Z2f051 Volume 1 Unit Review Exercises

1. (001) To find a chapter or section heading in a specific publication, you would first look in the

Chapter index.

Table of contents.

Publication index.

Alphabetical index.

2. (002) Who do you contact to gain access to the Enhanced Technical Information Management System (ETIMS)?

Squadron Records Monitor.

Flight Publications Monitor.

Flight Technical Order Distribution Office Representative.

Squadron Technical Order Distribution Office Representative.

3. (001) Which improvement recommendation should be submitted for a technical order (TO) deficiency that could result in a fatal or serious injury, or damaged equipment?

Urgent.

Routine

Emergency.

Time compliance.

4. (001) Within how many hours is the responsible technical content manager required to take action on a technical order (TO) emergency improvement recommendation report?

6.

12.

24.

48.

5. (001) Which technical order (TO) improvement recommendation suggests improvements involving a potentially hazardous condition?

Urgent.

Routine.

Emergency.

Critical hazard.

6. (001) Which technical order (TO) improvement recommendation requires a reply within 45 days?

Urgent.

Routine.

Emergency.

Critical hazard.

7. (001) These are considered specialized publications.

Journals.

Staff digests.

Technical orders.

Narrative summaries.

8. (001) Which type of AF publication includes instructions and manuals?

Standard.

Technical.

Recurring.

Specialized.

9. (001) An example of a directive standard publication is a

Bulletin.

Pamphlet.

Staff digest.

Supplement.

10. (002) When using the Enhanced Technical Information Management System (ETIMS), you locate a technical order (TO) when only the TO series is known by typing the

Series in the “TO Date” block.

Title in the “Stock Number” block.

Series number in the “TO number” block.

Title in the “Word Search on Title” block.

11. (001) Publications that set up management standards and control the official business of the Air Force are called

Manuals.

Pamphlets.

Instructions.

Operating instructions

12. (001) Which type of standard publication contains step-by-step directives telling how to accomplish specific tasks or operations?

Manuals.

Pamphlets.

Instructions.

Technical orders.

13. (002) Which block would you enter the form or publication title in when searching by title for an electronic standard publication on the Air Force e-Publishing website?

Find it.

Search Products.

Advance Search.

Electronic Publications.

14. (003) What characteristic refers to how easy a liquid changes into a vapor state?

Volatility.

Viscosity.

Boiling point.

Vapor pressure.

15. 1. (001) A technical order (TO) that lists all of the TOs applicable to a specific military system is called a

Technical order index.

Technical order catalog.

C. list of applicable publications (LOAP).

D. numerical index and requirements tables (NI&RT).

a. technical order index. b. technical order catalog. c. list of applicable publications (LOAP). d. numerical index and requirements tables (NI&RT).

Explanation

a. technical order index. b. technical order catalog. c. list of applicable publications (LOAP). d. numerical index and requirements tables (NI&RT).

16. (001) Publications that announce policies and prescribe procedures within a single manager's area of authority are called

Bulletins.

Supplements.

Branch notices.

Operating instructions.

17. (001) The technical order (TO) that explains the procedures for reporting improvements in TOs is

TO 00–5–1, AF Technical Order System.

TO 00–5–15, AF Time Compliance Technical Order Process

TO 00–5–18. Methods and Procedures AF Technical Order Numbering System

TO 00–5–3, Methods and Procedures AF Technical Order Life cycle Management.

a. TO 00–5–1, AF Technical Order System. b. TO 00–5–15, AF Time Compliance Technical Order Process. c. TO 00–5–18. Methods and Procedures AF Technical Order Numbering System. d. TO 00–5–3, Methods and Procedures AF Technical Order Life cycle Management.

Explanation

a. TO 00–5–1, AF Technical Order System. b. TO 00–5–15, AF Time Compliance Technical Order Process. c. TO 00–5–18. Methods and Procedures AF Technical Order Numbering System. d. TO 00–5–3, Methods and Procedures AF Technical Order Life cycle Management.

18. (003) This term is used to describe the temperature at which a liquid actively starts to vaporize.

Volatility.

Fire point.

Flash point.

Boiling point.

19. (001) Which form would you most likely use to report technical order (TO) deficiencies?

AF Form 457, USAF Hazard Report.

AFTO Form 422, Differential Pressure Log.

AF Form 847, Recommendation for Change of Publication.

AFTO Form 22, Technical Manual (TM) Change Recommendation and Reply.

20. (001) Which technical order is issued to correct unsafe conditions that could cause a severe or fatal injury?

Safety.

Abbreviated.

Time compliance.

Methods and procedures.

21. (005) Operating aircraft can produce noise levels in these decibel ranges.

40 to 90

80 to 100

90 to 110

110 to 130

22. (004) Which is not a hazard of liquid nitrogen?

Reduces the concentration of oxygen.

Freezes or badly damages human tissue upon contact.

Burns or explodes upon contact with oil, grease, and jet fuel.

Builds up to tremendous pressure if it evaporates in a confined area.

23. (005) Which vehicles do not have to yield the right of way to moving aircraft?

“Follow Me” trucks.

Refueling units.

Fire trucks.

Tugs.

24. (006) Who drafts and reviews the spill prevention and response (SPR) plan at each installation?

Spill response team.

Environmental coordinator.

Bioenvironmental engineer.

Environmental Safety and Occupational Health Council.

25. (005) For safety measures, all Air Force electrical equipment must have

Grounded plugs.

Single insulation.

Double insulation.

Explosion-proof plugs.

26. (005) What minimum safe distance (feet) should be maintained from the front and sides of jet intakes?

10

15

25

50

27. (006) To detect pollutant releases, monitor underground storage tanks every

15 Days

30 Days

45 Days

60 Days

28. (005) How many minutes must pass after filling a tank before inserting any object, such as a tape and bob to determine the level of the fuel?

15

20

30

35

29. (005) At a minimum, how many feet behind an aircraft's operating jet is considered safe?

50

100

150

200

30. (006) To observe environmental pollution precautions, check dikes for deterioration

Daily

Weekly

Monthly

Semiannually

31. (005) In instances where security fences are not provided around fuel storage areas, how many feet will signs be posted from diked areas, tank vents, low point drains, and lateral control pits?

50

75

100

200

32. (006) As a pollution control precaution, dike drain valves

Must be locked open to drain the dikes constantly.

Should not be connected to the base industrial water system.

Are not required for dikes around aboveground tanks over 2,000 gallons.

Must be locked in the closed position when the dikes are not being drained.

33. (007) Within what time frame of an incident occurring should the fuels management team (FMT) send an initial mishap notification to HQ USAF/A4LE, The Directorate of Logistics Materiel Support Division, Fuels?

Within 24 hours of the mishap.

Within 48 hours of the mishap.

By the end of the first duty day after the mishap.

By the end of the third duty day after the mishap.

34. (005) What is the maximum allowable speed when driving a special-purpose vehicle on the flight line?

5

10

15

20

35. (005) When color-coding piping systems, what color is used as a primary warning for all flammable gases and liquids?

Red

Black

Green

Yellow

36. (003) Combustible liquids have a flash point higher than

100 degrees (°) Fahrenheit (F).

120° F.

140° F.

150° F.

37. (007) Which of the following base agencies should the fuels management team (FMT) coordinate with to obtain equipment needed for entering toxic environments?

Wing safety.

Spill response team.

Base civil engineering.

Environmental protection committee.

38. (005) What directive requires that an effective safety program be established within the fuels flight?

AFMAN 48–153, Health Risk Assessment.

AFI 91–202, The US Air Force Mishap Prevention Program.

AFMAN 48–155, Occupational and Environmental Health Exposure Controls.

AFI 91–302, Air Force Occupational and Environmental Safety, Fire Protection, and Health Standards.

39. (005) How often should fill stand emergency shutdown switches be tested for proper operation while the system is operating?

Daily

Weekly

Monthly

Yellow

40. (007) Which outside agency acts as the Air Force's Service Control Point (SCP)?

Defense Logistics Agency Energy (DLA-Energy).

Headquarters United States Air Force (HQ USAF).

Air Force Petroleum Agency (AFPA).

Major command (MAJCOM).

41. (005) Emergency shutdown switches should be located no closer than this many feet from fill stands.

25

50

75

100

42. (005) Fire reporting telephone stations must be located within how many feet of all fixed fueling points?

150

250

300

500

43. (007) To which outside agency should the fuels management team (FMT) forward their mishap reports?

Major command (MAJCOM).

Defense Logistics Agency Energy (DLA-Energy).

Air Force Petroleum Agency Office (AFPA).

Headquarters United States Air Force (HQ USAF).

44. (008) How often should the Vehicle Maintenance Flight Material Control section conduct a written inventory on composite tool kits?

Monthly.

Quarterly.

Annually.

Semiannually.

45. (005) What does a flashing red and green light signal from the control tower mean to a moving vehicle on the flight line?

General warning, use extreme caution.

Return to starting point.

Safe to cross.

Stop.

46. (005) When driving a fuel servicing vehicle while approaching a taxiing aircraft at night, move out of the taxi path,

Slow down, and turn off the headlight.

Stop the vehicle, and leave the headlights on.

Slow down, and leave the headlights on.

Stop the vehicle, and turn the headlights off.

47. (005) What is the minimum capacity for aboveground storage tanks that would require a dike area?

561 gallons

661 gallons

561 Barrels

661 Barrels

48. (005) When positioning a refueling vehicle for servicing, you should under no circumstances position it any closer than this minimum distance (feet) from any portion of an aircraft.

5

10

25

50

49. (005) Prior to performing off-loading operations in an unsecure area, danger signs should be placed how many feet in the front and to the rear of tank trucks?

25

50

75

100

50. (005) Fuel servicing operations should not be conducted within this many feet of operating aircraft radar.

100

150

200

300

51. (005) All of the following operations may continue when electrical storms are within 5 nautical miles of the servicing area except

Transfer operations.

Fill stand operations.

Base service station issues.

Commercial pipeline receipts.

52. (005) This condition can exist and you do not have to stop cryogenic production.

When electrical storms are within 1 nautical mile.

When electric storms are within 3 nautical miles.

When electrical storms are within 5 nautical miles.

When electrical storms are within 7 nautical miles.

53. (005) Which base agency determines hearing protection requirements for cryogenic operations?

Civil engineering.

Fuels management flight.

Environmental Protection Agency.

Bioenvironmental engineering services.

54. (005) What is the minimum fire rating for all interior walls separating the laboratory from other portions of the building?

15 Minutes

30 Minutes

45 Minutes

1 Hour

55. (005) A fuel spill less than 2 feet in any direction is classified in this spill category.

Class I.

Class II

Class III

Class IV

56. (005) What is the minimum number of minutes that must pass to eliminate static charges before disassembling an in-line sampler?

4

3

2

1

57. (005) Which fuel spill classification involves an area not more than 10 feet in any direction?

Class I

Class II

Class III

Class IV

58. (005) What is the maximum amount (gallons) of test fuel permitted in a fuel laboratory?

5

10

20

25

59. Mark A. for this question

Correct answer

Wrong

60. (008) Joint inventories on individual tool kits are conducted by the technician and the Vehicle Maintenance Flight Materiel Control section

Daily.

Annually.

Monthly.

Semiannually.

61. (005) Which source of accidents is the principle cause of disabling injuries to office workers?

Falling.

Using hand tools.

Handling heavy equipment.

Striking against material or equipment.

62. (005) What should you do first when fighting an electrical fire?

Aim the fire extinguisher at the base of the fire.

Contact the base interior electric shop.

Locate a water-type fire extinguisher.

Disable the circuit.

63. (005) Much time and expense are involved in investigating and

Solving accidents.

Reporting accidents.

Validating accidents.

Discovering accidents.

64. (003) What is the minimum flash point of JP–5 jet fuel?

–20 degrees (°) Fahrenheit (F).

–40° F.

100° F.

140° F.

65. (005) Water pressure fire extinguishers are effective on this class of fire.

A

B

C

D

66. (003) What is the freeze point for JP–8 jet fuel?

–51 degrees (°) Celsius (C).

–58° C.

–51° Fahrenheit (F).

–58° F.

67. (005) Which class of fuel spill should be declared as a ground accident?

Class I

Class II

Class III

Class IV

68. (005) What is the proper treatment for someone who has been splashed with cryogenic liquid?

Rewarm the body part as soon as possible.

Wrap the exposed area in a cotton blanket.

Watch closely and treat for shock.

Give the victim plenty of liquids.

Z2f051 Volume 1 Unit Review Exercises

1. (001) To find a chapter or section heading in a specific publication, you would first look in the

2.

What first name or nickname would you like us to use?

2. (002) Who do you contact to gain access to the Enhanced Technical Information Management System (ETIMS)?

3. (001) Which improvement recommendation should be submitted for a technical order (TO) deficiency that could result in a fatal or serious injury, or damaged equipment?

4. (001) Within how many hours is the responsible technical content manager required to take action on a technical order (TO) emergency improvement recommendation report?

5. (001) Which technical order (TO) improvement recommendation suggests improvements involving a potentially hazardous condition?

6. (001) Which technical order (TO) improvement recommendation requires a reply within 45 days?

7. (001) These are considered specialized publications.

8. (001) Which type of AF publication includes instructions and manuals?

9. (001) An example of a directive standard publication is a

10. (002) When using the Enhanced Technical Information Management System (ETIMS), you locate a technical order (TO) when only the TO series is known by typing the

11. (001) Publications that set up management standards and control the official business of the Air Force are called

12. (001) Which type of standard publication contains step-by-step directives telling how to accomplish specific tasks or operations?

13. (002) Which block would you enter the form or publication title in when searching by title for an electronic standard publication on the Air Force e-Publishing website?

14. (003) What characteristic refers to how easy a liquid changes into a vapor state?

15. 1. (001) A technical order (TO) that lists all of the TOs applicable to a specific military system is called a

16. (001) Publications that announce policies and prescribe procedures within a single manager's area of authority are called

17. (001) The technical order (TO) that explains the procedures for reporting improvements in TOs is

18. (003) This term is used to describe the temperature at which a liquid actively starts to vaporize.

19. (001) Which form would you most likely use to report technical order (TO) deficiencies?

20. (001) Which technical order is issued to correct unsafe conditions that could cause a severe or fatal injury?

21. (005) Operating aircraft can produce noise levels in these decibel ranges.

22. (004) Which is not a hazard of liquid nitrogen?

23. (005) Which vehicles do not have to yield the right of way to moving aircraft?

24. (006) Who drafts and reviews the spill prevention and response (SPR) plan at each installation?

25. (005) For safety measures, all Air Force electrical equipment must have

26. (005) What minimum safe distance (feet) should be maintained from the front and sides of jet intakes?

27. (006) To detect pollutant releases, monitor underground storage tanks every

28. (005) How many minutes must pass after filling a tank before inserting any object, such as a tape and bob to determine the level of the fuel?

29. (005) At a minimum, how many feet behind an aircraft's operating jet is considered safe?

30. (006) To observe environmental pollution precautions, check dikes for deterioration

31. (005) In instances where security fences are not provided around fuel storage areas, how many feet will signs be posted from diked areas, tank vents, low point drains, and lateral control pits?

32. (006) As a pollution control precaution, dike drain valves

33. (007) Within what time frame of an incident occurring should the fuels management team (FMT) send an initial mishap notification to HQ USAF/A4LE, The Directorate of Logistics Materiel Support Division, Fuels?

34. (005) What is the maximum allowable speed when driving a special-purpose vehicle on the flight line?

35. (005) When color-coding piping systems, what color is used as a primary warning for all flammable gases and liquids?

36. (003) Combustible liquids have a flash point higher than

37. (007) Which of the following base agencies should the fuels management team (FMT) coordinate with to obtain equipment needed for entering toxic environments?

38. (005) What directive requires that an effective safety program be established within the fuels flight?

39. (005) How often should fill stand emergency shutdown switches be tested for proper operation while the system is operating?

40. (007) Which outside agency acts as the Air Force's Service Control Point (SCP)?

41. (005) Emergency shutdown switches should be located no closer than this many feet from fill stands.

42. (005) Fire reporting telephone stations must be located within how many feet of all fixed fueling points?

43. (007) To which outside agency should the fuels management team (FMT) forward their mishap reports?

44. (008) How often should the Vehicle Maintenance Flight Material Control section conduct a written inventory on composite tool kits?

45. (005) What does a flashing red and green light signal from the control tower mean to a moving vehicle on the flight line?

46. (005) When driving a fuel servicing vehicle while approaching a taxiing aircraft at night, move out of the taxi path,

47. (005) What is the minimum capacity for aboveground storage tanks that would require a dike area?

48. (005) When positioning a refueling vehicle for servicing, you should under no circumstances position it any closer than this minimum distance (feet) from any portion of an aircraft.

49. (005) Prior to performing off-loading operations in an unsecure area, danger signs should be placed how many feet in the front and to the rear of tank trucks?

50. (005) Fuel servicing operations should not be conducted within this many feet of operating aircraft radar.

51. (005) All of the following operations may continue when electrical storms are within 5 nautical miles of the servicing area except

52. (005) This condition can exist and you do not have to stop cryogenic production.

53. (005) Which base agency determines hearing protection requirements for cryogenic operations?

54. (005) What is the minimum fire rating for all interior walls separating the laboratory from other portions of the building?

55. (005) A fuel spill less than 2 feet in any direction is classified in this spill category.

56. (005) What is the minimum number of minutes that must pass to eliminate static charges before disassembling an in-line sampler?

57. (005) Which fuel spill classification involves an area not more than 10 feet in any direction?

58. (005) What is the maximum amount (gallons) of test fuel permitted in a fuel laboratory?

59. Mark A. for this question

60. (008) Joint inventories on individual tool kits are conducted by the technician and the Vehicle Maintenance Flight Materiel Control section

61. (005) Which source of accidents is the principle cause of disabling injuries to office workers?

62. (005) What should you do first when fighting an electrical fire?

63. (005) Much time and expense are involved in investigating and

64. (003) What is the minimum flash point of JP–5 jet fuel?

65. (005) Water pressure fire extinguishers are effective on this class of fire.

66. (003) What is the freeze point for JP–8 jet fuel?

67. (005) Which class of fuel spill should be declared as a ground accident?

68. (005) What is the proper treatment for someone who has been splashed with cryogenic liquid?