Tesla CAD Modelling Prelims
-
In Autocad, what is the command that is used to rotate the grid at 45 degress?
Rules and Regulations: Totally 15 questions will be there , 2 questions will be fill in the blanks and remaining will be multiple choice question. Total time limit is 10 minutes. Participant must attend all the question. After finishing test, result will be displayed on the screen. Selected candidates are intimated through Mobile. So, Please keep your phone number active. BEST See moreOF LUCK. . . . TAKE THE QUIZ!. . . . . . .
(25).webp "Tesla CAD Modelling Prelims - Quiz")
Quiz Preview
- 2.
When creating your own blocks it is important to avoid drawing any portion of the block in the ________ layer.
-
0
-
Center line
-
Hatch
-
Hidden line
Correct Answer
A. 0Explanation
When creating your own blocks, it is important to avoid drawing any portion of the block in the 0 layer.Rate this question:
-
- 3.
In order to set drawing limits for a "C" size architectural drawing the drafter should set the limits to ________.
-
0,0 and 2,9
-
0,0 and 17,11
-
0,0 and 18,24
-
0,0 and 34,24
Correct Answer
A. 0,0 and 18,24Explanation
The correct answer is 0,0 and 18,24. This is because "C" size architectural drawings typically have dimensions of 18 inches by 24 inches. By setting the drawing limits to 0,0 and 18,24, the drafter ensures that the entire drawing will fit within these dimensions.Rate this question:
-
- 4.
When setting up a mechanical drawing in AutoCAD the drafter should set the units to ________.
-
Fractional
-
Decimal
-
Architectural
-
Metric
Correct Answer
A. DecimalExplanation
When setting up a mechanical drawing in AutoCAD, it is recommended to set the units to decimal. This is because decimal units are commonly used in mechanical engineering and provide a more precise and accurate representation of measurements. Decimal units allow for easier calculations and conversions between different units of measurement, making it the preferred choice for mechanical drawings in AutoCAD.Rate this question:
-
- 5.
When drawing a line using the relative coordinate system a line is created from ________.
-
0,0
-
The ending point of the last line
-
The beginning point of the last line
-
None of the above
Correct Answer
A. The ending point of the last lineExplanation
When drawing a line using the relative coordinate system, the line is created starting from the ending point of the last line. This means that the coordinates of the new line are calculated relative to the ending point of the previous line. By using the relative coordinate system, the position of each line is determined based on the previous line's ending point, allowing for the creation of a continuous path.Rate this question:
-
- 6.
A line with a tapering width can be easily created by using the ________ tool.
-
Circle
-
eclipse
-
Line
-
Polyline
Correct Answer
A. PolylineExplanation
A polyline is a tool that allows for the creation of lines with varying widths. By manipulating the control points of the polyline, the width can be adjusted to create a line with a tapering effect. This makes the polyline tool the ideal choice for creating a line with a tapering width. The other options, such as circle, ellipse, and line, do not have the capability to create a tapering width.Rate this question:
-
- 7.
One of the below options is wrong about type of Autocad drawing units. Which one is it?
-
Architectural
-
Engineering
-
Millimeter
-
Decimal
Correct Answer
A. MillimeterExplanation
The incorrect option about the type of AutoCAD drawing units is "Millimeter". AutoCAD does support millimeters as a unit of measurement for drawings. The other options, Architectural, Engineering, and Decimal, are all valid unit types in AutoCAD.Rate this question:
-
- 8.
PTC Abbreviation ________ .
Correct Answer
Parametric Technology Corporation
parametric technology corporationExplanation
The correct answer is "Parametric Technology Corporation" or "parametric technology corporation" because PTC is an abbreviation for this company.Rate this question:
- 9.
The View toolbar will position the view of the 3-D solid toward the ________.
-
Front
-
Left side
-
SE isometric
-
All of the above
Correct Answer
A. All of the aboveExplanation
The View toolbar in a 3-D solid modeling software allows users to manipulate the viewpoint of the solid. "Front" refers to the front view of the solid, "left side" refers to the left side view, and "SE isometric" refers to the southeast isometric view. Therefore, selecting "all of the above" means that the View toolbar can position the view of the 3-D solid towards any of these directions.Rate this question:
-
- 10.
The curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam is
-
Displacement diagram
-
Follower
-
Cam cycle
-
Reciprocation chart
Correct Answer
A. Displacement diagramExplanation
The correct answer is "Displacement diagram." A displacement diagram is a curve that represents the displacement of the follower as ordinates on a base line that represents one revolution of the cam. It shows the movement of the follower in relation to the rotation of the cam, allowing for analysis and understanding of the cam mechanism's behavior.Rate this question:
-
- 11.
The typical parts list should include the ________.
-
Part number
-
Manufacturing material
-
Number of parts needed
-
All of the above
Correct Answer
A. All of the aboveExplanation
The typical parts list should include all of the above. A parts list typically includes the part number, which helps in identifying and ordering the correct part. It also includes the manufacturing material, which is important for understanding the characteristics and properties of the part. Additionally, the number of parts needed is mentioned in the list to ensure that the correct quantity is procured. Therefore, all these elements are essential and should be included in a typical parts list.Rate this question:
-
- 12.
This is an angled surface used on cylinders to make them easier to handle:
-
Fillet
-
Taper
-
Chamfer
-
Lug
Correct Answer
A. ChamferExplanation
A chamfer is an angled surface that is used on cylinders to make them easier to handle. It is typically created by cutting or grinding away the sharp edge or corner of the cylinder, resulting in a beveled or sloping surface. This chamfered surface helps to prevent any sharp edges or corners from causing injury or damage, and also makes it easier to grip and handle the cylinder.Rate this question:
-
- 13.
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
-
O Snaps
-
Ortho
-
Grid
-
Dynamic input
Correct Answer
A. O SnapsExplanation
To ensure precise placement when inserting blocks into a drawing file, the drafter should make sure that "O Snaps" is turned on. O Snaps, or object snaps, allow the drafter to snap the cursor to specific points or objects in the drawing, such as endpoints, midpoints, intersections, etc. This feature helps in accurately aligning and positioning the blocks within the drawing.Rate this question:
-
- 14.
Which Key do you press to cycle through the available snap points?
-
Ctrl
-
Shift
-
Tab
-
Alt
Correct Answer
A. TabExplanation
To cycle through the available snap points, you press the Tab key. The Tab key is commonly used to move the focus between different elements or sections within a program or interface. In this context, pressing Tab allows the user to navigate and select different snap points, which are predetermined positions or alignments that objects can snap to for precise placement or alignment purposes.Rate this question:
-
- 15.
Pro/ENGINEER has been rebranded, indicating that it’s a first step on the path to Creo – what’s the new name?
-
Creo Elements/Direct
-
Creo Elements/Pro
-
Creo Elements/View
Correct Answer
A. Creo Elements/ProExplanation
Pro/ENGINEER has been rebranded as Creo Elements/Pro, indicating that it is the first step towards the new software called Creo.Rate this question:
-
Quiz Review Timeline (Updated): May 19, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
May 19, 2023Quiz Edited by
ProProfs Editorial Team -
Sep 14, 2015Quiz Created by
Tesla15
Back to top