2A553A Volume 1

1. What is used to submit recommendations for TO improvements?

TO appendix

AFTO Form 22

TO index

AF Form 1000

2. One way you can be relieved of property responsibility is to

Call the base equipment management office

Have the property declared unserviceable

Have the property declared surplus

Turn the property in to supply

3. The first five digits of a JCN indicate the

Year and Julian date

Last five digits of the equipment serial number

Month and year the maintenance discrepancy was discovered

First five digits of the equipment serial number

4. What is entered in block 15 of an AFTO Form 350 if an item is not reparable?

The signature of the performing work center supervisor

A brief description of the repair efforts

The letters NRTS and the not reparable this station code

A description of the malfunction

5. What factor gives Air Force wings, squadrons, and units the capability of fighting from main bases or bare bones forward operating locations at any level of combat?

Dispersed flying units

Strategic intelligence

Centralization

Decentralization

6. Who can give authorization for an aircraft to be flown while under a red X condition?

Wing commander

No one

Maintenance control supervisor

Base commander

7. What is not a function of the G081 Automated Maintenance Information System?

Missions scheduling

Personnel leave scheduling

Personnel training management

Maintenance scheduling

8. What type of property responsibility is applicable when a sergeant takes possession of a box that fell off an AF supply truck?

Supervisory

Custodial

Administrative

Comman

9. Where are the change pages inserted in existing TOs?

After the last page of the TO

Before the page of the same number

In place of the page of the same number

After the page of the same number

10. The data system used to assign and control computer program identification numbers is the

CAMS

ACPINS

ACMS

IMDS

11. The Air Force Instruction that governs the current wing organization and operation is

21-166

39-1

21-101

53-3

12. A work center that contributes labor towards a maintenance requirement is called the

Reporting work center

Nonreporting work center

Owning work center

Performing work center

13. When a person responsible for property is transferred, and the property remains with the organization, property responsibility

Is dropped

Stays in the organization

Is transferred to the supply squadron

Remains with the person

14. TO revisions

Include an appendix similar to change notices

Replace the original TO, including all changes and appendices

Are issued when 50 percent of the original TO is affected

Do not include a replacement for the title page

15. What flight in the MXS supports the field assistance support team for calibration?

Armament maintenance

Avionics

Accessory maintenance

TMDE

16. The MDC system data element used to tie together all maintenance actions on a specific job is the

Work center code

ID number

WUC

JCN

17. Who uses MDC system information for validating manpower requirements?

HQ USAF

HQ AMC

HQ ACC

HQ AETC

18. The IMDS is event oriented and user friendly, which means it

Accepts any input

Restricts unauthorized access

Checks keyboard entries for compatibility

Requires no password

19. Users of the G081 Automated Maintenance Information System know they are logged out when they see on the computer screen the word

BYE

MOBILITY

MAINTENANCE

END

20. In a basic TO, how are the pages of an appendix filed?

After the last page of the TO

In section number sequence throughout the TO

In front of the title page of the TO

In page number sequence throughout the TO

21. What does the -003 in S/S/SN 34-11-10-003 identify?

General procedure

LRU ID

Functional procedure

SRU ID

22. The ACPINS provides a standardized system that does not

Develop software

Identify software

Distribute software

Manage software

23. What is a responsibility of the maintenance operations center?

Ensure maintenance training is provided office, classroom, and hangar space

Review the guidance provided by the LG commander on cross functional areas

Ensure QA guidelines are being followed

Notify appropriate agencies of severe weather warnings.

24. The QAP is an assessment system used to

Monitor and report the status of electronic countermeasures and sensor pods

Maintain aircraft sortie rates

Determine aircraft and equipment condition, and personnel proficiency

Provide feedback to the OG commander

25. Where do you find the code to enter in the TYPE MAINT block of an AFTO Form 349?

In the maintenance TO

In the system WUC manual

On the manufacturer's data plate

On AF Form 2413

26. Which form provides an interface between on- and off-equipment maintenance documentation, and serves as an identification and status tag?

AF Form 2005

AFTO Form 350

AF Form 2413

AFTO Form 349

27. Of the four types of programs used in the G081 Automated Maintenance Information System, which is considered to be the "heart" of the system?

Data input

Data output

Batch

Variable information retrival

28. What MDC system data element is publised in manuals and REMIS tables for each weapon and support system?

Work center code

WUC

ID number

JCN

29. The number entered in the TAG NUMBER block of an AFTO Form 349 comes from

The AFTO Form 350

The manufacturer's data plate

The IPB

A WUC manual

30. The entry in the CAT LAB block on an AFTO Form 349 indicates the

Number of technicians performing the work

Type of equipment being repaired

Type of man-hour expenditure

Rank/rating of the technician

31. The primary purpose of the IMDS screen 380 is to

Provide an opportunity to modify entries found to be in error

Generate a new JCN and show time spent against this number

Maintain the present data and status of YR/EVENT IDs and work center events

Provide an up-to-date list of all open JCN

32. What supply printout provides the user a list of all parts ordered, but not received?

Daily document register

Due-out validation listing

Mission capability status report

Custodian authorization and custody receipt listing

33. Which statement best describes TOPS?

Unlike standard TO supplements, TOPS do not include a title page

TOPS can be issued only when procedural changes could cause personal injury

TOPS can be issued when the time factor prevents issuing a standard change

Like standard TO supplements, TOPS replace outdated TO pages

34. USAF customers must establish CPIN requirements through

Administrative contract officers

TO distribution offices

DOD contractors

Procuring contract officers

35. The MXG exists to

Manage on-equipment assets

Train and manage all personnel on base

Create and support the sortie-producing OG

Support the QA program

36. Who is accountable for equipment items?

Resources advisers and equipment custodian

Equipment manufacturers and supply personnel

Maintenance personnel and resources advisers

Supply personnel and equipment custodians

37. The fourth group of characters in Air Force TO number 1B-1B-2-6 identifies the

Section of sectionalized TO

Kind of TO

Equipment model or part number

Specific item of equipment

38. The JG in Air Force TO number 1C-141B-2-9JG-10 indicates the

Specific type of equipment

Specific model or series of TOs

Section of a sectionalized TO

Functional indicator of the TO

39. What type of Air Force TO do you use to locate all of the TOs pertaining to a certain type of equipment?

Alphabetical index

Cross-reference tables

List of applicable publications

Cross-utilization index

40. Section IV of the IPB provides information for cross-referencing

Figure, index number, and part number

TO page number, and cabinet, shelf, or drawer number of the reference designator

Figure, index number, and usable-on code

Vendors' code, figure, and IPB index number

41. What is not a responsibility of the CPIN system management office?

Foreign military sales case verification

Overall maintenance

Overall management

Foreign military sales development

42. In the CPIN identifier, the first field consists of

Subsystem and system codes

Computer software configuration item baseline code

Software-type code

Category and major function codes

43. What are AF policy directives?

Guidance documents consisting of procedures that usually contain examples for performing standard tasks.

Directives that prescribe the mission, area of responsibility, organization, responsibilities, and command relationships of AF units

Orders of the Secretary of the Air Force approved in the Secretariat or Air Staff and issued as departmental publications

44. What form is used for MDC when the IMDS is not available

AFTO Form 110

AF Form 2005

AFTO Form 349

AF FOrm 2413

45. In the Air Force, COTS technical manuals are normally identified by an

Assigned technical order number

Air Force stock number

Equipment part number

Equipment manufacturer ID number

46. Whose primary role is it to increase reliability and maintainability of aircraft and support equipment?

MXS commander

Wing operations center

QA

MXG commander

47. Supply discipline is best described as

Extra consideration to get the most from available resources

Command-directed supply procedures

Instructions given to protect AF resources

Protection given to AF resources

48. The originator sends a draft DR for screening to

The depot from which the item came

Base supply

The screening point

The squadron commander

49. The first group of characters in Air Force TO number 33D7-10-1 identifies the

Specific item of equipment

Section of a sectionalized TO

Kind of TO

Equipment's major system

50. What types of TCTO can be identified by a red X or circled red X, respectively, alternately spaced around the border?

Immediate and urgent

Routine and emergency

Emergency and immediate

Routine and urgent

51. In the OMMS job guide, what type of procedure is component adjustment/alignment?

Functional fault isolation

Functional maintenance

General maintenance

General fault isolation

52. What type of number identifies a preliminary TO?

Change number

Sequential copy number

Odd number

Supplement number

53. When the fifth element of a S/S/SN is -3, the type of component procedure indicated is

Inspection

Repair

Adjustment

Installation

54. In fault code 32-41-19-001-2, the -001 identifies a faulty

SRU

LRU

Subsystem

Sub-subsystem

55. Which type of MDC system data is not used at base level?

Configuration status accounting

Production credit information

Determination of the cost of military work hours

Analysis of NRTS actions

56. What AFTO Form is used as an accountability document for items managed under the DIFM program?

781

350

349

244

57. Correcting erroneous data in the IMDS is a function of

Data reporting

Database management

The error detection subsystem

Information retrieval

58. The on-hand quantity of bench stock items does not normally exceed

90 days

120 days

60 days

30 days

59. What type of DR requires submission by message within three workdays after the discovery of the deficiency?

Category II

Materiel

Category I

Software

60. The IMDS is a

Command-level computer system used for maintenance management

Base-level computer system used for maintenance management

Command-level computer system used for supply management

Base-level computer system used for supply management

61. Material deficiency reporting procedures are found in Air Force TO

00-25D-54

00-35D-35

00-25D-55

00-35D-54

62. The authorized types of TO supplements are

Interim, safety, and operational

Routine, safety, and formal

Safety, operational, and interim

Routine, safety, and operational

63. An X placed in the SCH CODE block of an AFTO Form 349 indicates

An unscheduled maintenance action has been performed

The computer must calculate the next calibration or maintenance due date

Additional maintenance must be scheduled

The maintenance action has been rescheduled

64. What IMDS screen displays a maintenance snapshot inquiry?

380

142

122

054

65. What Air Force technical order is not a type of TCTO?

Record

Interim

Emergency action

Urgent action

66. What does the alpha code in reference designator 3231FC01 identify?

Sub-subsystem

Component type

LRU ID

Diagram reference

67. Informational publications that include procedures for implementing AF policies are called

Supplements

Directories

Indexes

Pamphlets

68. What column of section II of the IPB contains the letters NAS?

Usable on code

Source, maintenance, and recoverability code

Part number

Federal Supply Code for Manufacturers

69. What documents consist of procedures that usually contain examples for performing standard tasks?

AF policy directives

AF manuals

Mission directives

AF instructions

70. Air Force technical manuals that contain data for the operation and servicing of aircraft equipment are called

Commercial manuals

Job guides

Aircraft TOs

Other equipment TOs

71. What type of TCTO is used to correct conditions that could result in fatal or serious injury?

Routine

Immediate

Emergency

Urgent

72. Promoting unit self-sufficiency through the effective use of maintenance resources is the responsibility of the

Maintenance group commander

Maintenance operations center

Wing commander

Maintenance operations officer

73. What type of property responsibility requires that directives and instructions be issued?

Supervisory

Command

Administrative

Custodial

74. An OMMS general system manual proves

Fault descriptions and fault isolation procedures

Detailed schematics of systems wiring

Detailed procedures for on-aircraft maintenance

A general overview of the aircraft

75. Which ACPINS major function is used to deny unauthorized requests?

Management products

Data entry and database maintenance

Distribution

Requirements

76. Monitoring and supporting the flight line maintenance effort is the responsibility of the

Maintenance group commander

Maintenance operations officer

Maintenance operations center

Wing operations center

77. Statements of the Office of the Secretary of the Air Force and HQ USAF used to initiate, govern, or regulate actions are called

AF manuals

Mission directives

AF policy directives

AF instructions

78. The symbol you enter on inspection forms when an urgent-action TCTO is received is a

Red X

Circle red X

Red diagonal

Red dash

79. The Air Force TO numbering system is explained in detail in TO

0-1-01

00-5-18

00-5-1

0-4-2

80. An OMMS job guide manual includes

Functional maintenance procedures

Output conditions pages

A means of identifying and reporting faults

General systems theory

81. There are how many general types of ACPINS compendiums?

Five

Four

Six

Three

82. What is the primary sources of information for equipment configuration status at base, command, and depot levels?

Advanced configuration management system

MDC system

Maintenance cost system

IMDS

83. Dates entered on an AFTO Form 350 that pertain to repair cycle times are used

To identify time-change requirements

As an aid in determining spares requirements

For determining manpower manpower requirements

For establishing equipment need dates

84. The introduction to section I of the IPB provides the user the capability of cross-referencing

Reference designators and figure numbers

Reference designators and index numbers

Part numbers and reference designators

Part numbers and figures

85. In the Air Force TO system, what TO list all TO indexes?

0-1-CD-01

0-1-CD-1-2

0-1-CD-1

0-1-CD-1-1

86. An OMMS fault reporting manual provides

A means of conveying fault information

Detailed schematics of system wiring

Fault descriptions and fault isolation procedures

The identity of fault codes at pre-flight briefings

87. A CPIN is composed of how many identifier fields?

Four

Six

Five

Three

88. An ACPINS cross-reference compendium contains

A list of currently published ACPINS compendiums

Computer software configuration items assigned to major equipment

Quick references for research aids

Command-managed computer program identification numbers

89. Unit nonexpendable equipment authorizations are based on

Funding and number of personnel authorized

Requirements and funding

Unit mission and number of personnel authorized

Unit mission and readily available equipment

90. Publications that contain instructions for use of equipment, in addition to data contained in other manuals, are identified as

COTS manuals

Supplemental manuals

Replacements

Other equipment technical orders

91. How many separate components may a CPIN have?

One

Two

Four

Three

92. In the Air Force TO system, what index TO contains a cross-reference listing of data code numbers assigned to active TCTOs?

0-4-2

00-5-1

00-5-2

0-4-1

93. The types of TO improvement reports are

Emergency, immediate, and routine

Immediate and urgent

Emergency, urgent, and routine

Emergency and urgent

94. Section I of the IPB provides information on use of codes and designations fount in the TO and

Cross-reference information on related supply publications

A table of contents for the IPB

A list of related TOs

A list of part numbers cross-references to stock numbers

95. The TO that list all Air Force MPTO is TO

0-1-1

00-1-02

00-1-20

0-1-02

96. The REMIS is designed to provide information to support AF

Data for the DDN

Data for the IMDS

Document production data for the MDC system

Equipment maintenance program

97. What is entered in column C of an AFTO Form 349 to document a TCTO?

The WUC

The first five characters of the TCTO data code or command-assigned data

The first five characters of the national item identification number

The TCTO support general code

98. The Air Force TO that gives detailed instructions for preparing and submitting an AFTO Form 22 is

00-5-2

00-20 series

00-5-1

00-5-15

99. What publication contains broad, enduring guidance for preparing and employing AF resources?

AF manuals

AF policy directives

AF doctrine documents

Mission directives

100. Informational publications that are compilations of systematically arranged information are called

Indexes

Directories

Pamphlets

Supplements

2a553a Volume 1