2w051 CDC Set B
-
An electric saw’s blade must be operating at what speed before it contacts the material being cut?
-
Full
-
Slow.
-
Moderate.
-
Accelerated.
-
The 2W051 CDC Set B quiz assesses knowledge on using various maintenance tools such as drills and saws. It covers key operational standards like proper drill diameter, saw blade speeds, and air pressure requirements for pneumatic tools, essential for safe and efficient maintenance work.
Quiz Preview
- 2.
Which type of guidance system is also known as television guided
-
Electro-optical
-
Light energy.
-
Inertial.
-
Radar
Correct Answer
A. Electro-opticalExplanation
Electro-optical guidance system refers to the use of light energy and optical sensors to guide and track a target. It involves the transmission and reception of images and signals through the use of cameras and sensors. This type of guidance system is commonly known as television guided because it relies on visual information captured by cameras to guide the weapon or vehicle towards its target.Rate this question:
-
- 3.
When using a drill, the first thing you do is
-
Make sure the diameter of the hole to be drilled is within the capacity of the drill.
-
Connect the drill to the power source.
-
Put on your safety goggles.
-
Insert the chuck key.
Correct Answer
A. Make sure the diameter of the hole to be drilled is within the capacity of the drill.Explanation
Before using a drill, it is important to ensure that the diameter of the hole to be drilled is within the capacity of the drill. This is because drills have different capacities and trying to drill a hole larger than the drill can handle may damage the drill or cause it to malfunction. Therefore, it is necessary to check the drill's capacity and choose the appropriate drill bit size for the desired hole diameter.Rate this question:
-
- 4.
The MC–7 air compressor is designed for
-
Vehicle maintenance
-
General maintenance.
-
Aircraft servicing.
-
Paint sprayers.
Correct Answer
A. General maintenance.Explanation
The MC-7 air compressor is designed for general maintenance purposes. This means that it is suitable for a wide range of maintenance tasks, such as repairing machinery, fixing equipment, or performing regular upkeep on various items. It may not be specifically tailored for vehicle maintenance, aircraft servicing, or paint sprayers, but it can be used effectively for general maintenance needs.Rate this question:
-
- 5.
What provides an itemized list of all equipment authorized for use with nuclear weapons?
-
Master Nuclear Certification List
-
TO 00–35D–54.
-
TO 11A–1–10
-
TO 11A–1–63
Correct Answer
A. Master Nuclear Certification ListExplanation
The Master Nuclear Certification List provides an itemized list of all equipment authorized for use with nuclear weapons.Rate this question:
-
- 6.
What is the most common type of sling used in your everyday job?
-
Chain assembly
-
Web strapping.
-
Metal mesh.
-
Wire rope.
Correct Answer
A. Wire rope.Explanation
Wire rope is the most common type of sling used in everyday jobs because it is strong, durable, and versatile. It is made up of multiple strands of wire twisted together to form a strong and flexible rope. Wire rope slings are able to handle heavy loads and can be used in a variety of applications, such as lifting and rigging. They are also resistant to abrasion and can withstand harsh environments, making them suitable for everyday use in various industries.Rate this question:
-
- 7.
What is the largest caliber ammunition that we classify as “small arms”?
-
Caliber .38.
-
Caliber .50.
-
5.56 millimeter.
-
7.62
Correct Answer
A. Caliber .50.Explanation
The largest caliber ammunition that is classified as "small arms" is caliber .50. This means that any ammunition with a caliber larger than .50 would not be considered as small arms.Rate this question:
-
- 8.
When packing up the munitions assembly conveyor (MAC) why is it important to cap the ends of the air hoses?
-
To keep air from leaking out.
-
To keep the hose ends from being crushed.
-
To keep hydraulic fluid from leaking out
-
To keep foreign materials from damaging them
Correct Answer
A. To keep foreign materials from damaging themExplanation
When packing up the munitions assembly conveyor (MAC), it is important to cap the ends of the air hoses to keep foreign materials from damaging them. This is because if the ends of the hoses are left uncapped, dust, debris, or other foreign materials could enter the hoses and cause blockages or damage to the internal components. By capping the ends of the air hoses, the risk of damage from foreign materials is minimized, ensuring the proper functioning of the MAC system.Rate this question:
-
- 9.
What are the components of a typical small-arms cartridge
-
Cartridge case, primer, bullet, and propellant
-
Cartridge case, primer, bullet, and detonator
-
Cartridge case, shot pellets, and propellant.
-
Cartridge case, propellant, and tracer.
Correct Answer
A. Cartridge case, primer, bullet, and propellantExplanation
A typical small-arms cartridge consists of several components. The cartridge case holds all the other components together and provides structural support. The primer is located at the base of the cartridge case and contains a small amount of sensitive explosive material. When struck by the firing pin, the primer ignites and initiates the propellant. The propellant is a chemical compound that burns rapidly, generating a large volume of gas. This gas propels the bullet out of the cartridge case and down the barrel of the firearm. The bullet is the projectile that is fired from the firearm towards the target.Rate this question:
-
- 10.
What ensures the smooth transfer of HCU–6/E pallets from a rollerized trailer to an aircraft/K-loader?
-
A winch.
-
The use of J-bars.
-
An adjustable ramp.
-
The speed the pallet is moved
Correct Answer
A. An adjustable ramp.Explanation
An adjustable ramp ensures the smooth transfer of HCU-6/E pallets from a rollerized trailer to an aircraft/K-loader. This is because an adjustable ramp can be customized to match the height and angle of the aircraft's cargo door, allowing for a seamless transition of the pallets. The use of a winch, J-bars, or the speed of the pallet movement does not directly contribute to the smooth transfer process.Rate this question:
-
- 11.
What type of information is given in the general notes on the first card of each trailer and weapon-type section in TO 11–1–38 and is required to be reviewed
-
Illustrations for each trailer configuration
-
Equipment and quantity required for each trailer and weapon
-
WARNINGS, CAUTIONS, and NOTES pertaining to each trailer and weapon.
-
Equipment and quantity required for each trailer.
Correct Answer
A. WARNINGS, CAUTIONS, and NOTES pertaining to each trailer and weapon.Explanation
The general notes on the first card of each trailer and weapon-type section in TO 11-1-38 provide information about WARNINGS, CAUTIONS, and NOTES that are relevant to each trailer and weapon. These notes are important as they highlight any potential dangers, precautions, or additional information that the user needs to be aware of when using the trailer and weapon. Reviewing these warnings, cautions, and notes is necessary to ensure the safe and proper use of the equipment.Rate this question:
-
- 12.
The steering system on the MHU–141/M trailer has a turning radius of
-
100 inches
-
200 inches
-
400 inches
-
550 inches
Correct Answer
A. 200 inchesExplanation
The steering system on the MHU-141/M trailer has a turning radius of 200 inches. This means that the trailer can make a complete turn within a circle with a diameter of 400 inches. A smaller turning radius indicates that the trailer is more maneuverable and can navigate tighter turns.Rate this question:
-
- 13.
The parking brake on the MHU–110/M trailer affects how many wheels?
-
Four inboard rear wheels.
-
Two onboard rear wheels.
-
Rear two outboard rear wheels
-
Front two outboard rear wheels
Correct Answer
A. Four inboard rear wheels.Explanation
The parking brake on the MHU-110/M trailer affects all four inboard rear wheels. This means that when the parking brake is engaged, it will prevent all four of these wheels from moving, providing stability and preventing the trailer from rolling or moving unintentionally.Rate this question:
-
- 14.
What is a requirement for military explosives?
-
Raw materials must be cheap.
-
Raw materials must be nonhygroscopic.
-
Raw materials must be common to America
-
Raw materials must be vital to the war effort.
Correct Answer
A. Raw materials must be cheap.Explanation
Military explosives require raw materials that are cheap in order to be cost-effective and sustainable for the military. The cost of raw materials is an important factor in the production of explosives, as it directly impacts the overall cost of manufacturing and supplying them to the military. By using cheap raw materials, the military can ensure that they can produce a sufficient quantity of explosives within their budget. Additionally, using cheap raw materials allows for the allocation of funds to other essential military needs.Rate this question:
-
- 15.
Name two types of effects for signals.
-
Fire and flash.
-
Heat and flash.
-
Smoke and heat.
-
Light and smoke.
Correct Answer
A. Light and smoke.Explanation
The correct answer is "Light and smoke." This answer is correct because light and smoke are two types of effects that can be observed when signals are present. Light signals can be seen as a form of visual communication, such as traffic lights or emergency beacons. Smoke signals, on the other hand, are a type of visual signal created by burning materials, often used in emergency situations or for long-distance communication. Therefore, light and smoke are two distinct types of effects that can be associated with signals.Rate this question:
-
- 16.
How many pounds per square inch (psi) of clean, dry air are required at the tool end of the air hose to ensure safe and efficient operation of the tool?
-
70
-
90
-
110
-
130
Correct Answer
A. 90Explanation
To ensure safe and efficient operation of the tool, it is necessary to have 90 pounds per square inch (psi) of clean, dry air at the tool end of the air hose. This pressure is optimal for the tool to function effectively without causing any damage or inefficiency.Rate this question:
-
- 17.
The diesel model of the MC–7 air compressor is capable of operating up to how many hours at a time without refueling?
-
4
-
6
-
8
-
10
Correct Answer
A. 8Explanation
The diesel model of the MC-7 air compressor can operate for up to 8 hours without needing to be refueled.Rate this question:
-
- 18.
Movement to support on-base operations to or from the flight line is called
-
An operational movement.
-
An intrabase movement.
-
An on-base movement.
-
A logistical movement.
Correct Answer
A. An operational movement.Explanation
The correct answer is "an operational movement." This term refers to the movement of personnel or equipment to or from the flight line in order to support on-base operations. It is specifically related to activities that are necessary for the functioning of military operations and is different from other types of movements such as intrabase movements, on-base movements, and logistical movements.Rate this question:
-
- 19.
What shotgun round is the exception to the gauging principle?
-
10
-
12
-
28
-
410
Correct Answer
A. 410Explanation
The 410 shotgun round is the exception to the gauging principle because it is not measured in gauge like other shotgun rounds. Instead, it is measured in terms of its bore diameter, which is .410 inches. This means that the 410 shotgun round is smaller in diameter compared to other shotgun rounds, which are measured in gauge.Rate this question:
-
- 20.
Which component of the A/E32K–3 munitions assembly conveyor (MAC) can be used as a forklift adapter to raise the gantry to full height?
-
Gantry.
-
Rail conveyor.
-
Pneumatic hoist.
-
Interface control board (ICB).
Correct Answer
A. Interface control board (ICB).Explanation
The interface control board (ICB) can be used as a forklift adapter to raise the gantry to full height. This suggests that the ICB has the capability to connect with a forklift and assist in lifting the gantry to its maximum height.Rate this question:
-
- 21.
How are items identified as being nuclear certified
-
A certified item will be stamped “Nuclear certified.”
-
A certified item will be stenciled “Nuclear certified.”
-
Positive identification by a stamp, stencil, or etching.
-
Positive identification by a nameplate, label, appropriate markings, or by official documents.
Correct Answer
A. Positive identification by a nameplate, label, appropriate markings, or by official documents.Explanation
Certified items can be identified as being nuclear certified through positive identification by a nameplate, label, appropriate markings, or by official documents. This means that the item will have specific identifying features such as a nameplate or label indicating its certification, or it may have appropriate markings that indicate its nuclear certification status. Additionally, official documents can also be used to provide evidence of the item's nuclear certification.Rate this question:
-
- 22.
Which diameter (in inches) electric saw blade is the most common found in maintenance activities?
-
6
-
8
-
10
-
12
Correct Answer
A. 8Explanation
The most common diameter of an electric saw blade found in maintenance activities is 8 inches.Rate this question:
-
- 23.
Which pneumatic impact tool is designed for installing or removing nuts and bolts?
-
Hammer.
-
Wrench.
-
Socket.
-
Drill.
Correct Answer
A. Wrench.Explanation
A wrench is a pneumatic impact tool that is specifically designed for installing or removing nuts and bolts. It provides a strong grip and leverage to tighten or loosen fasteners with ease. A hammer is not designed for this purpose as it is used for striking or pounding objects. A socket is a type of attachment that is used with a wrench or a ratchet to provide a secure fit on nuts and bolts. A drill is a power tool that is used for drilling holes or driving screws, but it is not specifically designed for installing or removing nuts and bolts.Rate this question:
-
- 24.
The maximum towing speed of the bobtail while towing equipment is
-
10 mph
-
15 mph
-
20 mph
-
25 mph
Correct Answer
A. 15 mphExplanation
The correct answer is 15 mph. This means that the maximum speed at which the bobtail can tow equipment is 15 miles per hour. It is important to adhere to this speed limit to ensure safe towing and prevent any damage or accidents that may occur at higher speeds.Rate this question:
-
- 25.
What range should be selected in a tractor with an automatic transmission while going down grades?
-
Neutral
-
Low range.
-
High range.
-
Any range is acceptable.
Correct Answer
A. Low range.Explanation
When going down grades, it is recommended to select the low range in a tractor with an automatic transmission. This is because the low range provides higher torque and better engine braking, which helps in controlling the speed and preventing the vehicle from gaining excessive momentum while descending. By selecting the low range, the tractor can safely navigate downhill without putting excessive strain on the brakes or risking loss of control.Rate this question:
-
- 26.
The four factors that control the visibility of pyrotechnics are candlepower, color, weather, and
-
Light.
-
Altitude.
-
Humidity.
-
Chemical composition.
Correct Answer
A. Light.Explanation
The correct answer is light. Light is one of the factors that control the visibility of pyrotechnics. Pyrotechnics are fireworks or other types of explosive devices that produce light and color when ignited. The visibility of pyrotechnics is affected by the amount and intensity of light present in the environment. Factors such as candlepower, color, weather, altitude, humidity, and chemical composition may also have an impact, but the most significant factor in determining the visibility of pyrotechnics is light.Rate this question:
-
- 27.
Which 30 millimeter (mm) cannon is internally mounted in the A–10 aircraft?
-
M39.
-
M61.
-
GAU–8/A
-
GPU–5/A
Correct Answer
A. GAU–8/AExplanation
The correct answer is GAU-8/A. The GAU-8/A is a 30mm cannon that is internally mounted in the A-10 aircraft. It is a seven-barrel Gatling-type cannon that is known for its high rate of fire and its ability to effectively engage armored targets on the ground. The GAU-8/A is a key component of the A-10's close air support capabilities.Rate this question:
-
- 28.
The maximum load capacity of the MHU–141/M trailer is
-
1,500 pounds
-
3,000 pounds.
-
5,500 pounds
-
5,700 pounds.
Correct Answer
A. 5,500 poundsExplanation
The correct answer is 5,500 pounds. This means that the maximum load capacity of the MHU-141/M trailer is 5,500 pounds.Rate this question:
-
- 29.
The unique and handy feature of the bobtail truck’s center pintle hook is that it can be unpinned and
-
Removed for easier servicing of the truck.
-
Moved a maximum of 12 inches up or down.
-
Moved a maximum of 12 inches left or right of center.
-
Moved in, out, or sideways for ease of trailer hookup.
Correct Answer
A. Moved in, out, or sideways for ease of trailer hookup.Explanation
The bobtail truck's center pintle hook can be moved in, out, or sideways for ease of trailer hookup. This means that the hook can be adjusted to accommodate different trailer sizes and positions, making it easier to connect the truck and trailer together. This feature allows for more flexibility and convenience when attaching trailers to the truck.Rate this question:
-
- 30.
For what purpose do we use a shaped charge?
-
Bring down walls and collapse roofs.
-
No practical application in the munitions field.
-
Ignite rocket motors equipped with electric squibs
-
To produce an explosive penetration of a solid object.
Correct Answer
A. To produce an explosive penetration of a solid object.Explanation
A shaped charge is used to produce an explosive penetration of a solid object. This type of charge is designed in a way that focuses the energy of the explosion in a specific direction, allowing it to effectively penetrate and destroy solid objects such as walls or armored vehicles. It is commonly used in military applications, demolition, and other scenarios where controlled and targeted destruction is required.Rate this question:
-
- 31.
Which weapons replaceable assembly consists of the flex drive assembly?
-
Conveyor
-
Transfer unit.
-
Storage container.
-
Ammunition drum.
Correct Answer
A. ConveyorExplanation
The correct answer is Conveyor. The conveyor is the assembly that consists of the flex drive assembly. It is responsible for moving objects or materials from one place to another. In this case, it is specifically used for transporting weapons or ammunition.Rate this question:
-
- 32.
Which publication provides information on the correct positioning of munitions and tiedown procedures
-
TO 11–1–38
-
TO 11A–1–10.
-
TO 11A–1–63.
-
AFMAN 91–201
Correct Answer
A. TO 11–1–38Explanation
TO 11–1–38 is the correct answer because it is a publication that provides information on the correct positioning of munitions and tiedown procedures.Rate this question:
-
- 33.
In which type of guidance system does the weapon send out the tracking energy
-
Active.
-
Passive.
-
Semi-active.
-
Semi-passive.
Correct Answer
A. Active.Explanation
In an active guidance system, the weapon itself sends out tracking energy to locate and track the target. This tracking energy can be in the form of radar waves or other types of signals. Unlike passive guidance systems that rely on receiving signals from external sources or semi-active guidance systems that require the weapon to receive signals from another source, active guidance systems have their own energy source and actively emit signals to track the target.Rate this question:
-
- 34.
With electrical fuzes, what device is used in place of arming wire
-
Bungee cord.
-
Battery-firing device
-
Linear-shaped charge
Correct Answer
A. Battery-firing deviceExplanation
In electrical fuzes, a battery-firing device is used in place of an arming wire. This device is responsible for initiating the firing process by supplying the necessary electrical energy from a battery. Unlike an arming wire, which requires manual handling and connection, the battery-firing device provides a more efficient and automated method of arming the fuzes.Rate this question:
-
- 35.
Which lift truck has cantilever lift arms?
-
6,000-pound all-terrain forklift.
-
MHU–83-series bomb-lift truck
-
MJ–1-series aerial stores lift truck.
-
6,000-pound rough-terrain forklift.
Correct Answer
A. MJ–1-series aerial stores lift truck.Explanation
The correct answer is the MJ–1-series aerial stores lift truck. This type of lift truck is equipped with cantilever lift arms, which means that the arms are attached to a fixed point at one end and extend outward to support the load. Cantilever lift arms provide better stability and maneuverability when lifting and moving heavy loads, making them suitable for aerial stores lifting operations. The other options listed do not have cantilever lift arms.Rate this question:
-
- 36.
Volatility is the tendency of a substance to produce
-
Pressure
-
Energy
-
Vapors
-
Heat
Correct Answer
A. VaporsExplanation
Volatility refers to the tendency of a substance to evaporate or produce vapors. When a substance is volatile, it easily changes from a liquid or solid state to a gaseous state, releasing vapors. This is often influenced by factors such as temperature and pressure. Therefore, the correct answer in this case is "vapors".Rate this question:
-
- 37.
How many openings are on the deck of the MHU–226 trailer?
-
1
-
2
-
3
-
4
Correct Answer
A. 3Explanation
There are three openings on the deck of the MHU-226 trailer.Rate this question:
-
- 38.
Which lift truck has a manually extendible wheelbase?
-
6,000-pound all-terrain forklift.
-
MHU–83-series bomb-lift truck.
-
MJ–1-series aerial stores lift truck.
-
6,000-pound rough-terrain forklift.
Correct Answer
A. MHU–83-series bomb-lift truck.Explanation
The MHU-83-series bomb-lift truck has a manually extendible wheelbase.Rate this question:
-
- 39.
When releasing the accelerator pedal on a vehicle driven with a hydrostatic transmission, the
-
Lift truck stops immediately.
-
Unit rolls until its inertia is spent.
-
Unit coasts to a stop very quickly.
-
Transmission automatically drops to a lower gear, stopping forward motion.
Correct Answer
A. Unit coasts to a stop very quickly.Explanation
When releasing the accelerator pedal on a vehicle driven with a hydrostatic transmission, the unit coasts to a stop very quickly. This is because a hydrostatic transmission uses fluid to transmit power, and when the accelerator pedal is released, the fluid flow is cut off, causing the vehicle to quickly lose momentum and come to a stop. Unlike vehicles with traditional transmissions, there is no engine braking or automatic downshifting in a hydrostatic transmission, which is why the unit coasts to a stop rather than automatically dropping to a lower gear.Rate this question:
-
- 40.
What is the maximum tow capacity of the MB–4 aircraft towing tractor
-
120,000 pounds
-
130,000 pounds
-
140,000 pounds
-
150,000 pounds
Correct Answer
A. 140,000 poundsExplanation
The maximum tow capacity of the MB-4 aircraft towing tractor is 140,000 pounds.Rate this question:
-
- 41.
What is the inspection cycle for the universal ammunition loading system (UALS) replenisher?
-
Every 30 days when in use and annually when in storage
-
Every 45 days when in use and annually when in storage
-
Every 60 days when in use and annually when in storage
-
Every 90 days when in use and annually when in storage
Correct Answer
A. Every 30 days when in use and annually when in storageExplanation
The inspection cycle for the universal ammunition loading system (UALS) replenisher is every 30 days when in use and annually when in storage. This means that the UALS replenisher needs to be inspected every month when it is actively being used and once a year when it is not in use and in storage. Regular inspections ensure that the UALS replenisher is in proper working condition and ready for use when needed.Rate this question:
-
- 42.
At what variation in pounds of pressure, while using an impact wrench, can the excess pressure become serious?
-
20
-
15
-
10
-
5
Correct Answer
A. 5Explanation
When using an impact wrench, a variation of 5 pounds of pressure can cause the excess pressure to become serious. This means that if the pressure applied by the impact wrench exceeds the recommended or safe limit by 5 pounds, it can potentially lead to damage or injury. It is important to maintain proper control and ensure that the pressure is within the acceptable range to avoid any serious consequences.Rate this question:
-
- 43.
How many trolley and chock assemblies are supplied with the MHU–110/M?
-
10 trolleys and 20 chocks.
-
20 trolleys and 40 chocks.
-
20 trolleys and 10 chocks.
-
40 trolleys and 20 chocks.
Correct Answer
A. 20 trolleys and 40 chocks. -
- 44.
The moving of munitions and weapons from one base to another, depot to base, or base to depot is called
-
An off-base movement.
-
A logistical movement
-
An interbase movement.
-
An operational movement.
Correct Answer
A. A logistical movementExplanation
The correct answer is "a logistical movement". This term refers to the transportation and transfer of munitions and weapons between different military bases, depots, or other locations. It involves the coordination and management of resources, personnel, and equipment to ensure the safe and efficient movement of these assets. This term specifically highlights the logistical aspect of the movement, emphasizing the planning and execution involved in the process.Rate this question:
-
- 45.
The purpose of the BSU–84/B airfoil group (AFG) is to
-
Provide aerodynamic lift and stability during flight.
-
Create smooth and stable flight while in glide mode.
-
Provide steering commands for the control surfaces.
-
Steer the bomb and provides aerodynamic lift
Correct Answer
A. Provide aerodynamic lift and stability during flight.Explanation
The purpose of the BSU-84/B airfoil group (AFG) is to provide aerodynamic lift and stability during flight. This means that the AFG is responsible for generating the necessary lift force to keep the aircraft in the air and maintaining its stability while in flight. It does not have a role in creating smooth and stable flight in glide mode, providing steering commands for control surfaces, or steering the bomb.Rate this question:
-
- 46.
The common practice that applies to any meter is always
-
Set the meter lower than the estimated current
-
Verify that power is off when connecting the meter
-
Verify that power is on before connecting the meter
-
Set the meter scales to the lowest setting before turning on the meter.
Correct Answer
A. Verify that power is off when connecting the meterExplanation
When connecting a meter, it is important to verify that the power is off to ensure safety. This is because working on live circuits can be dangerous and can lead to electric shocks or other accidents. By confirming that the power is off before connecting the meter, one can prevent any potential harm and ensure a safe working environment.Rate this question:
-
- 47.
What is the maximum load capacity of the MHU–226 trailer?
-
6,000 pounds.
-
9,000 pounds.
-
12,000 pounds.
-
15,000 pounds.
Correct Answer
A. 12,000 pounds.Explanation
The maximum load capacity of the MHU-226 trailer is 12,000 pounds. This means that the trailer can carry a maximum weight of 12,000 pounds without exceeding its load capacity.Rate this question:
-
- 48.
What is the drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU–83 B/E?
-
Very labor intensive.
-
Difficult to make fine adjustment to the table
-
Extremely slow way to build hydraulic pressure.
-
Possible to damage hydraulic system due to overpressurization.
Correct Answer
A. Extremely slow way to build hydraulic pressure.Explanation
Using a hydraulic hand pump to build hydraulic pressure on the MHU-83 B/E is an extremely slow process. This means that it would take a significant amount of time and effort to reach the desired pressure level. This drawback can be inconvenient and inefficient, especially in situations where time is of the essence.Rate this question:
-
- 49.
Which type of forklift has a “dead-man” switch that can be operated from the driving position?
-
Gas
-
Diesel
-
Electric.
-
Propane
Correct Answer
A. Electric.Explanation
Electric forklifts have a "dead-man" switch that can be operated from the driving position. This switch is a safety feature that requires the operator to continuously press it in order for the forklift to move. If the operator releases the switch, the forklift will automatically stop, preventing any potential accidents or injuries. This feature ensures that the forklift is only in motion when there is an active operator present, enhancing safety in the workplace.Rate this question:
-
Quiz Review Timeline (Updated): Jan 20, 2025 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Jan 20, 2025Quiz Edited by
ProProfs Editorial Team -
Feb 03, 2013Quiz Created by
Rcargle
Back to top