PeopleNet: Installation Questions Certification Test! Trivia Quiz

1. When using the VHB tape to secure the Internal Antenna, how must the area be prepared?

The area must be wiped clean using water and a shop rag

The area must be cleaned with Windex and a paper towel

Clean area where internal antenna will be mounted using the alcohol wipes. Wipe off the areas with a clean paper towel (Do not use a shop rag).

Explanation

Clean area where internal antenna will be mounted using the alcohol wipes. Wipe off the areas with a clean paper towel (Do not use a shop rag).

2. The onboard computer should be mounted using...

The double sided VHB Tape

2 Screws

4 Screws

The OBC does not need to be secured.

Secure a self-tapping screw in the four corner holes of the OBC. Tighten the self-tapping screws until the OBC is firmly mounted.

Explanation

Secure a self-tapping screw in the four corner holes of the OBC. Tighten the self-tapping screws until the OBC is firmly mounted.

3. When routing and handling PeopleNet Cables, you should avoid...

Routing cable close to heat sources such as the trucks exhaust system.

Pulling on the cable connections

Any locations that would result in pinching of the cable or the cable coming into contact with anything sharp.

All of the above.

Never pull on the cable connectors; pull only on the cable. Make sure the cables do not run within two and a half feet of the vehicle's stacks or other heat sources. Never coil the coaxial antenna cables, as this causes a choke coil. Never run cables in a manner that interferes with the driver's ability to safely operate the vehicle.

Explanation

Never pull on the cable connectors; pull only on the cable. Make sure the cables do not run within two and a half feet of the vehicle's stacks or other heat sources. Never coil the coaxial antenna cables, as this causes a choke coil. Never run cables in a manner that interferes with the driver's ability to safely operate the vehicle.

4. What should be done with any unused cable connections?

They should be cut off and the end of the cable shrink wrapped.

They should be wrapped in electrician's tape and stored safely out of the way.

They can be left as is and should be moved out of the way.

There should not be any unused cable connections in a basic OBC install.

Wrapping the unused connections keeps them clean and minimizes the risk of contacting +12V. These connections are grounded.

Explanation

Wrapping the unused connections keeps them clean and minimizes the risk of contacting +12V. These connections are grounded.

5. The GPS Antenna is capable of receiving signals through metal.

True

False

Check the top line to make sure GPS reads 3D and ANT reads OK. This indicates the OBC recognizes the GPS antenna and the signal is good. A. If GPS reads NO, check to make sure there is no metal overhanging the Antenna. B. If ANT reads NO or HI, make sure the GPS Antenna connection to the OBC is secure and not pinched.

Explanation

Check the top line to make sure GPS reads 3D and ANT reads OK. This indicates the OBC recognizes the GPS antenna and the signal is good. A. If GPS reads NO, check to make sure there is no metal overhanging the Antenna. B. If ANT reads NO or HI, make sure the GPS Antenna connection to the OBC is secure and not pinched.

6. Where should the power wires on the PeopleNet Display 4 Options cable be connected to the vehicle?

The black wire attaches to ignition (switch) and red attaches to the ground.

The black wire attaches to ground and the red attaches to constant power 12 volts.

The black wire attaches to constant power 12 volts and the red attaches to ignition (switch).

The black wire attaches to ground and the red attaches to ignition (switch).

not-available-via-ai

Explanation

not-available-via-ai

7. The vehicle engine must be running to properly check that engine data is being recognized by the PeopleNet System.

True

False

Turn the key to the on position, if you have not already done so, and allow it to idle for at least 30 seconds. The MBA does not start listening to the vehicle data until 30 seconds after the key is turned on.

Explanation

Turn the key to the on position, if you have not already done so, and allow it to idle for at least 30 seconds. The MBA does not start listening to the vehicle data until 30 seconds after the key is turned on.

8. Where should the Internal Antenna be mounted on the vehicle?

Antenna Assembly needs to be mounted horizontally with the mounting tape on the bottom

Antenna Assembly needs to be mounted as far forward in the cab as possible

No obstructions such as metal or metal foil above the antenna

All of the Above

• Antenna Assembly needs to be mounted horizontally with the mounting tape on the bottom • Antenna Assembly needs to be mounted as far forward in the cab as possible • No obstructions such as metal or metal foil above the antenna

Explanation

• Antenna Assembly needs to be mounted horizontally with the mounting tape on the bottom • Antenna Assembly needs to be mounted as far forward in the cab as possible • No obstructions such as metal or metal foil above the antenna

9. How should the power cables on the TABLET DC to DC converter be connected to vehicle power?

The red wire should be connected to the vehicle ignition (accessory) and the black wire to ground.

The red wire should be connected to the vehicle ignition (switched) and the black wire to ground.

The red wire should be connected to the ground and the black to constant power.

The red wire should be connected to constant power and the black to ground.

1. Using a butt connector, attach the red wire from the DC-DC Power Supply to the fuse holder. 2. Connect the other end of the fuse holder to a 15 Amp power source.

Explanation

1. Using a butt connector, attach the red wire from the DC-DC Power Supply to the fuse holder. 2. Connect the other end of the fuse holder to a 15 Amp power source.

10. When mounting the OBC, what is the recommended direction for the cable connections?

The OBC should be mounted so the cable connections are facing up.

He OBC should be mounted so the cable connections are facing the side

The OBC should be mounted so the cable connections are facing down.

It does not matter the direction the cable connections face.

The OBC must be mounted with the cable connections pointed horizontally or downward. This prevents moisture from entering the OBC through the connections.

Explanation

The OBC must be mounted with the cable connections pointed horizontally or downward. This prevents moisture from entering the OBC through the connections.

11. How do you check to make sure the PD4, BLU.2, Tablet, Blu and OBC are properly reading GPS and PerformX data?

Select System>>Settings>>OBC Data.

Select System>>Diagnostic>>Information>>Check OBC Data.

Turn the vehicle ignition off and select System>>OBC Diagnostic>>Diagnostic GPS then Diagnostic PerformX.

Turn the vehicle ignition on and select System>>OBC Diagnostic>>Diagnostic GPS then Diagnostic PerformX.

1. Start the vehicle's engine, if you have not already done so, and allow it to idle for at least 30 seconds. The MBA does not start listening to the vehicle data until 30 seconds after the key is turned on. 2. Select System on the Home Menu. 3. Select OBC Diagnostic, then Diagnostic Vehicle Management. 4. PerfromX should display Yes.

Explanation

1. Start the vehicle's engine, if you have not already done so, and allow it to idle for at least 30 seconds. The MBA does not start listening to the vehicle data until 30 seconds after the key is turned on. 2. Select System on the Home Menu. 3. Select OBC Diagnostic, then Diagnostic Vehicle Management. 4. PerfromX should display Yes.

12. What color wire on the Truck to VID Cable connects to the PTO line when connecting the Multi-Bus Adapter to the trucks PTO?

Grey

Blue

White

Black

Connect the gray wire on the Vehicle to VID Cable to the vehicle's PTO signal line.

Explanation

Connect the gray wire on the Vehicle to VID Cable to the vehicle's PTO signal line.

13. What is the blue barrel connector on the Main Cable used for?

The blue barrel connector is used to connect to the PerformX cable for collecting ECM data.

The blue barrel connector is used to connect to the Option cable which connects the OBC to the display.

The blue barrel connector is used to connect to the Satellite Modem.

The blue barrel connector is used to connect to the handset.

Connect the blue Options Cable connector to the blue connector on the Main Cable by pushing together and hand tightening.

Explanation

Connect the blue Options Cable connector to the blue connector on the Main Cable by pushing together and hand tightening.

14. When installing a Multi-Bus Adapter in a truck without a J1939 bus, what setting must you choose for the J1708 Port Configuration?

J1708 Bus

Multi-Bus Adaptor

DSA Interface

1. Set the Configure J1708 Port to Multi-Bus Adapter through the Driver Terminal, BLU, BLU.2, or TABLET display. a. Driver Terminal Instructions i. Select Menu and arrow down to OBC Administration. Press Select. ii. Enter 9238 in the Password Field. iii. Select Assign J1708 Port. iv. Select Multi-Bus Adapter. b. BLU, BLU.2, and TABLET Instructions i. Select System on the Home Menu. ii. Select OBC Diagnostic and arrow down to OBC Administration. Press Select. iii. Enter 9238 in the Password Field. iv. Select J1709 Port Configuration. v. Select Multi- Bus Adapter.

Explanation

1. Set the Configure J1708 Port to Multi-Bus Adapter through the Driver Terminal, BLU, BLU.2, or TABLET display. a. Driver Terminal Instructions i. Select Menu and arrow down to OBC Administration. Press Select. ii. Enter 9238 in the Password Field. iii. Select Assign J1708 Port. iv. Select Multi-Bus Adapter. b. BLU, BLU.2, and TABLET Instructions i. Select System on the Home Menu. ii. Select OBC Diagnostic and arrow down to OBC Administration. Press Select. iii. Enter 9238 in the Password Field. iv. Select J1709 Port Configuration. v. Select Multi- Bus Adapter.

15. What piece of hardware may be required to complete the PeopleNet Display 4 activation?

A Handset

A USB Keyboard

A USB drive to update Firmware

None of the above

Depending on the Firmware that is loaded on your device you may need to attach a USB Keyboard to complete activation.

Explanation

Depending on the Firmware that is loaded on your device you may need to attach a USB Keyboard to complete activation.

16. The GPS Antenna is a Push and Twist BNC Connection to the On Board Computer.

True

False

The statement is true because a GPS antenna typically uses a push and twist BNC (Bayonet Neill–Concelman) connection to connect to the on-board computer. This type of connection ensures a secure and reliable connection between the antenna and the computer, preventing any accidental disconnections.

Explanation

The statement is true because a GPS antenna typically uses a push and twist BNC (Bayonet Neill–Concelman) connection to connect to the on-board computer. This type of connection ensures a secure and reliable connection between the antenna and the computer, preventing any accidental disconnections.

17. What cable connection should you check if the g3 Downloader is failing or the On-Board Computer DSN is not appearing in the activation screen?

Power connection to the Display

The 44 Pin Connector

The connection of the Option Cable to the Main cable.

The connection of the Option Cable to the vehicle power supply.

The 44 Pin Connector should be checked because it is likely responsible for the failure of the g3 Downloader and the absence of the On-Board Computer DSN in the activation screen.

Explanation

The 44 Pin Connector should be checked because it is likely responsible for the failure of the g3 Downloader and the absence of the On-Board Computer DSN in the activation screen.

18. What color barrel connector does the Multi-Bus VID to Main cable connect to?

Blue

Black

Red

Grey

The Multi-Bus Adaptor, Universal and Paccar Cable all use the Red Barrel Connector to pass engine data to the PeopleNet Onboard Computer.

Explanation

The Multi-Bus Adaptor, Universal and Paccar Cable all use the Red Barrel Connector to pass engine data to the PeopleNet Onboard Computer.

19. How can you identify the TABLET is properly seated in the Docking Station?

The left docking station light will be illuminated.

The right docking station light will be flashing.

The right docking station light will be illuminated.

The TABLET will display sinking with OBC on the screen.

The right light indicates whether or not the TABLET is docked correctly. 1. Solid light TABLET is properly docked. 2. Flashing light TABLET is improperly docked.

Explanation

The right light indicates whether or not the TABLET is docked correctly. 1. Solid light TABLET is properly docked. 2. Flashing light TABLET is improperly docked.

20. After installing the Multi-bus Adapter Kit, you do not need to make any program changes through the display.

True

False

The only time you will need to make a change to the J1708 Port Configuration is when you are using a Straight PerformX Cable.

Explanation

The only time you will need to make a change to the J1708 Port Configuration is when you are using a Straight PerformX Cable.

21. What should be done with the terminating resistor when installing the two pin Multi-Bus Adapter Kit?

The terminating resistor should be left connected to the J1939 cable.

The terminating resistor can be discarded once the VID to truck connector is connected the J1939 vehicle connection.

The terminating resistor must be connected to the connector on the VID to truck cable.

The terminating resistor should be placed on the J1708 data bus cable.

Place the Terminating Resistor into the remaining J1939 connector on the Vehicle to VID cable. The J1939 system requires the Terminating Resistor to prevent stray signals from contaminating the data on the J1939 bus.

Explanation

Place the Terminating Resistor into the remaining J1939 connector on the Vehicle to VID cable. The J1939 system requires the Terminating Resistor to prevent stray signals from contaminating the data on the J1939 bus.

22. How can you identify the TABLET Docking Station is receiving adequate power?

Both the green left and right docking station lights will be illuminated.

The left green light on the docking station will be illuminated.

The right green light on the docking station will be illuminated.

The left green light on the docking station will flash repeatedly.

The left light indicates the Docking Station is receiving power. 1. Solid light Docking Station is receiving consistent power. 2. Flashing or no light Docking Station is not receiving consistent power.

Explanation

The left light indicates the Docking Station is receiving power. 1. Solid light Docking Station is receiving consistent power. 2. Flashing or no light Docking Station is not receiving consistent power.

23. The Cell Phone Antenna Connection is a Twist and Lock BNC connector.

True

False

The statement is false because a Twist and Lock BNC connector is not used for cell phone antenna connections. Cell phone antennas typically use SMA connectors or other types of connectors specifically designed for mobile devices.

Explanation

The statement is false because a Twist and Lock BNC connector is not used for cell phone antenna connections. Cell phone antennas typically use SMA connectors or other types of connectors specifically designed for mobile devices.

24. When completing a PeopleNet Display 4 upgrade from Driver Terminal, what process must be followed to ensure the device is activated properly?

The process is the same as installing a new On Board Computer with a BLU.2 Display.

The BLU activation process synchronizes the BLU to the OBC and activates both the OBC and BLU on the PeopleNet System. 1. BLU displays "Would you like to process an installation?". Select Yes. 2. BLU displays "Is this a new installation?". Select Yes. 3. The BLU displays the next installation screen requesting your Installer ID, Truck Number, and DSN Number (device serial number). a. Enter your Installer ID in the text box labeled Installer ID. Press Tab. b. Enter the Truck Number in the text box labeled Truck Number. Press Tab. c. BLU displays the OBC DSN below the Submit button. Make sure the OBC DSN matches the DSN in the vehicle. 4. Press Submit. BLU places a data call to complete activation. a. If the 2nd green LED stops flashing and the screen has not changed, press Data Call to continue the installation. 5. The screen changes and displays a message confirming a successful installation. a. Once you receive the installation confirmation message, the BLU activation is complete.

Explanation

The BLU activation process synchronizes the BLU to the OBC and activates both the OBC and BLU on the PeopleNet System. 1. BLU displays "Would you like to process an installation?". Select Yes. 2. BLU displays "Is this a new installation?". Select Yes. 3. The BLU displays the next installation screen requesting your Installer ID, Truck Number, and DSN Number (device serial number). a. Enter your Installer ID in the text box labeled Installer ID. Press Tab. b. Enter the Truck Number in the text box labeled Truck Number. Press Tab. c. BLU displays the OBC DSN below the Submit button. Make sure the OBC DSN matches the DSN in the vehicle. 4. Press Submit. BLU places a data call to complete activation. a. If the 2nd green LED stops flashing and the screen has not changed, press Data Call to continue the installation. 5. The screen changes and displays a message confirming a successful installation. a. Once you receive the installation confirmation message, the BLU activation is complete.

25. How should the wires on the wiring harness be connected to the vehicle power connections?

Red

Black

White

Properly connecting the OBC to power is critical to a successful installation. The OBC requires the following power connections: Red wire: constant +12 volts. White wire: ignition switched +12 volts, do not connect to accessory. Black wire: ground connection and cable shielding. If these wire connection are improperly completed, the OBC will not operate properly. For example, wiring the white wire to accessory or constant power prevents the OBC from properly recording ignition onIoff events. This impacts the OBC's location and engine data recording functions.

Explanation

Properly connecting the OBC to power is critical to a successful installation. The OBC requires the following power connections: Red wire: constant +12 volts. White wire: ignition switched +12 volts, do not connect to accessory. Black wire: ground connection and cable shielding. If these wire connection are improperly completed, the OBC will not operate properly. For example, wiring the white wire to accessory or constant power prevents the OBC from properly recording ignition onIoff events. This impacts the OBC's location and engine data recording functions.

Submit

26. When choosing a mounting location for the On-Board Computer you must follow these requirements.

The location must be at least one and half feet away from any heating components.

The location must not interfere with operation of the vehicle.

The location must remain dry at all times and provide a secure mount for the OBC.

The location must have adequate room so cables and connectors are not strained.

The location must be at least two and half feet away from any heating components.

The answer provides a comprehensive list of requirements that need to be followed when choosing a mounting location for the On-Board Computer (OBC). It states that the OBC must be mounted with the cable connections pointed horizontally or downward to prevent moisture from entering through the connections. The location must not interfere with the operation of the vehicle and must remain dry at all times. It should also provide a secure mount for the OBC and have adequate room to avoid straining cables and connectors. Additionally, it emphasizes that the location must be at least two and a half feet away from any heating components to ensure proper functioning of the OBC.

Explanation

The answer provides a comprehensive list of requirements that need to be followed when choosing a mounting location for the On-Board Computer (OBC). It states that the OBC must be mounted with the cable connections pointed horizontally or downward to prevent moisture from entering through the connections. The location must not interfere with the operation of the vehicle and must remain dry at all times. It should also provide a secure mount for the OBC and have adequate room to avoid straining cables and connectors. Additionally, it emphasizes that the location must be at least two and a half feet away from any heating components to ensure proper functioning of the OBC.

Submit