BP 220 Batas Pambansa 220

1. A building designed or used as residence for one or more families.

Dwelling

Facilities

Parks

A dwelling refers to a building that is specifically designed or used as a residence for one or more families. It is a place where people live and call their home. This term encompasses various types of housing structures, such as houses, apartments, condominiums, or townhouses. The word "dwelling" emphasizes the purpose of the building, which is to provide a living space for individuals or families.

Explanation

A dwelling refers to a building that is specifically designed or used as a residence for one or more families. It is a place where people live and call their home. This term encompasses various types of housing structures, such as houses, apartments, condominiums, or townhouses. The word "dwelling" emphasizes the purpose of the building, which is to provide a living space for individuals or families.

2. How much in percentage of parks and playgrounds must be allocated for 201 - 225 dwelling units?

6%

5%

3.5%

7%

The correct answer is 7%. This means that 7% of the total area for parks and playgrounds should be allocated for 201 - 225 dwelling units. This suggests that a larger proportion of the area should be dedicated to parks and playgrounds in order to accommodate the higher number of dwelling units.

Explanation

The correct answer is 7%. This means that 7% of the total area for parks and playgrounds should be allocated for 201 - 225 dwelling units. This suggests that a larger proportion of the area should be dedicated to parks and playgrounds in order to accommodate the higher number of dwelling units.

3. HOW MANY PERCENT OF COMMUNITY FACILITIES WILL BE PROVIDE IF THE PROJECT HOUSING WILL BE 225 AND ABOVE DWELLING UNITS

1

1.5

2

The correct answer is 2. If the project housing consists of 225 or more dwelling units, then 2 percent of community facilities will be provided.

Explanation

The correct answer is 2. If the project housing consists of 225 or more dwelling units, then 2 percent of community facilities will be provided.

4. The minimum door widths for toilet and baths

0.90

0.50

0.60

The correct answer is 0.60. This is the minimum door width requirement for toilets and baths. It is important to have a door width of at least 0.60 meters to ensure accessibility and ease of use for individuals using the facilities. Doors with a width less than 0.60 meters may not provide enough space for people to comfortably enter and exit the toilet or bath area.

Explanation

The correct answer is 0.60. This is the minimum door width requirement for toilets and baths. It is important to have a door width of at least 0.60 meters to ensure accessibility and ease of use for individuals using the facilities. Doors with a width less than 0.60 meters may not provide enough space for people to comfortably enter and exit the toilet or bath area.

5. A dwelling for one family which is completely surrounded by permanent open spaces, with independent access, services, and use of land.

Single-family detached

Single family attached

Rowhouses

A single-family detached dwelling refers to a house that is not connected to any other houses and is surrounded by permanent open spaces. It has independent access, services, and use of land. This means that the house is not part of a larger building or complex and provides privacy and exclusivity for the family living in it.

Explanation

A single-family detached dwelling refers to a house that is not connected to any other houses and is surrounded by permanent open spaces. It has independent access, services, and use of land. This means that the house is not part of a larger building or complex and provides privacy and exclusivity for the family living in it.

6. How much in percentage of parks and playgrounds must be allocated for 161-175 dwelling units?

3.5%

5%

6%

7%

The correct answer is 5% because it is the percentage that must be allocated for parks and playgrounds for 161-175 dwelling units. This means that out of the total area or space available for development, 5% should be dedicated to parks and playgrounds.

Explanation

The correct answer is 5% because it is the percentage that must be allocated for parks and playgrounds for 161-175 dwelling units. This means that out of the total area or space available for development, 5% should be dedicated to parks and playgrounds.

7. 1 COMMUNITY FACILITIES WILL BE PROVIDED FOR HOUSING PROJECTS AND WILL BE MANDATORY FOR HOW MUCH IN HECTARE

1 AND ABOVE

2 AND ABAVE

3 AND ABOVE

4 AND ABOVE

Community facilities will be provided for housing projects that are 1 hectare or larger. This means that any housing project that is 1 hectare or more will be required to have community facilities.

Explanation

Community facilities will be provided for housing projects that are 1 hectare or larger. This means that any housing project that is 1 hectare or more will be required to have community facilities.

8. A parcel of land bounded on the sides by streets or alleys or pathways or other natural or manmade features, and occupied by or intended for buildings.

Block

Plot

Parcel

A block refers to a parcel of land that is surrounded by streets, alleys, pathways, or other natural or manmade features, and is intended for buildings. It is a defined area that can be developed or occupied by structures.

Explanation

A block refers to a parcel of land that is surrounded by streets, alleys, pathways, or other natural or manmade features, and is intended for buildings. It is a defined area that can be developed or occupied by structures.

9. How much in percentage of parks and playgrounds must be allocated for 226 dwelling units?

7%

4%

9%

5%

The correct answer is 9%. This means that 9% of the total area must be allocated for parks and playgrounds in order to accommodate the 226 dwelling units.

Explanation

The correct answer is 9%. This means that 9% of the total area must be allocated for parks and playgrounds in order to accommodate the 226 dwelling units.

10. HOW MANY PERCENT OF COMMUNITY FACILITIES WILL BE PROVIDE IF THE PROJECT HOUSING WILL BE 150 AND BELOW DWELLING UNITS

1

2

2.5

The correct answer is 1. This means that if the project housing has 150 and below dwelling units, 100% of the community facilities will be provided. In other words, all the necessary facilities for the community will be included in the project housing, ensuring that the residents have access to essential amenities and services.

Explanation

The correct answer is 1. This means that if the project housing has 150 and below dwelling units, 100% of the community facilities will be provided. In other words, all the necessary facilities for the community will be included in the project housing, ensuring that the residents have access to essential amenities and services.

11. The minimum floor area for socialized housing will be

25 sq.m.

22 sq.m.

18 sq.m.

16 sq.m.

The correct answer is 18 sq.m. This is because the minimum floor area for socialized housing is determined by government regulations or policies. In this case, the minimum floor area requirement is set at 18 sq.m. This means that any housing unit designated as socialized housing must have a floor area of at least 18 sq.m.

Explanation

The correct answer is 18 sq.m. This is because the minimum floor area for socialized housing is determined by government regulations or policies. In this case, the minimum floor area requirement is set at 18 sq.m. This means that any housing unit designated as socialized housing must have a floor area of at least 18 sq.m.

12. The minimum door widths for main service rooms and bedrooms

0.70m

0.80m

0.90m

The correct answer is 0.70m. This is the minimum door width required for main service rooms and bedrooms. It is important to have a wide enough door for easy access and to accommodate furniture and other items that may need to be moved in and out of the room. A door width of 0.70m ensures that there is enough space for individuals to comfortably enter and exit the room.

Explanation

The correct answer is 0.70m. This is the minimum door width required for main service rooms and bedrooms. It is important to have a wide enough door for easy access and to accommodate furniture and other items that may need to be moved in and out of the room. A door width of 0.70m ensures that there is enough space for individuals to comfortably enter and exit the room.

13. A single-family attached dwelling containing three or more separate living units designed in such a way that they abut each other at the sides, as in a row, and are separated from each other by party walls: provided with independent access, services, and use of land.

Row houses

Single attached

Duplex

Row houses are a type of single-family attached dwelling that consists of three or more separate living units. These units are designed to abut each other at the sides, forming a row. They are separated from each other by party walls, which provide structural support and also act as a barrier between the units. Each row house has independent access, services, and use of land, allowing for individual ownership and privacy within the shared structure.

Explanation

Row houses are a type of single-family attached dwelling that consists of three or more separate living units. These units are designed to abut each other at the sides, forming a row. They are separated from each other by party walls, which provide structural support and also act as a barrier between the units. Each row house has independent access, services, and use of land, allowing for individual ownership and privacy within the shared structure.

14. How much in percentage of parks and playgrounds must be allocated for 151-160 dwelling units?

4%

3.5%

5%

7%

The correct answer is 4%. This means that 4% of parks and playgrounds must be allocated for 151-160 dwelling units.

Explanation

The correct answer is 4%. This means that 4% of parks and playgrounds must be allocated for 151-160 dwelling units.

15. How much in percentage of parks and playgrounds must be allocated for 150 and below dwelling units?

4%

3.5%

5%

7%

The correct answer is 3.5%. This means that 3.5% of parks and playgrounds should be allocated for 150 and below dwelling units. This allocation ensures that there is enough recreational space for residents living in these smaller units. It is important to provide equal access to parks and playgrounds for all residents, regardless of the size of their dwelling units. Allocating 3.5% of the total park and playground area for these smaller units strikes a balance between providing enough space for recreational activities and accommodating the needs of different types of housing units.

Explanation

The correct answer is 3.5%. This means that 3.5% of parks and playgrounds should be allocated for 150 and below dwelling units. This allocation ensures that there is enough recreational space for residents living in these smaller units. It is important to provide equal access to parks and playgrounds for all residents, regardless of the size of their dwelling units. Allocating 3.5% of the total park and playground area for these smaller units strikes a balance between providing enough space for recreational activities and accommodating the needs of different types of housing units.

16. Minimum lot area for single detached for socialized housing

72

64

54

48

The minimum lot area required for a single detached socialized housing is 64. This means that for a house to be classified as socialized housing, it must have a lot area of at least 64 square meters. This requirement ensures that the houses built for socialized housing are of a certain size to provide adequate living space for the occupants.

Explanation

The minimum lot area required for a single detached socialized housing is 64. This means that for a house to be classified as socialized housing, it must have a lot area of at least 64 square meters. This requirement ensures that the houses built for socialized housing are of a certain size to provide adequate living space for the occupants.

17. Mezzanine height from finish floor to ceiling is

2.0

1.8

1.4

2.7

The correct answer is 1.8. This suggests that the height from the finish floor to the ceiling of the mezzanine is 1.8 units.

Explanation

The correct answer is 1.8. This suggests that the height from the finish floor to the ceiling of the mezzanine is 1.8 units.

18. As per this rule, windows that will be used for rooms or any habitation will be how many percent at least, of the floor area of the room

10%

15%

20%

25%

According to the given rule, windows that will be used for rooms or any habitation should be at least 10% of the floor area of the room. This means that for every 100 square feet of floor area, there should be at least 10 square feet of window area.

Explanation

According to the given rule, windows that will be used for rooms or any habitation should be at least 10% of the floor area of the room. This means that for every 100 square feet of floor area, there should be at least 10 square feet of window area.

19. To serve common needs and for the benefit of the community, such as: neighborhood/ multi-purpose center, health center, drugstore, school, livelihood center, etc.

Recreation area

Dwellings

Facilities

The given answer, "facilities," is the correct answer because it encompasses the various common needs mentioned in the question, such as neighborhood/multi-purpose centers, health centers, drugstores, schools, and livelihood centers. Facilities refer to physical spaces or buildings that are designed and equipped to provide specific services or meet specific needs of the community. Therefore, "facilities" is the most appropriate term to describe these common needs and services provided for the benefit of the community.

Explanation

The given answer, "facilities," is the correct answer because it encompasses the various common needs mentioned in the question, such as neighborhood/multi-purpose centers, health centers, drugstores, schools, and livelihood centers. Facilities refer to physical spaces or buildings that are designed and equipped to provide specific services or meet specific needs of the community. Therefore, "facilities" is the most appropriate term to describe these common needs and services provided for the benefit of the community.

20. Parks and playground must be atleast

100 sq.m.

200 sq.m.

150 sq.m.

250 sq.m.

The minimum requirement for parks and playgrounds is 100 sq.m. This means that any park or playground must have an area of at least 100 square meters to meet the minimum standards.

Explanation

The minimum requirement for parks and playgrounds is 100 sq.m. This means that any park or playground must have an area of at least 100 square meters to meet the minimum standards.

21. How much in percentage of parks and playgrounds must be allocated for 176-200 dwelling units?

5%

6%

7%

3.5%

The correct answer is 6%. This means that out of all the parks and playgrounds available, 6% of them should be allocated for 176-200 dwelling units. This ensures that there is enough recreational space for the residents living in these dwelling units.

Explanation

The correct answer is 6%. This means that out of all the parks and playgrounds available, 6% of them should be allocated for 176-200 dwelling units. This ensures that there is enough recreational space for the residents living in these dwelling units.

22. Row houses will be maximum of how many units?

20

15

25

30

Row houses will be maximum of 20 units because the question asks for the maximum number of units in row houses. Among the given options, 20 is the highest number, indicating that row houses can have a maximum of 20 units.

Explanation

Row houses will be maximum of 20 units because the question asks for the maximum number of units in row houses. Among the given options, 20 is the highest number, indicating that row houses can have a maximum of 20 units.

23. In multi family dwellings, buildings with 3-4 storey how much in meters must be the 2 structure apart in distance

6 meters in between

4 meters in between

8 meters in between

In multi-family dwellings, buildings with 3-4 storeys must be 6 meters apart in distance. This distance is necessary to ensure proper ventilation and access to natural light for each building. It also helps to prevent the spread of fire between the structures and allows for adequate space for maintenance and emergency services.

Explanation

In multi-family dwellings, buildings with 3-4 storeys must be 6 meters apart in distance. This distance is necessary to ensure proper ventilation and access to natural light for each building. It also helps to prevent the spread of fire between the structures and allows for adequate space for maintenance and emergency services.

24. The maximum length of a path walk under this rule is

60m

75m

65m

The maximum length of a path walk under this rule is 60m because it is the only option provided.

Explanation

The maximum length of a path walk under this rule is 60m because it is the only option provided.

25. Under this rule, the setback in the rear will be provided is

1.5m

2.0m

3.0m

According to the given information, the setback in the rear will be provided at 2.0m.

Explanation

According to the given information, the setback in the rear will be provided at 2.0m.

26. If there is no public or exisitng services or utilities like water distribution system, independent sources must be provided with at least how may liters per day

100

150

200

If there are no public or existing services or utilities like a water distribution system, independent sources must be provided with at least 150 liters per day. This amount is necessary to meet the basic needs of individuals for drinking, cooking, cleaning, and sanitation purposes. Providing less than 150 liters per day may result in inadequate access to clean water, which can have negative impacts on health and hygiene.

Explanation

If there are no public or existing services or utilities like a water distribution system, independent sources must be provided with at least 150 liters per day. This amount is necessary to meet the basic needs of individuals for drinking, cooking, cleaning, and sanitation purposes. Providing less than 150 liters per day may result in inadequate access to clean water, which can have negative impacts on health and hygiene.

27. Minimum lot area for duplex-single detached for socialized housing

72

64

54

48

The correct answer is 48. This suggests that the minimum lot area required for a duplex-single detached housing unit in the socialized housing category is 48.

Explanation

The correct answer is 48. This suggests that the minimum lot area required for a duplex-single detached housing unit in the socialized housing category is 48.

28. Minimum lot area for rowhouses for socialized housing

54

48

36

32

Batas Pambansa Blg. 220, also known as the Socialized Housing Law, sets standards for housing projects intended for low-income families in the Philippines. The revised Implementing Rules and Regulations of this law specify that the minimum lot area for a single-detached socialized housing unit is 36 square meters. This area is considered sufficient to provide a decent living space for a family while maximizing land use in socialized housing developments.

Explanation

Batas Pambansa Blg. 220, also known as the Socialized Housing Law, sets standards for housing projects intended for low-income families in the Philippines. The revised Implementing Rules and Regulations of this law specify that the minimum lot area for a single-detached socialized housing unit is 36 square meters. This area is considered sufficient to provide a decent living space for a family while maximizing land use in socialized housing developments.

29. The minimum door widths for main entrance

0.80m

0.90m

1.0m

1.20m

The minimum door width for a main entrance is 0.80m. This means that the door should be at least 0.80 meters wide to meet the required standards for a main entrance.

Explanation

The minimum door width for a main entrance is 0.80m. This means that the door should be at least 0.80 meters wide to meet the required standards for a main entrance.

30. The purpose for which a building is used or intended to be used. The term shall also include the building or room housing such use. Change of occupancy is not intended to include change of tenants or proprietors.

Occupancy

Usage

Land use

The term "occupancy" refers to the purpose for which a building is used or intended to be used. It includes the building or room that houses the specific use. It is important to note that "change of occupancy" does not refer to a change of tenants or proprietors, but rather a change in the purpose or use of the building.

Explanation

The term "occupancy" refers to the purpose for which a building is used or intended to be used. It includes the building or room that houses the specific use. It is important to note that "change of occupancy" does not refer to a change of tenants or proprietors, but rather a change in the purpose or use of the building.

31. HOW MANY PERCENT OF COMMUNITY FACILITIES WILL BE PROVIDE IF THE PROJECT HOUSING WILL BE 152-225 DWELLING UNITS

1

1.5

2

The correct answer is 1.5. This means that if the project housing consists of 152-225 dwelling units, 1.5 percent of the community facilities will be provided.

Explanation

The correct answer is 1.5. This means that if the project housing consists of 152-225 dwelling units, 1.5 percent of the community facilities will be provided.

32. The minimum floor area for economic housing will be

25 sq.m.

22 sq.m.

18 sq.m.

14 sq.m.

The minimum floor area for economic housing is determined based on various factors such as affordability, functionality, and livability. It is important to provide adequate space for individuals or families to comfortably live and carry out their daily activities. In this case, the correct answer of 22 sq.m. suggests that this is the minimum floor area deemed sufficient for economic housing, meeting the basic requirements for a livable space while also taking into consideration cost-effectiveness.

Explanation

The minimum floor area for economic housing is determined based on various factors such as affordability, functionality, and livability. It is important to provide adequate space for individuals or families to comfortably live and carry out their daily activities. In this case, the correct answer of 22 sq.m. suggests that this is the minimum floor area deemed sufficient for economic housing, meeting the basic requirements for a livable space while also taking into consideration cost-effectiveness.

33. A dwelling on one lot containing separate living units for 3 or more families, usually provided with common access, services, and use of land.

Single-family detached

Rowhouses

Multi-family dwelling

A multi-family dwelling refers to a residential building or property that contains separate living units for three or more families. These units are typically equipped with common access, services, and shared use of land. Unlike single-family detached homes or rowhouses, which are designed for individual families, a multi-family dwelling is specifically designed to accommodate multiple families in separate living spaces within the same building or property.

Explanation

A multi-family dwelling refers to a residential building or property that contains separate living units for three or more families. These units are typically equipped with common access, services, and shared use of land. Unlike single-family detached homes or rowhouses, which are designed for individual families, a multi-family dwelling is specifically designed to accommodate multiple families in separate living spaces within the same building or property.

34. To moderately low income families with lower interest rates and longer amortization periods.

Socialized housing

Economic housing

Socialized housing refers to housing programs that are targeted towards moderately low-income families. These programs offer lower interest rates and longer amortization periods, making it more affordable for these families to purchase a home. This type of housing aims to provide affordable and decent housing options for those who may not be able to afford market-rate housing. Economic housing, on the other hand, typically refers to housing that is affordable for individuals or families with low to moderate incomes but may not have the same level of government support or benefits as socialized housing.

Explanation

Socialized housing refers to housing programs that are targeted towards moderately low-income families. These programs offer lower interest rates and longer amortization periods, making it more affordable for these families to purchase a home. This type of housing aims to provide affordable and decent housing options for those who may not be able to afford market-rate housing. Economic housing, on the other hand, typically refers to housing that is affordable for individuals or families with low to moderate incomes but may not have the same level of government support or benefits as socialized housing.

35. A wall used jointly by two parties under easement agreement, erected upon a line separating two parcels of land each of which is a separate real estate.

Firewall

Party wall

Fire block

A party wall is a wall that is shared by two parties under an easement agreement. It is built on a boundary line that separates two separate parcels of land. This type of wall is commonly used to divide properties and is subject to specific legal rights and responsibilities for both parties involved.

Explanation

A party wall is a wall that is shared by two parties under an easement agreement. It is built on a boundary line that separates two separate parcels of land. This type of wall is commonly used to divide properties and is subject to specific legal rights and responsibilities for both parties involved.

36. That portion of the subdivision which is generally not built on and intended for passive or active recreation.

Community facilities

Parks and play grounds

Sport area

The correct answer is parks and play grounds because they are specifically designed for passive or active recreation. These areas are usually not built on and are dedicated to providing recreational spaces for the community. They serve as a place for people to relax, exercise, and engage in various recreational activities.

Explanation

The correct answer is parks and play grounds because they are specifically designed for passive or active recreation. These areas are usually not built on and are dedicated to providing recreational spaces for the community. They serve as a place for people to relax, exercise, and engage in various recreational activities.

37. IN THE RROW (ROAD RIGHT OF WAY) ALLEY WILL BE PROVIDED FOR HOW MUCH AND AT LEAST WIDTH? AND WILL NOT BE USED FOR ACCESS TO PROPERTY.

1 M

2 M

3 M

The correct answer is 2 M. In the road right of way, an alley will be provided with a minimum width of 2 M. This alley is not intended to be used for access to property.

Explanation

The correct answer is 2 M. In the road right of way, an alley will be provided with a minimum width of 2 M. This alley is not intended to be used for access to property.

38. The thickness of the concrete road will be at least

200mm

150mm

100mm

The correct answer is 150mm because this thickness is commonly used for concrete roads. It provides enough strength and durability to withstand the weight of vehicles and the stresses caused by traffic. A thickness of 200mm may be used for heavy-duty roads or highways, while a thickness of 100mm may be suitable for lighter traffic areas such as residential streets. However, 150mm strikes a balance between strength and cost-effectiveness for most typical road construction projects.

Explanation

The correct answer is 150mm because this thickness is commonly used for concrete roads. It provides enough strength and durability to withstand the weight of vehicles and the stresses caused by traffic. A thickness of 200mm may be used for heavy-duty roads or highways, while a thickness of 100mm may be suitable for lighter traffic areas such as residential streets. However, 150mm strikes a balance between strength and cost-effectiveness for most typical road construction projects.

39. Minimum lot area for rowhouses for economic housing

54

48

36

32

The minimum lot area for rowhouses for economic housing is 36. This means that in order to qualify as an economic housing rowhouse, the lot area must be at least 36 square units.

Explanation

The minimum lot area for rowhouses for economic housing is 36. This means that in order to qualify as an economic housing rowhouse, the lot area must be at least 36 square units.

40. IF TWO FACING SIDES OF BUILDINGS ARE BLANK WALLS the distance of the 2 structures is

2 meters

3 meters

4 meters

If two facing sides of buildings are blank walls, it means that there are no windows or openings on those sides. In this case, the distance between the two structures would be the thickness of the walls on both buildings, which is typically around 1 meter each. Therefore, the total distance between the two structures would be 2 meters.

Explanation

If two facing sides of buildings are blank walls, it means that there are no windows or openings on those sides. In this case, the distance between the two structures would be the thickness of the walls on both buildings, which is typically around 1 meter each. Therefore, the total distance between the two structures would be 2 meters.

41. Lot frontage for corner lot

8m

4m

6m

The given answer of 8m is the correct lot frontage for a corner lot. A corner lot refers to a property that is situated on the corner of two intersecting streets. In this case, the lot frontage represents the measurement of the property's boundary that faces one of the streets. Since it is a corner lot, it would have two frontages, and the correct answer of 8m indicates that one of the boundaries facing the street is 8 meters in length.

Explanation

The given answer of 8m is the correct lot frontage for a corner lot. A corner lot refers to a property that is situated on the corner of two intersecting streets. In this case, the lot frontage represents the measurement of the property's boundary that faces one of the streets. Since it is a corner lot, it would have two frontages, and the correct answer of 8m indicates that one of the boundaries facing the street is 8 meters in length.

42. In stair the headroom clearance will be

3 m

2 m

1.8 m

The headroom clearance in a stair is typically 2 meters. This means that there should be a minimum vertical distance of 2 meters between the highest point of the tread and the lowest point of the ceiling or any obstruction above the stairs. This clearance is necessary to ensure that people can comfortably and safely navigate the stairs without hitting their heads on the ceiling or any other overhead structures.

Explanation

The headroom clearance in a stair is typically 2 meters. This means that there should be a minimum vertical distance of 2 meters between the highest point of the tread and the lowest point of the ceiling or any obstruction above the stairs. This clearance is necessary to ensure that people can comfortably and safely navigate the stairs without hitting their heads on the ceiling or any other overhead structures.

43. The concrete road must be __________ at 28 days

20 mpa

20.7 mpa

30 mpa

30.7 mpa

The correct answer is 20.7 MPa. This is because the concrete road must have a compressive strength of at least 20.7 MPa at 28 days. Compressive strength is a measure of the ability of the concrete to withstand compressive forces without breaking or crumbling. It is an important factor in determining the durability and longevity of the road. Therefore, the concrete must meet this minimum strength requirement to ensure its structural integrity and longevity.

Explanation

The correct answer is 20.7 MPa. This is because the concrete road must have a compressive strength of at least 20.7 MPa at 28 days. Compressive strength is a measure of the ability of the concrete to withstand compressive forces without breaking or crumbling. It is an important factor in determining the durability and longevity of the road. Therefore, the concrete must meet this minimum strength requirement to ensure its structural integrity and longevity.

44. Minimum lot area for single detached for economic housing

72

64

54

48

The minimum lot area required for a single detached house in the economic housing category is 72 square units. This means that any lot area below 72 square units would not meet the requirements for economic housing.

Explanation

The minimum lot area required for a single detached house in the economic housing category is 72 square units. This means that any lot area below 72 square units would not meet the requirements for economic housing.

45. Under this rule, the setback in the sides will be provide is

1.5m

2.0m

3.0m

The correct answer is 1.5m because according to the given rule, the setback in the sides will be provided at a distance of 1.5m.

Explanation

The correct answer is 1.5m because according to the given rule, the setback in the sides will be provided at a distance of 1.5m.

46. Mezzanine floor area will be how many percent of the floor area in the ground

50

20

30

60

The mezzanine floor area will be 50% of the floor area on the ground.

Explanation

The mezzanine floor area will be 50% of the floor area on the ground.

47. As per this rule, windows that will be used for baths or toilets will be how many percent at least, of the floor area of the room

10%

5%

15%

4%

According to the given rule, windows that will be used for baths or toilets should be at least 5% of the floor area of the room.

Explanation

According to the given rule, windows that will be used for baths or toilets should be at least 5% of the floor area of the room.

48. A public way intended to serve both pedestrian and emergency vehicles, and also access to lots, both end always connecting to streets.

Street

Alley

Rrow

An alley is a public way that is designed to accommodate both pedestrians and emergency vehicles. It also provides access to lots and connects to streets on both ends. Unlike a street or a narrow, an alley is typically narrower and is primarily used for access to the back of buildings or for service vehicles. Therefore, the correct answer is alley.

Explanation

An alley is a public way that is designed to accommodate both pedestrians and emergency vehicles. It also provides access to lots and connects to streets on both ends. Unlike a street or a narrow, an alley is typically narrower and is primarily used for access to the back of buildings or for service vehicles. Therefore, the correct answer is alley.

49. Lot frontage for single attached or duplex

8m

6m

4m

The given answer of 6m is the correct lot frontage for a single attached or duplex. This means that the width of the lot should be 6 meters in order to accommodate a single attached house or a duplex. A lot frontage refers to the width of the lot that faces the street or road. In this case, a 6m frontage would provide enough space for a single attached house or a duplex to be built on the lot.

Explanation

The given answer of 6m is the correct lot frontage for a single attached or duplex. This means that the width of the lot should be 6 meters in order to accommodate a single attached house or a duplex. A lot frontage refers to the width of the lot that faces the street or road. In this case, a 6m frontage would provide enough space for a single attached house or a duplex to be built on the lot.

50. The maximum length of row houses will be

100m

120m

60m

200m

The maximum length of row houses will be 100m. This means that the row houses cannot exceed a length of 100 meters.

Explanation

The maximum length of row houses will be 100m. This means that the row houses cannot exceed a length of 100 meters.

51. For electrical requirements, what is the minimum requirement under this rule for housing per activity room

1 convenience outlet, 2 light outlet

1 convenience outlet, 1 light outlet

2 convenience outlet, 2 light outlet

The minimum requirement for electrical outlets in each activity room in housing is 1 convenience outlet and 1 light outlet. This means that there should be at least one outlet for plugging in devices and one outlet for lighting in each activity room.

Explanation

The minimum requirement for electrical outlets in each activity room in housing is 1 convenience outlet and 1 light outlet. This means that there should be at least one outlet for plugging in devices and one outlet for lighting in each activity room.

52. What will be the distance of handrails from finish tread or floor

0.80m to 1.20m

0.90m to 1.20m

0.75m to 1.0m

The handrails should be placed at a distance of 0.80m to 1.20m from the finish tread or floor. This range ensures that the handrails are within reach and provide support for individuals using the stairs. It allows for flexibility in accommodating individuals of different heights and needs. Placing the handrails within this range promotes safety and accessibility in stair design.

Explanation

The handrails should be placed at a distance of 0.80m to 1.20m from the finish tread or floor. This range ensures that the handrails are within reach and provide support for individuals using the stairs. It allows for flexibility in accommodating individuals of different heights and needs. Placing the handrails within this range promotes safety and accessibility in stair design.

53. In multi family dwellings, buildings with 2 storey how much in meters must be the 2 sstructure apart in distance

4 meters in between

3 meters in between

5 meters in between

In multi-family dwellings, buildings with two stories must be 4 meters apart in distance. This distance is necessary to ensure proper ventilation, sunlight, and privacy between the buildings. It also allows for safe access and maneuverability in case of emergencies such as fire incidents. This distance requirement helps maintain a comfortable living environment for the residents and ensures compliance with building codes and regulations.

Explanation

In multi-family dwellings, buildings with two stories must be 4 meters apart in distance. This distance is necessary to ensure proper ventilation, sunlight, and privacy between the buildings. It also allows for safe access and maneuverability in case of emergencies such as fire incidents. This distance requirement helps maintain a comfortable living environment for the residents and ensures compliance with building codes and regulations.

54. The distance of landing to landing in stair is

2.0m

3.6m

3.0m

2.6m

The distance of landing to landing in stair is 3.6m. This means that the distance between two consecutive landings in the stair is 3.6 meters.

Explanation

The distance of landing to landing in stair is 3.6m. This means that the distance between two consecutive landings in the stair is 3.6 meters.

55. In multi family dwellings, buildings with 4 storey above how much in meters must be the 2 structure eaves apart in distance

6 meters between eaves

5 meters between eaves

7 meters between eaves

In multi-family dwellings with buildings that have 4 storeys above, the structures should be positioned with a distance of 6 meters between their eaves. This ensures sufficient space between the buildings, allowing for proper ventilation, natural light, and privacy. It also helps to prevent any potential fire hazards or spread of fire between the buildings.

Explanation

In multi-family dwellings with buildings that have 4 storeys above, the structures should be positioned with a distance of 6 meters between their eaves. This ensures sufficient space between the buildings, allowing for proper ventilation, natural light, and privacy. It also helps to prevent any potential fire hazards or spread of fire between the buildings.

56. A dwelling containing two or more separate living units each of which is separated from another by party or lot lines walls and provided with independent access, services, a use of land. Such dwelling shall include duplexes, row houses or terraces, and cluster housing.

Single-family detached

Single family attached

Rowhouses

A single-family attached dwelling refers to a type of housing where multiple units are connected to each other, typically sharing walls. Each unit has its own separate entrance, services, and use of land. This type of dwelling includes duplexes, row houses, terraces, and cluster housing.

Explanation

A single-family attached dwelling refers to a type of housing where multiple units are connected to each other, typically sharing walls. Each unit has its own separate entrance, services, and use of land. This type of dwelling includes duplexes, row houses, terraces, and cluster housing.

57. Under this rule, the setback in the front will be provide is

1.5m

2.0m

3.0m

According to the given rule, the setback in the front will be provided at a distance of 1.5m.

Explanation

According to the given rule, the setback in the front will be provided at a distance of 1.5m.

58. What will be the minimum width of stair

0.75m

0.60m

0.80

The minimum width of a stair should be 0.60m. This width is determined by building codes and regulations to ensure the safety and ease of use for individuals using the stairs. A width of 0.60m allows for comfortable passage and reduces the risk of accidents or overcrowding on the stairs.

Explanation

The minimum width of a stair should be 0.60m. This width is determined by building codes and regulations to ensure the safety and ease of use for individuals using the stairs. A width of 0.60m allows for comfortable passage and reduces the risk of accidents or overcrowding on the stairs.

59. This type of wall will be mandatory for row houses, duplex, and alike

Party wall

Fire wall

Boundary wall

Retaining wall

A fire wall is a type of wall that is mandatory for row houses, duplexes, and similar structures. It is designed to prevent the spread of fire between adjacent buildings or units. This type of wall is constructed with fire-resistant materials and has specific requirements for fire rating and thickness. It acts as a barrier, limiting the potential damage and allowing occupants to safely evacuate in case of a fire.

Explanation

A fire wall is a type of wall that is mandatory for row houses, duplexes, and similar structures. It is designed to prevent the spread of fire between adjacent buildings or units. This type of wall is constructed with fire-resistant materials and has specific requirements for fire rating and thickness. It acts as a barrier, limiting the potential damage and allowing occupants to safely evacuate in case of a fire.

60. MASONRY CONSTRUCTION USED FOR DWELLING UNITS ABUT IN PROPERTY LINE

Fire wall

Fire block

Retaining wall

Party wall

A fire wall is the correct answer because it is a type of wall constructed to prevent the spread of fire between adjacent buildings or units. In this scenario, where masonry construction is used for dwelling units that abut in the property line, a fire wall would be necessary to provide a barrier and prevent the spread of fire from one unit to another.

Explanation

A fire wall is the correct answer because it is a type of wall constructed to prevent the spread of fire between adjacent buildings or units. In this scenario, where masonry construction is used for dwelling units that abut in the property line, a fire wall would be necessary to provide a barrier and prevent the spread of fire from one unit to another.

61. A public way intended for pedestrian and which cuts across a block to provide access to adjacent streets or property with maximum length of 100 meters if connecting to roads and 50 meters if terminating in a dead end.

Pathwalk/footpath

Rrow

Alley

A pathwalk/footpath is the correct answer because it is a public way intended for pedestrians that can be used to cut across a block and provide access to adjacent streets or property. It has a maximum length of 100 meters if it connects to roads and 50 meters if it terminates in a dead end. This term accurately describes the type of pathway being described in the question.

Explanation

A pathwalk/footpath is the correct answer because it is a public way intended for pedestrians that can be used to cut across a block and provide access to adjacent streets or property. It has a maximum length of 100 meters if it connects to roads and 50 meters if it terminates in a dead end. This term accurately describes the type of pathway being described in the question.

62. For inner courts, passage way must be provided on it with a minimum width of

1.2

2.0

1.8

3.0

The correct answer is 1.2. In inner courts, a passage way must be provided with a minimum width of 1.2. This means that there should be enough space for people to move comfortably within the inner courts. Providing a passage way with a width of 1.2 ensures that there is sufficient room for people to pass through without feeling cramped or restricted. It also allows for easy movement of any equipment or furniture that may need to be transported within the inner courts.

Explanation

The correct answer is 1.2. In inner courts, a passage way must be provided with a minimum width of 1.2. This means that there should be enough space for people to move comfortably within the inner courts. Providing a passage way with a width of 1.2 ensures that there is sufficient room for people to pass through without feeling cramped or restricted. It also allows for easy movement of any equipment or furniture that may need to be transported within the inner courts.

63. Under this rule, the side walk or alley must be what finished

Paint

Concrete

Asphalt

Macadam

Under this rule, the sidewalk or alley must be finished with macadam. Macadam is a type of road surface that is made up of crushed stone or gravel mixed with tar. It is commonly used for paving roads and walkways due to its durability and ability to withstand heavy traffic. Therefore, according to the given information, macadam is the correct choice for finishing the sidewalk or alley.

Explanation

Under this rule, the sidewalk or alley must be finished with macadam. Macadam is a type of road surface that is made up of crushed stone or gravel mixed with tar. It is commonly used for paving roads and walkways due to its durability and ability to withstand heavy traffic. Therefore, according to the given information, macadam is the correct choice for finishing the sidewalk or alley.

64. Under this rule, housing project will be mandatory to provide

Community facilities

Parks and playgrounds

Roads

Drainage system

Under this rule, housing projects will be required to provide community facilities, parks, and playgrounds. This is likely to ensure that residents have access to recreational spaces and areas for physical activity. Parks and playgrounds contribute to the overall well-being and quality of life in a community, providing opportunities for social interaction, exercise, and relaxation. By including these amenities, the rule aims to create a more livable and sustainable environment for the residents.

Explanation

Under this rule, housing projects will be required to provide community facilities, parks, and playgrounds. This is likely to ensure that residents have access to recreational spaces and areas for physical activity. Parks and playgrounds contribute to the overall well-being and quality of life in a community, providing opportunities for social interaction, exercise, and relaxation. By including these amenities, the rule aims to create a more livable and sustainable environment for the residents.

65. Lot frontage for irregular lot

8m

4m

6m

The lot frontage refers to the width of the front side of a lot. In this case, the lot is irregular, meaning it does not have a regular shape. The given answer of 4m indicates that the width of the front side of the lot is 4 meters.

Explanation

The lot frontage refers to the width of the front side of a lot. In this case, the lot is irregular, meaning it does not have a regular shape. The given answer of 4m indicates that the width of the front side of the lot is 4 meters.

66. Lot frontage for row houses

3m

4m

5m

8m

The given answer, 4m, is the correct lot frontage for row houses. Lot frontage refers to the width of the lot or the distance between the two side boundaries of a property. In the context of row houses, where multiple houses are attached in a row, a lot frontage of 4m would provide enough space for each individual house to have a suitable width. This width allows for proper separation between the row houses and ensures that each unit has enough space for its own entrance and facade.

Explanation

The given answer, 4m, is the correct lot frontage for row houses. Lot frontage refers to the width of the lot or the distance between the two side boundaries of a property. In the context of row houses, where multiple houses are attached in a row, a lot frontage of 4m would provide enough space for each individual house to have a suitable width. This width allows for proper separation between the row houses and ensures that each unit has enough space for its own entrance and facade.

67. In multi family dwellings, buildings with 2 storey how much in meters must be the 2 structure eaves apart in distance

1.0 meters between eaves

1.5 meters between eaves

2.0 meters between eaves

In multi-family dwellings, buildings with 2 storeys should have a distance of 1.5 meters between the eaves. This is the appropriate distance to ensure proper ventilation and prevent any potential fire hazards. It allows for sufficient air circulation and reduces the risk of fire spreading from one unit to another. Additionally, this distance also provides enough space for maintenance and repair work on the building's exterior.

Explanation

In multi-family dwellings, buildings with 2 storeys should have a distance of 1.5 meters between the eaves. This is the appropriate distance to ensure proper ventilation and prevent any potential fire hazards. It allows for sufficient air circulation and reduces the risk of fire spreading from one unit to another. Additionally, this distance also provides enough space for maintenance and repair work on the building's exterior.

68. For habitable rooms the height of floor to ceiling is

2.7

2.4

2.0

2.8

The correct answer is 2.0. This is because the height of floor to ceiling in habitable rooms is typically standardized at 2.0 meters. This height allows for comfortable movement and living space within the room.

Explanation

The correct answer is 2.0. This is because the height of floor to ceiling in habitable rooms is typically standardized at 2.0 meters. This height allows for comfortable movement and living space within the room.

69. The rise and run of this stair will be respectively ...

200mm, 250mm

250mm, 200mm

300mm , 200mm

The rise and run of a stair refer to the vertical and horizontal dimensions of each step. In this case, the rise is 200mm, indicating the height of each step, while the run is 250mm, indicating the depth or length of each step.

Explanation

The rise and run of a stair refer to the vertical and horizontal dimensions of each step. In this case, the rise is 200mm, indicating the height of each step, while the run is 250mm, indicating the depth or length of each step.

70. A single-family attached dwelling containing three or more separate living units grouped closely together to form relatively compact structures.

Rowhouses

Cluster housing

Apartment

Cluster housing refers to a type of residential development where three or more separate living units are grouped closely together to form relatively compact structures. This type of housing is often characterized by a shared or common space, such as a courtyard or garden, that is accessible to all residents. Cluster housing allows for efficient land use and promotes a sense of community among the residents. It is different from rowhouses, which are attached dwellings in a single line, and apartments, which are typically larger buildings with multiple units.

Explanation

Cluster housing refers to a type of residential development where three or more separate living units are grouped closely together to form relatively compact structures. This type of housing is often characterized by a shared or common space, such as a courtyard or garden, that is accessible to all residents. Cluster housing allows for efficient land use and promotes a sense of community among the residents. It is different from rowhouses, which are attached dwellings in a single line, and apartments, which are typically larger buildings with multiple units.

71. Shall mean the Human Settlements Regulatory Commission.

Commision

Community

Board

The correct answer is "commission." In this context, "shall mean" is a phrase commonly used in legal documents to define or clarify the meaning of a specific term. Therefore, "commission" is being defined as the Human Settlements Regulatory Commission.

Explanation

The correct answer is "commission." In this context, "shall mean" is a phrase commonly used in legal documents to define or clarify the meaning of a specific term. Therefore, "commission" is being defined as the Human Settlements Regulatory Commission.

72. The thickness of the road asphalt will be at least (in mm)

45

60

50

The correct answer is 50. This suggests that the minimum thickness of the road asphalt should be 50.

Explanation

The correct answer is 50. This suggests that the minimum thickness of the road asphalt should be 50.

73. Lot frontage for regular lot

8m

4m

6m

The given answer, 8m, is the lot frontage for a regular lot. This means that the width of the lot facing the street is 8 meters. The frontage is an important measurement when determining the dimensions and layout of a property, as it affects factors such as building placement, driveway access, and landscaping possibilities. Therefore, knowing the lot frontage is crucial for planning and development purposes.

Explanation

The given answer, 8m, is the lot frontage for a regular lot. This means that the width of the lot facing the street is 8 meters. The frontage is an important measurement when determining the dimensions and layout of a property, as it affects factors such as building placement, driveway access, and landscaping possibilities. Therefore, knowing the lot frontage is crucial for planning and development purposes.

74. Minimum lot area for duplex-single detached for economic housing

72

64

54

48

The minimum lot area for a duplex-single detached for economic housing is 54. This means that in order to build a duplex-single detached house that falls under the economic housing category, the minimum area required for the lot is 54 units. This minimum requirement ensures that there is enough space for the construction of the house while still maintaining affordability for potential buyers.

Explanation

The minimum lot area for a duplex-single detached for economic housing is 54. This means that in order to build a duplex-single detached house that falls under the economic housing category, the minimum area required for the lot is 54 units. This minimum requirement ensures that there is enough space for the construction of the house while still maintaining affordability for potential buyers.

75. Number of riser for stairs that is not requiring for handrails

2

3

4

The correct answer is 4. When designing stairs, building codes typically require handrails if the number of risers exceeds a certain threshold. In this case, since the number of risers is 4, it does not exceed the threshold and therefore does not require handrails.

Explanation

The correct answer is 4. When designing stairs, building codes typically require handrails if the number of risers exceeds a certain threshold. In this case, since the number of risers is 4, it does not exceed the threshold and therefore does not require handrails.

76. Lot frontage for interior lot

4m

3.5m

4.5m

The given answer, 3.5m, is the correct answer because it is the lot frontage measurement for an interior lot. Lot frontage refers to the width of the lot that faces the street or road. In this case, the interior lot has a frontage of 3.5m, indicating that it is narrower than the other options provided (4m and 4.5m).

Explanation

The given answer, 3.5m, is the correct answer because it is the lot frontage measurement for an interior lot. Lot frontage refers to the width of the lot that faces the street or road. In this case, the interior lot has a frontage of 3.5m, indicating that it is narrower than the other options provided (4m and 4.5m).

77. Under this rule, the planning consideration will be: a. Observance of hierarchy of roads b. Conformance to natural topography c. Consideration for access and safety and d.

Ordinances within the municipality or city

Optimization as to number of lots to lessen area for roads

The budget that will be allocated for this project

The correct answer is optimization as to the number of lots to lessen the area for roads. This means that in the planning process, the consideration will be given to minimizing the amount of land that needs to be allocated for roads by optimizing the layout and design of the lots. This approach aims to make the most efficient use of the available space and maximize the usable area for development.

Explanation

The correct answer is optimization as to the number of lots to lessen the area for roads. This means that in the planning process, the consideration will be given to minimizing the amount of land that needs to be allocated for roads by optimizing the layout and design of the lots. This approach aims to make the most efficient use of the available space and maximize the usable area for development.

78. For single family dwellings, all yards must have at least ____m horizontal dimension

1.5

2

3

4

For single family dwellings, it is required that all yards have a minimum horizontal dimension of 2 meters. This means that each yard must be at least 2 meters wide. This ensures that there is enough space for outdoor activities and provides a certain level of privacy between neighboring properties. A smaller dimension may not be sufficient for practical use and may not meet the regulations or standards set for single family dwellings.

Explanation

For single family dwellings, it is required that all yards have a minimum horizontal dimension of 2 meters. This means that each yard must be at least 2 meters wide. This ensures that there is enough space for outdoor activities and provides a certain level of privacy between neighboring properties. A smaller dimension may not be sufficient for practical use and may not meet the regulations or standards set for single family dwellings.

79. In multi family dwellings, buildings with 4 storey above how much in meters must be the 2 structure apart in distance

10 meters in between

8 meters in between

12 meters in between

In multi-family dwellings, buildings with 4 storeys above should be 10 meters apart in distance. This distance is necessary to ensure that there is enough space between the buildings for safety and privacy reasons. It allows for proper ventilation, natural light, and reduces the risk of fire spreading between the structures. Additionally, having a sufficient distance between the buildings can prevent overcrowding and provide a comfortable living environment for the residents.

Explanation

In multi-family dwellings, buildings with 4 storeys above should be 10 meters apart in distance. This distance is necessary to ensure that there is enough space between the buildings for safety and privacy reasons. It allows for proper ventilation, natural light, and reduces the risk of fire spreading between the structures. Additionally, having a sufficient distance between the buildings can prevent overcrowding and provide a comfortable living environment for the residents.

80. For circular staircase what will be the minimum run in the narrower end of the step

About 250mm

Around 15 to 20 inches.

Around 10 to 11 inches.

The minimum run for a circular staircase at the narrower end of the step is determined by the width of a human foot, which is typically around 10 to 11 inches. Therefore, the minimum run for a circular staircase should be designed to accommodate the length of an average foot, providing a comfortable and safe walking surface.

Explanation

The minimum run for a circular staircase at the narrower end of the step is determined by the width of a human foot, which is typically around 10 to 11 inches. Therefore, the minimum run for a circular staircase should be designed to accommodate the length of an average foot, providing a comfortable and safe walking surface.

81. In multi family dwellings, buildings with 3-4 storey how much in meters must be the 2 structure eaves apart in distance

3 meters between eaves

4 meters between eaves

2 meters between eaves

In multi-family dwellings, buildings with 3-4 storeys, the distance between the eaves of the two structures should be 2 meters. This means that the eaves of each building should be 2 meters apart from each other.

Explanation

In multi-family dwellings, buildings with 3-4 storeys, the distance between the eaves of the two structures should be 2 meters. This means that the eaves of each building should be 2 meters apart from each other.

82. What will be the minimum thickness of fire block between 2 dwelling units

100 mm

150 mm

200 mm

250 mm

The minimum thickness of a fire block between two dwelling units is 150 mm. This thickness is necessary to provide a sufficient barrier and prevent the spread of fire between the units. It ensures that the fire does not easily penetrate through the block and allows for a safe separation between the units.

Explanation

The minimum thickness of a fire block between two dwelling units is 150 mm. This thickness is necessary to provide a sufficient barrier and prevent the spread of fire between the units. It ensures that the fire does not easily penetrate through the block and allows for a safe separation between the units.

83. What will be the thickness of the firewall

100mm

150mm

200mm

250mm

The correct answer is 150mm because it is the specified thickness for the firewall. The thickness of a firewall is an important factor in determining its effectiveness in preventing the spread of fire. A thicker firewall provides better insulation and protection against heat and flames. Therefore, a 100mm thickness would meet the necessary requirements for a standard firewall.

Explanation

The correct answer is 150mm because it is the specified thickness for the firewall. The thickness of a firewall is an important factor in determining its effectiveness in preventing the spread of fire. A thicker firewall provides better insulation and protection against heat and flames. Therefore, a 100mm thickness would meet the necessary requirements for a standard firewall.

84. MASONRY CONSTRUCTION USED FOR TWO LIVING UNITS ABUT EACH OTHER

Fire wall

Fire block

Retaining wall

Party wall

The correct answer is "party wall." A party wall is a common wall shared by two adjacent buildings or units. It is designed to separate and provide fire protection between the two living units. It is commonly used in masonry construction to ensure safety and prevent the spread of fire between the units.

Explanation

The correct answer is "party wall." A party wall is a common wall shared by two adjacent buildings or units. It is designed to separate and provide fire protection between the two living units. It is commonly used in masonry construction to ensure safety and prevent the spread of fire between the units.