2A051N Vol. 4

1. For safe operation the V-508 dolly truck handles are attached using

Straps

Latches

Adhesive

Locking pins

2. Which C9492 button initiates an interruptive centrally integrated test system (CITS) when interfaced with an AN/ALQ-131 pod?

RESET

DIM

ALT

BIT

3. Which C9492 control switch function item controls the brightness of the eight push buttons and the back panel lighting?

BIT

ALT

DIM

SPL

4. What interface/control (IC) subsystem is the functional heart of the AN/ALQ-131 pod?

IC

Millicomputer

Waveform generator

Radar warning receiver interface

5. Which of these pieces of equipment is used in developing simulated radar threats?

Oscilloscope

Spectrum Analyzer

Digital Multimeter

Pulse/function generator

6. A common condition that will cause a blower failure on the AN/ALM-233 power control monitor unit (PCMU) is

Properly operating fans

An open cabinet door

Cables on the floor

A clogged air filter

7. What is the correct turn-on and turn-off sequence of the AN/ALQ-131 pod IC module's +5 and +15 voltages?

+5V on first and off first, +15V on last and off last

+5V on last and off first, +15V on first and off last

+5V on first and off last, +15V on last and off first

+5V on last and off last, +15V on first and off first

8. What happens if an amplifier gains too much amplitude while cycling through a regenerative feedback loop?

The amplifier shuts off

The amplifier saturates

An exponential rate of decay

The extra gain will spill over

9. Which factor involving automatic gain optimization (AGO) can be planned for?

Regenerative feedback

Load configuration

Weapons stores

Aircraft

10. How is mid/high band automatic gain optimization (AGO) calculated in the AN/ALQ-184 pod?

On a subband basis

Identical to low band

On a beam-by-beam basis

Identical to the AN/ALQ-131 pod

11. What AN/ALQ-131 canister item contains a fill-and-bleed port for refrigerent, a level indicator, and a pressure relief diaphram?

Plug

Condenser

Evaporator

Manifold Block

12. For shop cooling, water can be circulated through the AN/ALQ-131 pod

Forward to aft

Aft to forward

From top to bottom

Either forward to aft or aft to forward

13. Which C9492 push button light associated with the AN/ALQ-131 indicates an active button and that the pod is responding to that button?

"A"

"F"

"S"

"T"

14. The RF interface assembly's (RFIA) RF output switch routes the selected source instrument's inputs to

J1 (SWEEP) and j2 (PULSE)

J8 (RF OUT) and j11(RF REF)

J2 (PULSE) and j5 (PULSE TEE)

J17 (PULSE GEN IN) and j19 (FCTN GEN IN)

15. What AN/ALQ-131 pod module has a reference designator of "9"?

Aft transition antenna module

Transition module

Receiver/Processor

Interface/control

16. What test console panel contains the digital functions required to interconnect the intermediate level support equipment (ILSE) control console to the ALQ-131 pod's digibus aerospace ground equipment (AGE) connector?

Power distribution panel

Power console panel

Pod interface panel

Pod control panel

17. Which canister module is located at the front of the AN/ALQ-184 pod?

A1

A2

A3

A4

18. Which AN/ALQ-184 pod module contains the pod system processor?

A1

A2

A3

A4

19. What mode is the AN/ALQ-184 pod in when the C9492 is in transmit 2 (XMIT2) with no buttons pushed?

Mode 3 special

Mode 4 standby

Mode 6 special

Mode 7 standby

20. AN/ALQ-131 pod relay 8k3 creates what signal once all three phases of power close it through its sensor windings?

XEN

VSEN

AC SEL

OVFDET

21. Which "unwanted R" is common with antennas and dummy loads where a component feeds back into itself?

Ripple

Roll off

Ringing

Voltage standing wave ratio (VSWR)

22. Which intermediate level support equipment (ILSE) console contains the RF interface assembly (RFIA)?

Test Console

Control Console

Instrument console 1

Instrument console 2

23. On the AN/ALQ-131 pod the inerruptive centrally integrated test system (ICITS) can split into

High power and low power

High level and low level

Abbreviated and normal

Long and short

24. Along with tracking and blanking information, the types of information that are passed over the AN/ALQ-131 pod's time critical are bus band status,

Test setups, and frequencies

Self test faults, and video signals

Software updates, and seft test status

Module faults, and control commands

25. Which situation is not suitable for noise generation in the AN/ALQ-131 pod?

Loading software

Tecnique generation

Shop centrally integrated test system (CITS)

Compensated automatic gain optimization (AGO) routine

26. AN/ALQ-184 pod system calibration tests are performed every

90 days

120 days

180 days

360 days

27. Which intermediate level support equipment (ILSE) console contains a flat screen monitor that is used to present technicians with options for running tests and alignments?

Test console

Control Console

Instrument console 1

Instrument Console 2

28. Which chapter in each of the AN/ALQ-131 band TO's give transmit control assembly individual circuit card information?

1

3

6

7

29. Which ALQ-131 pod interface panel circuit board has the capability to test external C9492 units?

Controller board

Bus tie unit board

Digibus driver board

Pulse position data board

30. What AN/ALQ-131 techniques are internally genrated by using a voltage controlled oscillator?

Noise

Repeater

Transponder

All of these

31. The AN/ALQ-131 pod's three basic jammer responses for processing RF threats are noise,

Repeater, and deception

Reception, and deception

Repeater, and transponder

Receiver, and transponder

32. What AN/ALM-233 SCU CCA checks DC voltage and processor operation?

Look-through blanking CCA

RF switching control CCA

Built-in-test CCA

Pulse CCA

33. The Low Voltage Power Supply Load Box Assembly can test which of the following module low voltage power supplies?

Band 4, receiver/processor (RP) module, and interface/control (IC) module

Band 3, band 4, RP module, and IC module

Band 3, band 4, and RP module

Band 3, band 5, and IC module

34. The intermediate level support equipment (ILSE) board substitution group contains how many boards?

12

15

16

25

35. Which voltage remains uninhibited during the AN/ALQ-131 pod's band turn-on sequence?

+5V

+12V

+15V

+30V

36. How many unique CITS histories can the AN/ALQ-131 pod store at a time?

4

6

8

12

37. Which term is not part of the Hypot test group used with the AN/ALQ-131 pod?

Spark gap test set

Hypot adapter box

High Voltage leads and adapters

High voltage power supply test set

38. What is considered a full load for a low voltage power supply using the low voltage power supply load box with the AN/ALQ-184?

75 %

85 %

90 %

100 %

39. When used with the AN/ALQ-184 pod, what does the dot located on the lower right quadrant of switch S5 of the C9492 indicate?

Pod fault

An unused lamp

RUN SILENT mode

Combat tapes are loaded

40. What AN/ALQ-131 centrally integrated test system (CITS) status signal communicates the presence or absense of high-level voltage output from the output power supply used to drive the traveling wave tube (TWT) in the RF output stage?

CWF

CHV

CXTD

CMSTBY

41. When using the C9492 with the AN/ALQ-131, when the selector switch is OFF where is power still applied to the pod?

8K2 and 8K3

8K1 and 8K2

10K1 and 8K1

8K1, 8K2, and 8K3

42. What mode does the control console computer use to direct the necessary commands through the IEE-488 data interface bus to the RF interface assembly (RFIA)?

Front

Local

Remote

Manual

43. AN/ALQ-131 software is loaded into the millicomputer in what format?

Serial

Binary

Parallel

Alphanumeric

44. Which best describes the tests used to ensure replacement shop replacable units (SRUs) correct pod faults, that no new faults have been introduced, and any necessary calibration adjustments are performed?

Program verification

System calibration

Harmonization

Alignments

45. What AN/ALQ-131 pod module has a reference designator of "8"?

Aft transmit antenna module

Transition module

Receiver/Processor

Interface/control

46. In the AN/ALQ-131 preset mode, which push-buttons are used to select different software preset technique combinations?

1 through 8

1 through 5

5 through 8

None

47. When using the AN/ALM-187 High Voltage Power Supply test Set, what procedure permits stress testing and calibrating an output power supply prior to traveling wave tube (TWT) operation?

Hypot

Load

In-line

Burn-in

48. What two detection units in the AN/ALM-233 signal conditioner unit (SCU) are used for RF-to-video conversion during internal operation?

Zener diode and crystal rectifier

Crystal detector and crystal rectifier

Zener diode and crystal video receiver

Crystal detector and crystal video receiver

49. What AN/ALQ-131 pod relay can be bypassed using the ram air turbine generator setup?

10k1

8k1

8k2

8k3

50. The AN/ALQ-184 low band palette can hold up to how many technique commands?

24

36

48

64

51. For dash operations the AN/ALQ-131 pod's water-cooled condenser regulator maintains pressue of at least 9 psia in order to maintain the minimum boiling temperature of the water at

190 Deg F

206 Deg F

212 Deg F

235 Deg F

52. Which "unwanted R" causes the scalar network analyzer SNA screen to look compressed along the horizontal frequency axis?

Ripple

Ringing

Roll off

Voltage standing wave ratio (VSWR)

53. How many high power RF couplers are in the aft transmit antenna module of the AN/ALQ-131 pod?

1

2

3

4

54. How many resistors on each AN/ALQ-131 pod antenna board are used for adjusting threshold voltages for output power monitoring?

1

3

5

7

55. Which RF interface assembly (RFIA) board provides remote status indications for the front panel switches of the RFIA?

IEEE-488 interface board

Input/output (I/O) board

Controller board

Processor board

56. How often are operational statuses of the AN/ALQ-131 on-board modules reported by sensing selected system parameters?

10 milliseconds

20 milliseconds

50 milliseconds

Every second

57. Since the AN/ALQ-184 low-band does not have dedicated automatic gain optimization (AGO) attenuators, linear attenuators are needed, and technicians use the ASE to develop a table that is calibrated in what increments?

1dB

2dB

3dB

10dB

58. The AN/ALM-233 pod's coldplate liquid cooler is capable of delivering coolant to the coldplate assemblies at a rate of

1.5 +/- 0.2 gallons per minute

2.6 +/- 0.4 gpm

2.8 +/- 0.2 gpm

3.2 +/- 0.3 gpm

59. One advantage of the C6631 alternate control box is that when used with the AN/ALQ-131 pod it bypasses which standby relay?

10k1

10k2

8k1

8k2

60. How many CITS sensors are dedicated to each band of the AN/ALQ-131 pod?

2

3

4

6

61. What type of communication link is the AN/ALQ-131 pod's digibus?

8-bit serial

16- bit serial

8-bit parallel

16-bit parallel

62. Where is the first place that attenuation is applied to stop ringing during the AN/ALQ-131 pod's AGO process?

MIN control manual adjustable attenuator (MAA)

Bulk voltage variable attenuator (VVA)

Channel VVA

Aft VVA

63. How many separate pod support rings comprise the AN/ALM-233 pod maintenance fixtures?

2

3

4

6

64. What component was added to the AN/ALQ-184 pod auxiliary receiver to prevent normal thermal noise from the amplifier accidently activating the crystal video receivers (CVR)?

Field effect transistor (FET) amplifier

Crystal detector

Limiter switch

Attenuator

65. The RP A15 circuit board belongs to what section of the AN/ALQ-131 pod's RP module?

Video processor

Computer

Receiver

Tracker

66. Which bus does AN/ALQ-131 pod connector 14A1J3 interface with?

RS-423

RS-232

IEEE-488

MIL-STD-1553

67. Which RF interface assembly (RFIA) board inputs commands from the control console to the RFIA?

IEEE-488 interface board

Input/Output board

Controller board

Processor board

68. What is the reference designator of the IC core memory?

10A6

10A9

10A16

10A19

69. What AN/ALQ-184 techiniques generator CCA measures error between YTHG picket and selected VCO during set-on?

Non-standard interface multiplexor

Channel noise control

Noise controller

Set-on control

70. In the ALQ-188 pod, what modulation technique does the radio transmitter modulator use?

Mixing

Separating

Serrodyning

Heterodyning

71. The AN/ALM-233 amplifier/filter is located between the

PCMU and SCU

SCU and receiver shield

Receiver shield and pod

Pod and transmit shield

72. What AN/ALQ-184 pod section receives compressed video signals from the linear RF modules to help identify the subband a threat was received in before sending data to the pod system processor (PSP)?

Aux receiver

Subband processor

Technique generator

Logarithmic RF modules

73. What AN/ALQ-184 PSP CCA determine AGO, repeater, and CW transmit modes?

High-Voltage power supply (HVPS) Data Aquisition CCA

Program controller CCA

Receiver status CCA

Mode control CCA

74. Activating which AN/ALQ-131 pod relay begins the millicomputer start-up routine?

10k1

8k1

8k2

8k3

75. What are the three major types of data contained in the AN/ALQ-131 pod's arithmetic unit?

Control data, circuit status data, and register stack data

Control data, circuit status data, and computer program data

Control data, computer program data, and register stack data

Circuit status data, computer program data, and register stack data

76. Which AN/ALQ-131 pod self tests must be run when the pod is loaded with an operational flight program?

Interruptive centrally integrated test system (ICITS), continuous centrally integrated tet system (CCITS), and shop centrally integrated test system (SCITS)

ICITS and SCITS

CCITS and ICITS

CCITS and SCITS

77. The ALQ-188 pod is capable of generating how many different jamming modes?

15

20

25

30

78. What AN/ALM-233 DICMU CCA receive 9 digital and 3 narrow band analog signals from the test point multiplexor (TP MUX) CCA and routes the selected analog and/or digital signals to the signal conditioner CCA?

Central processig unit CCA

Test point router CCA

Bus termination CCA

BIT CCA

79. What AN/ALQ-184 pod mid/high band receiver is dedicated for continous wave (CW) signals?

Angle of Arrival (AOA) receiver

Superheterodyne processor

Auxiliary receiver

Subband receiver

80. Which AN/ALQ-184 pod traveling wave tubes (TWTs) can be tested using the high voltage test unit?

Mid and high band

Low band only

Mid band only

All of these

81. How many individual VCOs are included in the AN/ALQ-184 techniques generator's VCO subsystem?

6

9

10

12

82. In what AN/AQ-131 pod power source condition do all DC low voltages first become available to the interface/control IC and receiver/processor RP modules?

Pod off

Pod standby

Module standby

High voltage ready

83. What AN/ALQ-131 pod IC circuit board is dedicated for radar-warning reciever (RWR) interface?

A1

A2

A3

A4

84. For proper operation of the AN/ALM-233 the relative humidity should be between

0 to 60 %

40 to 60 %

20 to 90 %

10 to 95 %

85. How many microprocessors are located in the AN/ALQ-184 pod?

12

15

16

24

86. Which switches on the C9492 for the AN/ALQ-184 pod have ID lights on them?

S1 through s4

S1 through s6

S1 through s7

S1 through s8

87. What IC circuit board is used to help control antenna tilt and monitor RF power at the AN/ALQ-131 pod's transmit antenna?

A1

A2

A3

A4

88. in which AN/ALQ-131 pod power sounrce conditions are all eight band low voltages available for use?

Pod Standby, module standby, high voltage ready, and high voltage on

Module standby, high voltage ready, and high voltage on

Pod standby and module ready

All 5 pod power source conditions

89. What AN/ALQ-131 centrally integrated test system (CITS) status signal communicates the completion of the time delay required before applying high voltage to the module?

CWF

CHV

CXTD

CMSTBY

90. What AN/ALM-233 SCU circuit card assembly (CCA) provides independent control of the switches in the angle of arrival (AOA) and angle of transmission (AOT) test sets?

Look-through blanking CCA

RF switch control CCA

Built-in-test CCA

Pulse CCA

91. What AN/ALM-233 SCU CCA provides independent control of the switches in the AOA and AOT test sets?

Look-through blanking CCA

RF switch control CCA

Built-in-test CCA

Pulse CCA

92. What AN/ALQ-184 PSP CCA translate latched address lines from the CPU into register enable strobes for all registers in the PSP and latch correlators in the subband processor?

Pulse descriptive word (PDW) timing CCA

Auxiliary receiver detect CCA

External address decoder

Program controller

93. The AN/ALM-233 amplifier/filter assembly provides selection for how many separate frequency paths?

2

3

4

6

94. What provides the means by which the ASE can monitor all test points of the AN/ALQ-184 low band module?

Test point multiplexer CCAs

Test point adapter assembly

RF termination unit

Amplifier/filter

95. What does the AN/ALQ-184 pulse descriptive word processor resolve so that only one subband processes signals in the frequency crossover region?

Subband crossover ambiguities

Multithreat processing

Beamport selection

Beamport priority

96. What AN/ALM-233 digital interface/control monitor unit (DI/CMU) CCA monitors the +5VDC, +15 VDC, and -15 VDC power supplies, and generates interrupts when an under-voltage or over-voltage condition occurs?

Built-in test CCA

Test point router CCA

Central processing unit CCA

Test point multiplexer control CCA

97. A three-band AN/ALQ-131 pod contains how many total circuit breakers?

1

2

3

4

98. How many receivers are located in the AN/ALQ-131's receiver/processor (RP) module?

1

2

3

4

99. The AN/ALQ-184 pod's serial I/O CCA perform conversioin from parallel to serial and back for MLV/ASE communication, RWR interface, techniques generator, VCO assembly, and what other communication bus?

Auxiliary receiver communications

Complex waveform generator

Low band communications

Digibus

100. How long does the AN/ALQ-184 system controller count pulses detected in each subband to determine if a programmed hit-count has been exceeded?

10 microseconds

10 milliseconds

100 microseconds

100 milliseconds

2A051N Vol. 4

1. For safe operation the V-508 dolly truck handles are attached using

2.

What first name or nickname would you like us to use?

2. Which C9492 button initiates an interruptive centrally integrated test system (CITS) when interfaced with an AN/ALQ-131 pod?

3. Which C9492 control switch function item controls the brightness of the eight push buttons and the back panel lighting?

4. What interface/control (IC) subsystem is the functional heart of the AN/ALQ-131 pod?

5. Which of these pieces of equipment is used in developing simulated radar threats?

6. A common condition that will cause a blower failure on the AN/ALM-233 power control monitor unit (PCMU) is

7. What is the correct turn-on and turn-off sequence of the AN/ALQ-131 pod IC module's +5 and +15 voltages?

8. What happens if an amplifier gains too much amplitude while cycling through a regenerative feedback loop?

9. Which factor involving automatic gain optimization (AGO) can be planned for?

10. How is mid/high band automatic gain optimization (AGO) calculated in the AN/ALQ-184 pod?

11. What AN/ALQ-131 canister item contains a fill-and-bleed port for refrigerent, a level indicator, and a pressure relief diaphram?

12. For shop cooling, water can be circulated through the AN/ALQ-131 pod

13. Which C9492 push button light associated with the AN/ALQ-131 indicates an active button and that the pod is responding to that button?

14. The RF interface assembly's (RFIA) RF output switch routes the selected source instrument's inputs to

15. What AN/ALQ-131 pod module has a reference designator of "9"?

16. What test console panel contains the digital functions required to interconnect the intermediate level support equipment (ILSE) control console to the ALQ-131 pod's digibus aerospace ground equipment (AGE) connector?

17. Which canister module is located at the front of the AN/ALQ-184 pod?

18. Which AN/ALQ-184 pod module contains the pod system processor?

19. What mode is the AN/ALQ-184 pod in when the C9492 is in transmit 2 (XMIT2) with no buttons pushed?

20. AN/ALQ-131 pod relay 8k3 creates what signal once all three phases of power close it through its sensor windings?

21. Which "unwanted R" is common with antennas and dummy loads where a component feeds back into itself?

22. Which intermediate level support equipment (ILSE) console contains the RF interface assembly (RFIA)?

23. On the AN/ALQ-131 pod the inerruptive centrally integrated test system (ICITS) can split into

24. Along with tracking and blanking information, the types of information that are passed over the AN/ALQ-131 pod's time critical are bus band status,

25. Which situation is not suitable for noise generation in the AN/ALQ-131 pod?

26. AN/ALQ-184 pod system calibration tests are performed every

27. Which intermediate level support equipment (ILSE) console contains a flat screen monitor that is used to present technicians with options for running tests and alignments?

28. Which chapter in each of the AN/ALQ-131 band TO's give transmit control assembly individual circuit card information?

29. Which ALQ-131 pod interface panel circuit board has the capability to test external C9492 units?

30. What AN/ALQ-131 techniques are internally genrated by using a voltage controlled oscillator?

31. The AN/ALQ-131 pod's three basic jammer responses for processing RF threats are noise,

32. What AN/ALM-233 SCU CCA checks DC voltage and processor operation?

33. The Low Voltage Power Supply Load Box Assembly can test which of the following module low voltage power supplies?

34. The intermediate level support equipment (ILSE) board substitution group contains how many boards?

35. Which voltage remains uninhibited during the AN/ALQ-131 pod's band turn-on sequence?

36. How many unique CITS histories can the AN/ALQ-131 pod store at a time?

37. Which term is not part of the Hypot test group used with the AN/ALQ-131 pod?

38. What is considered a full load for a low voltage power supply using the low voltage power supply load box with the AN/ALQ-184?

39. When used with the AN/ALQ-184 pod, what does the dot located on the lower right quadrant of switch S5 of the C9492 indicate?

40. What AN/ALQ-131 centrally integrated test system (CITS) status signal communicates the presence or absense of high-level voltage output from the output power supply used to drive the traveling wave tube (TWT) in the RF output stage?

41. When using the C9492 with the AN/ALQ-131, when the selector switch is OFF where is power still applied to the pod?

42. What mode does the control console computer use to direct the necessary commands through the IEE-488 data interface bus to the RF interface assembly (RFIA)?

43. AN/ALQ-131 software is loaded into the millicomputer in what format?

44. Which best describes the tests used to ensure replacement shop replacable units (SRUs) correct pod faults, that no new faults have been introduced, and any necessary calibration adjustments are performed?

45. What AN/ALQ-131 pod module has a reference designator of "8"?

46. In the AN/ALQ-131 preset mode, which push-buttons are used to select different software preset technique combinations?

47. When using the AN/ALM-187 High Voltage Power Supply test Set, what procedure permits stress testing and calibrating an output power supply prior to traveling wave tube (TWT) operation?

48. What two detection units in the AN/ALM-233 signal conditioner unit (SCU) are used for RF-to-video conversion during internal operation?

49. What AN/ALQ-131 pod relay can be bypassed using the ram air turbine generator setup?

50. The AN/ALQ-184 low band palette can hold up to how many technique commands?

51. For dash operations the AN/ALQ-131 pod's water-cooled condenser regulator maintains pressue of at least 9 psia in order to maintain the minimum boiling temperature of the water at

52. Which "unwanted R" causes the scalar network analyzer SNA screen to look compressed along the horizontal frequency axis?

53. How many high power RF couplers are in the aft transmit antenna module of the AN/ALQ-131 pod?

54. How many resistors on each AN/ALQ-131 pod antenna board are used for adjusting threshold voltages for output power monitoring?

55. Which RF interface assembly (RFIA) board provides remote status indications for the front panel switches of the RFIA?

56. How often are operational statuses of the AN/ALQ-131 on-board modules reported by sensing selected system parameters?

57. Since the AN/ALQ-184 low-band does not have dedicated automatic gain optimization (AGO) attenuators, linear attenuators are needed, and technicians use the ASE to develop a table that is calibrated in what increments?

58. The AN/ALM-233 pod's coldplate liquid cooler is capable of delivering coolant to the coldplate assemblies at a rate of

59. One advantage of the C6631 alternate control box is that when used with the AN/ALQ-131 pod it bypasses which standby relay?

60. How many CITS sensors are dedicated to each band of the AN/ALQ-131 pod?

61. What type of communication link is the AN/ALQ-131 pod's digibus?

62. Where is the first place that attenuation is applied to stop ringing during the AN/ALQ-131 pod's AGO process?

63. How many separate pod support rings comprise the AN/ALM-233 pod maintenance fixtures?

64. What component was added to the AN/ALQ-184 pod auxiliary receiver to prevent normal thermal noise from the amplifier accidently activating the crystal video receivers (CVR)?

65. The RP A15 circuit board belongs to what section of the AN/ALQ-131 pod's RP module?

66. Which bus does AN/ALQ-131 pod connector 14A1J3 interface with?

67. Which RF interface assembly (RFIA) board inputs commands from the control console to the RFIA?

68. What is the reference designator of the IC core memory?

69. What AN/ALQ-184 techiniques generator CCA measures error between YTHG picket and selected VCO during set-on?

70. In the ALQ-188 pod, what modulation technique does the radio transmitter modulator use?

71. The AN/ALM-233 amplifier/filter is located between the

72. What AN/ALQ-184 pod section receives compressed video signals from the linear RF modules to help identify the subband a threat was received in before sending data to the pod system processor (PSP)?

73. What AN/ALQ-184 PSP CCA determine AGO, repeater, and CW transmit modes?

74. Activating which AN/ALQ-131 pod relay begins the millicomputer start-up routine?

75. What are the three major types of data contained in the AN/ALQ-131 pod's arithmetic unit?

76. Which AN/ALQ-131 pod self tests must be run when the pod is loaded with an operational flight program?

77. The ALQ-188 pod is capable of generating how many different jamming modes?