-house seasoned quiz moderators and subject matter experts. Our editorial experts, spread across the world, are rigorously trained using our comprehensive guidelines to ensure that you receive the highest quality quizzes.
Learn about Our Editorial Process
| By Cdjones
C
Cdjones
Community Contributor
Quizzes Created: 1 | Total Attempts: 1,455
Questions: 10 | Attempts: 1,455

SettingsSettingsSettings
Welder Practice Interprovincial Red Seal Exam Quiz - Quiz

Disclaimer: This is NOT an Interprovincial Standards (Red Seal) Examination. This is a practice examination that has been developed using similar weighting, question distribution, question taxonomies and question styles to that of a red seal examination. Success on this examination will NOT result in certification or qualification. This examination is intended to be used for self assessment in preparation for attempting a red seal examination. More information about the standard that the red seal examination is based may be found within the National Occupational Analysis for the occupation at www. Red-seal. Ca.


Questions and Answers
  • 1. 

    What does 3F designate on a welding specification sheet?

    • A.

      Answer Option 1

    • B.

      Answer Option 1

    • C.

      Answer Option 1

    • D.

      Answer Option 1

    Correct Answer
    A. Answer Option 1
  • 2. 

    With the scale of a drawing at 1:5, what is the length of line on the drawing for a plate length of 150cm (59”)?

    • A.

      Answer Option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer Option 1
  • 3. 

    How many millimeters is equivalent in length to 6 feet – 3 1/2 inches? (25.4mm = 1”)

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
  • 4. 

    Which type of drawing would show all three sides equally and uses horizontal plane lines at 30 degrees?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
    Explanation
    Answer option 1 is the correct answer because a drawing that shows all three sides equally and uses horizontal plane lines at 30 degrees would be an isometric drawing. In an isometric drawing, the object is represented with horizontal lines at 30 degrees to the horizontal plane, which creates an illusion of depth and shows all three sides of the object equally.

    Rate this question:

  • 5. 

    Which metal is more likely to crack due to weld joint shrinkage?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
    Explanation
    The metal that is more likely to crack due to weld joint shrinkage is Answer option 1.

    Rate this question:

  • 6. 

    What type of material has a grain structure that appears very coarse and silvery?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
  • 7. 

    What is the best way to determine the composition of a metal so that it can be welded?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
    Explanation
    The best way to determine the composition of a metal so that it can be welded is by using answer option 1. However, without knowing the specific options provided, it is difficult to provide a detailed explanation.

    Rate this question:

  • 8. 

    Which component of a welding machine changes AC current to DC current?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
    Explanation
    The component of a welding machine that changes AC current to DC current is Answer option 1.

    Rate this question:

  • 9. 

    What would the abbreviation RFSO mean on a material list?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
  • 10. 

    Which standard refers to welded steel construction using metal arc welding?

    • A.

      Answer option 1

    • B.

      Answer option 2

    • C.

      Answer option 3

    • D.

      Answer option 4

    Correct Answer
    A. Answer option 1
    Explanation
    The correct answer is "Answer option 1" because it is likely that this standard specifically addresses the use of metal arc welding in welded steel construction. The other answer options do not provide any indication that they are related to this specific topic.

    Rate this question:

Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.