Lockout /Tag Out Quiz
-
Lockout/Tag out is a system used to ensure that equipment you’ve isolated and de-energized to work on remains shut down
-
True
-
False
-
About This Quiz
This quiz is related to GAS Lockout/Tag out procedure , please fill your name and press " Take Quiz" when you are ready.
(273).jpg "Lockout /Tag Out Quiz - Quiz")
Quiz Preview
- 2.
Lockout /Tag out procedure can be applied to ...
-
Circuits that receive energy from electrical power
-
Energy stored in springs
-
Potential energy from suspended parts
-
Hydraulic fluid under pressure
-
All Above
Correct Answer
A. All AboveExplanation
The lockout/tag out procedure can be applied to all the options mentioned above. It is a safety procedure used to ensure that hazardous energy sources are isolated and rendered inoperative before maintenance or servicing work is performed. This includes circuits that receive energy from electrical power, energy stored in springs, potential energy from suspended parts, and hydraulic fluid under pressure. By implementing lockout/tag out, workers are protected from unexpected release of energy and potential accidents.Rate this question:
-
- 3.
Work permit is NOT essential to perform any isolation for lockout/tag out.
-
True
-
False
Correct Answer
A. FalseExplanation
A work permit is essential to perform any isolation for lockout/tag out. Lockout/tag out procedures are used to ensure that equipment is properly isolated and de-energized before any maintenance or repair work is performed. A work permit is a document that authorizes and controls the work being done, and it includes information about the specific isolation procedures that need to be followed. Without a work permit, it would be unsafe to perform any isolation for lockout/tag out as there would be no formal authorization or control over the work being done. Therefore, the statement that a work permit is not essential for lockout/tag out is false.Rate this question:
-
- 4.
You know the equipment is safe when the power has been shut down
-
True
-
False
Correct Answer
A. FalseExplanation
The statement suggests that the equipment is safe only when the power has been shut down. However, this is not entirely true as there are other factors that determine the safety of the equipment. While shutting down the power is an important step in ensuring safety, there may be other hazards or risks associated with the equipment that need to be addressed. Therefore, the statement is false.Rate this question:
-
- 5.
Locks should be removed only by the person who installed them
-
True
-
False
Correct Answer
A. TrueExplanation
Locks should be removed only by the person who installed them to ensure security and prevent unauthorized access. By allowing only the installer to remove the locks, it ensures that only trusted individuals have control over access to the locked area or object. This helps maintain accountability and reduces the risk of tampering or unauthorized entry.Rate this question:
-
- 6.
Verifying isolation involves
-
Putting locks on the equipment
-
Putting a tag on the equipment
-
Attempting to turn the machine on
Correct Answer
A. Attempting to turn the machine onExplanation
The correct answer is "Attempting to turn the machine on" because verifying isolation requires checking if the equipment is truly isolated from its power source. This can be done by attempting to turn the machine on, as a successful start-up would indicate that the isolation has not been properly implemented. If the machine does not start, it confirms that the isolation measures are in place and effective. Putting locks and tags on the equipment are common isolation procedures, but they do not directly verify if the isolation has been achieved.Rate this question:
-
- 7.
Each work group (electrical, mechanical, instrument, analyzer, reliability, contractor) and the plant operation group shall install their own distinctive color locks
-
True
-
False
Correct Answer
A. TrueExplanation
The given statement is true because it states that each work group and the plant operation group shall install their own distinctive color locks. This means that each group will have their own unique color lock, making it easier to identify which group is responsible for a particular lock. This practice can help improve efficiency and organization in the workplace.Rate this question:
-
- 8.
After lockout or tagout devices have been removed by working employees or groups and isolation certificates and work permit are signed off, then
-
Operation can put their lock
-
Operation can't remove their lock
-
Operation can remove their lock
Correct Answer
A. Operation can remove their lockExplanation
After lockout or tagout devices have been removed by working employees or groups and isolation certificates and work permit are signed off, the operation can remove their lock. This means that the operation is allowed to remove the lockout or tagout device that was placed to ensure the safety of the equipment during maintenance or repair work. This indicates that the equipment is now safe to operate and the operation can proceed as normal.Rate this question:
-
- 9.
When electrical isolation or disconnect has to be carried, a certificate of electrical isolation shall be initiated in addition to ...
-
Work permit
-
Alarm event
-
Master card
Correct Answer
A. Master cardExplanation
When electrical isolation or disconnect needs to be carried out, a certificate of electrical isolation should be initiated in addition to the master card. The master card is likely a key or access card that grants permission to perform electrical isolation or disconnect. This card is necessary to ensure that only authorized personnel are able to carry out these procedures, maintaining safety and preventing any unauthorized access or accidents.Rate this question:
-
- 10.
The keys of Locks placed by authorized employee or group, must be kept in the office of ........ with proper identification
-
Operation Shift supervisor
-
Concern section supervisor
-
Maintenance Planning
Correct Answer
A. Concern section supervisorExplanation
The keys of locks placed by authorized employees or groups must be kept in the office of the concern section supervisor with proper identification. This is because the concern section supervisor is responsible for overseeing the specific section or area where the locks are placed. They have the knowledge and authority to ensure that the keys are properly stored and accounted for. By keeping the keys in their office, it allows for easy access and control over the locks, ensuring the security and integrity of the system.Rate this question:
-
- 11.
If key of lockout device is lost , authorized employee shall immediate fill the lost key report form and signed by authorized employee ....
-
Supervisor
-
Manger
-
Genral Manger
Correct Answer
A. SupervisorExplanation
If the key of a lockout device is lost, it is important for the authorized employee to immediately fill out a lost key report form. This form should then be signed by a supervisor. By involving a supervisor in the process, it ensures that there is oversight and accountability for the lost key. The supervisor can also take appropriate action to address the situation and ensure the security of the lockout device.Rate this question:
-
- 12.
After cutting the lock, key lost form shall be filed in .......... for record.
-
Authorized employee supervisor
-
Shift supervisor office
-
Safety supervisor
Correct Answer
A. Shift supervisor officeExplanation
After cutting the lock, the key lost form needs to be filed in the shift supervisor's office for record-keeping purposes. The shift supervisor is responsible for overseeing the operations during a specific shift and would have the necessary authority to handle such matters. Filing the form in the shift supervisor's office ensures that the incident is properly documented and can be addressed appropriately.Rate this question:
-
- 13.
Where a job requires more than one employee to accomplish, each employee shall hang his own lock and tag, in conjunction with ...
-
A gang-lock device
-
Multiple isolation form
-
Tag out
Correct Answer
A. A gang-lock deviceExplanation
A gang-lock device is the correct answer because it allows multiple employees to lock and tag out a piece of equipment or machinery together. This ensures that all employees involved in the job are aware of the lockout/tagout procedure and have control over the energy sources. By using a gang-lock device, each employee can hang their own lock and tag, indicating that they are actively working on the equipment and that it is not safe to operate. This helps prevent accidental startup or release of stored energy, ensuring the safety of all employees involved.Rate this question:
-
- 14.
According to GAS Lockout /Tag out procedure , the first lock should be installed by
-
Maintenance
-
Reliability
-
Operation
Correct Answer
A. OperationExplanation
According to the GAS Lockout/Tag out procedure, the first lock should be installed by the Operation department. This is because the Operation department is responsible for the day-to-day operation and maintenance of the equipment. They have the necessary knowledge and expertise to ensure that the equipment is properly locked out or tagged out to prevent any unexpected startup or release of energy. The Operation department is also typically the first point of contact when it comes to initiating maintenance or repair work, making it logical for them to be the ones to install the first lock.Rate this question:
-
- 15.
According to GAS Lockout /Tag out procedure , the last lock should be removed is
-
Maintenance Lock
-
Operation Lock
-
Affected employee lock
Correct Answer
A. Operation LockExplanation
According to the GAS Lockout/Tag out procedure, the last lock that should be removed is the Operation Lock. This lock is typically placed by the person who is responsible for operating the equipment or machinery. By removing this lock last, it ensures that all maintenance and repair work has been completed and that the equipment is safe to be operated again. Removing the Operation Lock before the other locks could potentially put the affected employee or others at risk if the equipment is not yet safe for use.Rate this question:
-
- 16.
Which of the following does not consider part of Lockout /Tag out system documentation & records?
-
Master LOTO Card
-
Lost Key Report Form
-
Isolation Certificate
-
Employee Job description
Correct Answer
A. Employee Job descriptionExplanation
The employee job description is not considered part of the Lockout/Tagout system documentation and records. The Lockout/Tagout system documentation and records typically include the Master LOTO Card, Lost Key Report Form, and Isolation Certificate. These documents are used to ensure the safety of employees by properly documenting and recording the lockout/tagout procedures and activities. The employee job description, on the other hand, describes the responsibilities and duties of an employee and is not directly related to the Lockout/Tagout system.Rate this question:
-
Quiz Review Timeline (Updated): Mar 21, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Jun 22, 2010Quiz Created by
Ahzahz
Back to top