Targetcast Networks Installation Certification
(58).webp "Targetcast Networks Installation Certification - Quiz")
This test will cover aspects of the Installation process. Please answer all questions to the best of your ability. You may use the Installation SOW to complete the test. You must pass with a score of 85 or higher. Once you pass the test, you will need to copy or print your certificate. Good Luck!
Questions and Answers
- 1.
The tech will physically install the Targetcasters (TC's) to the TV before assigning them to the site via the Targetcast Networks Installer Application.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The tech must assign the targetcasters to the site before installing them. The generic ads and settings will be utilized until assigned. NOTE: The Targetcasters will not update unless you power cycle the unit after making a settings change.Rate this question:
-
- 2.
When a tech is installing a HD TC, what resolution must the tech set the Set Top Box to?
- A.
480P
- B.
2000BC
- C.
1080i
- D.
720P
Correct Answer
D. 720PExplanation
The tech must set the Set Top Box to a resolution of 720P when installing a HD TC.Rate this question:
-
- 3.
The tech will use only the front panel of the HD Set Top Box to set the resolution that the TC needs to operate on.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
Using the front panel to change the resolution is a temporary fix and the only way to lock the resolution in is by going into the menu. The HD STB's will broadcast channels in various formatsRate this question:
-
- 4.
From the selections below, what is the first part of the install that the tech will complete first?
- A.
Deliverables
- B.
Installing the Targecasters(TC's)
- C.
Networking/Install Router
- D.
Install the Flux Capacitor
- E.
Inventory Equipment
Correct Answer
E. Inventory EquipmentExplanation
The tech will complete the inventory of equipment before starting any other installation tasks. This is because it is important to have a clear understanding of the available equipment and its condition before proceeding with the installation process. By completing the inventory first, the tech can ensure that all necessary equipment is present and in working order, avoiding any delays or issues during the installation.Rate this question:
-
- 5.
Which of the following is not a required tool?
- A.
Screwdrivers
- B.
6' and 8' Ladders
- C.
Laptop
- D.
Glass Cutter
- E.
RG6 Crimpers and Strippers
Correct Answer
D. Glass CutterExplanation
The glass cutter is not a required tool because it is not commonly used in most general tasks or projects. Screwdrivers are essential for various tasks involving screws, ladders are needed for reaching high places, a laptop is commonly used for work or personal tasks, and RG6 crimpers and strippers are necessary for working with RG6 cables. However, a glass cutter is a specialized tool used specifically for cutting glass, which is not a common requirement in most situations.Rate this question:
-
- 6.
Targetcast Networks will provide Black Ty Wraps, Velcro, Surge Protectors, and F Connectors.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The statement is false because there is no mention of Targetcast Networks providing any specific items such as Black Ty Wraps, Velcro, Surge Protectors, and F Connectors. Therefore, we cannot conclude that Targetcast Networks will provide these items.Rate this question:
-
- 7.
The tech must check in with Targetcast once he/she arrives on site and not the project management team.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The tech must check in with a Member of the Project Management Team and not Targetcast.Rate this question:
-
- 8.
All Targetcasters (TC's) can be determined by type by looking at the bottom of the unit. Which below would describe a HD Non Tuner?
- A.
DCAST 9.2 x 6
- B.
DCAST 10.1
- C.
DCAST 9.2 x10
- D.
DCAST 90210
Correct Answer
B. DCAST 10.1Explanation
The correct answer is "DCAST 10.1". This is because the question asks for a HD Non Tuner, and out of the given options, "DCAST 10.1" is the only one that fits this description. The other options either do not mention HD or are not Non Tuner units.Rate this question:
-
- 9.
The router must be installed in the managers office at all times.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The router will need to be installed in a central location to all TC'sRate this question:
-
- 10.
Sites that have the netgear router will connect the Cat5e cable coming from the stores network and connect to the Wan port of TCN's Netgear Router.
- A.
TRUE
- B.
FALSE
Correct Answer
A. TRUEExplanation
The statement is true because it states that sites with the Netgear router will connect the Cat5e cable from the store's network and connect it to the WAN port of TCN's Netgear Router. This implies that the Netgear router is being used as a central point of connection for the sites, allowing them to connect to the TCN network.Rate this question:
-
- 11.
What website address will the tech use to assign the Targetcasters to the Venue?
- A.
Http://www.mcdonalds.com
- B.
Http://www.apache.com
- C.
Https://peapod.targetcastnetworks.com/install/login
- D.
Https://prod.targetcastnetworks.com/install/login
- E.
Https://targetcast.prodnetworks.com/install/login
Correct Answer
D. Https://prod.targetcastnetworks.com/install/loginExplanation
The tech will use the website address "https://prod.targetcastnetworks.com/install/login" to assign the Targetcasters to the Venue.Rate this question:
-
- 12.
During the Router install, the tech will need to connect to the TCN Router through the wireless capabilites of the laptop. What SSID will you connect to? This applies to all sites that will utilize a TCN Router.
- A.
Tmobile hotspot
- B.
Boingo
- C.
Applebees
- D.
Tcnwifi
- E.
Free wifi
Correct Answer
D. TcnwifiExplanation
During the router install, the technician will need to connect to the TCN Router through the wireless capabilities of the laptop. Therefore, the SSID that the technician will connect to is "tcnwifi."Rate this question:
-
- 13.
The tech will use the serial numbers on the side of the targetcaster(TC) to assign the unit to the site.
- A.
TRUE
- B.
FALSE
Correct Answer
A. TRUEExplanation
The statement is true because the tech will use the serial numbers on the side of the targetcaster (TC) to assign the unit to the site. This means that each unit will have a unique serial number that can be used to identify and associate it with a specific site. By using these serial numbers, the tech can ensure that the units are correctly assigned and installed in the appropriate locations.Rate this question:
-
- 14.
What is the TCN Site ID #?
- A.
The store number.
- B.
A combination of the store number and the address.
- C.
The address
- D.
A unique number to each site that is used to assign targetcasters to.
Correct Answer
D. A unique number to each site that is used to assign targetcasters to.Explanation
The TCN Site ID # is a unique number assigned to each site. This number is used to assign targetcasters to their respective sites. It is not the store number or the address, but rather a specific identifier for each site.Rate this question:
-
- 15.
What location on the TV should the Targetcast Logo be installed?
- A.
Top Center
- B.
Bottom Right
- C.
Bottom Center
- D.
Top Right
- E.
Anywhere on the front of the TV
Correct Answer
B. Bottom RightExplanation
The tech will need to assign the TC's to the site VIA the Installer Application prior to installing them.Rate this question:
-
- 16.
When a tech is installing a Tuner on a TV, the tech will always use a tuner cable even if you can't change the video input by pressing a button on the TV itself.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The tech will install a Tuner Cable only if the TV has a button to change the video input. If the TV does not have a Video button, the tech will install RF Modulators.Rate this question:
-
- 17.
Which item below is not a key focal point of installing a Targetcast Tuner?
- A.
The Power Plug must reach an outlet (Power Strip may be required)
- B.
The black IR must reach the front edge of the TV and stick out about a ¼”
- C.
The input and output connections must reach as well.
- D.
The Tuner must be connected to the stores fax machine.
- E.
TCN would prefer you to use Black Ty-Wraps to secure the TC’s to the TV
Correct Answer
D. The Tuner must be connected to the stores fax machine.Explanation
The correct answer is "The Tuner must be connected to the stores fax machine." This is because the other options mention specific requirements for installing a Targetcast Tuner, such as ensuring that the power plug reaches an outlet, the black IR reaches the front edge of the TV, and the input and output connections are properly connected. However, there is no mention of the Tuner needing to be connected to the store's fax machine, making it the odd one out and not a key focal point of the installation process.Rate this question:
-
- 18.
When Installing a Non Tuner, The White banded Non Tuner Cable is connected to the TV and the Black banded cable connects to the video source.
- A.
TRUE
- B.
False
Correct Answer
A. TRUEExplanation
The correct answer is TRUE. When installing a non-tuner, the white banded non-tuner cable is connected to the TV and the black banded cable connects to the video source. This means that the white cable carries the signal from the TV to the non-tuner device, while the black cable carries the signal from the video source to the non-tuner device. This setup allows for proper transmission of audio and video signals between the TV and the non-tuner device.Rate this question:
-
- 19.
Please select the correct answer that describes the proper order to resize the TV screen once the TC is installed.
- A.
Vid Width. Vid Top, Vid Left, Vid, Height
- B.
Vid Left, Vid Top, Vid Width, Vid Height
- C.
Vid Left, Vid Top, Vid Left, Vid Height
- D.
Vid Height, Vid Left, Vid Top, Vid Width
Correct Answer
B. Vid Left, Vid Top, Vid Width, Vid Height -
- 20.
The tech should wait until he/she is on site before they read through the SOW to fimiliarize themselves with it.
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The Tech must read through the SOW before arriving on site.Rate this question:
-
- 21.
What does STB stand for?
- A.
Single Truck Box
- B.
Signal Transmit Box
- C.
Special Trained Brain
- D.
Set Top Box
- E.
Simple Tackle Belt
Correct Answer
D. Set Top BoxExplanation
The correct answer is "Set Top Box". A Set Top Box (STB) is a device that connects to a television and allows users to access digital television services. It is commonly used to receive and decode digital television signals, providing access to various channels and interactive features.Rate this question:
-
- 22.
What does HD stand for?
- A.
Hard Drive
- B.
Hell Defined
- C.
High Definition
- D.
Highly Disliked
- E.
Handy Dandy
Correct Answer
C. High DefinitionExplanation
HD stands for High Definition. This term is commonly used in the context of video and audio technology to describe a higher level of image or sound quality. High Definition refers to a resolution that is significantly sharper and more detailed than standard definition. It typically involves a higher number of pixels, resulting in a clearer and more vibrant viewing experience.Rate this question:
-
- 23.
What does SD stand for
- A.
Strange Definition
- B.
Standard Decline
- C.
Standard Definition
- D.
Single Double
- E.
None of the above
Correct Answer
C. Standard DefinitionExplanation
SD stands for Standard Definition. This refers to the resolution of a video or image, typically used in older television systems. Standard Definition has a lower resolution compared to High Definition (HD) and Ultra High Definition (UHD), providing a lower quality image or video.Rate this question:
-
- 24.
What will the tech leave the store once the install is complete?
- A.
2 remotes and the box of trash
- B.
A laminated operation/troubleshooting guide and all extra materials.
- C.
2 remotes and a laminated operation/troubleshooting.guide
- D.
A partridge in a pair tree
- E.
Nothing At All.
Correct Answer
C. 2 remotes and a laminated operation/troubleshooting.guideExplanation
Once the installation is complete, the technician will leave the store with 2 remotes and a laminated operation/troubleshooting guide.Rate this question:
-
- 25.
The tech must install red Do Not Remove tags at both ends of the power supply and network cable of the TCN Router.
- A.
TRUE
- B.
FALSE
Correct Answer
A. TRUEExplanation
The installation of red Do Not Remove tags at both ends of the power supply and network cable of the TCN Router is necessary. These tags serve as a visual reminder to not remove the cables, ensuring that the power supply and network connection remain intact and secure. This helps to prevent any accidental disconnection or damage to the router, ensuring its proper functioning.Rate this question:
-
- 26.
Where will the URL https://prod.targetcastnetworks.com/install/login take you?
- A.
McDonalds Installation School.
- B.
Targetcast Networks Internal Server.
- C.
Targetcast Networks Installer Application.
- D.
Installation Services.
- E.
None of the above.
Correct Answer
C. Targetcast Networks Installer Application.Explanation
The URL "https://prod.targetcastnetworks.com/install/login" will take you to the Targetcast Networks Installer Application. This is indicated by the URL itself, which includes "targetcastnetworks.com/install/login", suggesting that it is a login page for an installer application related to Targetcast Networks.Rate this question:
-
- 27.
To access the Targetcasters (TC's) Status Menu, which button sequence below will be used on the TCN remote control?
- A.
TV > REW > PLAY
- B.
VCR > VCR > PLAY
- C.
VCR > PLAY
- D.
TV > VCR > PLAY
- E.
All of the above
Correct Answer
C. VCR > PLAYExplanation
The correct answer is VCR > PLAY. This sequence is used to access the Targetcasters (TC's) Status Menu on the TCN remote control. The other button sequences mentioned in the options do not correspond to accessing the TC's Status Menu.Rate this question:
-
- 28.
In order to see the Downloading or Uploading Progress once the TC has power applied, what setting below allows you to see this on the TV screen?
- A.
Display Disable set to NO
- B.
RF Blaster set to 2
- C.
Wifi Config set to ON
- D.
Display Disable set to YES
- E.
None of the above
Correct Answer
A. Display Disable set to NOExplanation
Setting the "Display Disable" option to "NO" allows you to see the Downloading or Uploading Progress on the TV screen once the TC has power applied.Rate this question:
-
- 29.
When Installing HD Non-Tuners and you are setting up the Video Source and Video Output in the Installer Application, what settings should you utilize at all times
- A.
Component/Component
- B.
Component/Composite
- C.
Cable/Composite
- D.
Call Tech Support for answer
Correct Answer
A. Component/ComponentExplanation
When installing HD Non-Tuners and setting up the Video Source and Video Output in the Installer Application, the settings that should be utilized at all times are Component/Component. This means that the video source should be connected using component cables and the video output should also be set to component. Component cables provide a higher quality video signal compared to composite cables, and using the same component settings for both the source and output ensures compatibility and optimal video quality.Rate this question:
-
- 30.
If a TV is fed via a HDMI cable from a Set Top Box that is located behind the TV and you received HD Non-Tuners with Composite/Component Cable Harnesses, we must abort the Install and reschedule?
- A.
TRUE
- B.
FALSE
Correct Answer
B. FALSEExplanation
The correct answer is FALSE. The given scenario states that the TV is connected to a Set Top Box via an HDMI cable. It also mentions that the HD Non-Tuners are received with Composite/Component Cable Harnesses. However, there is no indication that these cable harnesses are necessary for the installation or that the HDMI connection is insufficient. Therefore, there is no need to abort the installation and reschedule.Rate this question:
-
- 31.
When adding the TC Serial Numbers into the Installer Application, you can enter more than one TC serial at a time?
- A.
TRUE
- B.
FALSE
Correct Answer
A. TRUEExplanation
In the Installer Application, it is possible to enter more than one TC serial number at a time. This feature allows for efficient and convenient input of multiple TC serial numbers without the need to enter them one by one.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Jun 28, 2023Quiz Edited by
ProProfs Editorial Team -
Apr 06, 2009Quiz Created by
Targetcast
- Binary Code Quizzes
- Computer Concept Quizzes
- Computer Essential Quizzes
- Computer Forensics Quizzes
- Computer Hardware Quizzes
- Computer Networking Quizzes
- Computer Parts Quizzes
- Computer Programming Quizzes
- Computer Science Quizzes
- Computer Security Quizzes
- Computer Shortcut Key Quizzes
- Computer Skills Quizzes
- Computer Virus Quizzes
- Cyber Security Quizzes
- Data Quizzes
- Data Security Quizzes
- Hacking Quizzes
- HCI Quizzes
- IT SecurITy Quizzes
- Malware Quizzes
- Microprocessor Quizzes
- Operating System Quizzes
- Phishing Quizzes
- Programming Language Quizzes
- Software Quizzes
Back to top