Forney Air - Summer 2012
-
What color is the Forney packaging for the Tru-Flate coupler and plugs?
-
Red
-
Yellow
-
Blue
-
Green
-
The 'Forney Air - Summer 2012' quiz assesses knowledge on air tool maintenance and usage, focusing on Forney and Milton Industrial products. It covers identification, configuration, and operation of air supply components, essential for professionals in industrial settings.
.webp "Forney Air - Summer 2012 - Quiz")
Quiz Preview
- 2.
How many bands are used by Forney to identify a Milton Industrial coupler?
-
2 narrow
-
1 wide
-
1 narrow and 3 wide
-
1 narrow
Correct Answer
A. 2 narrowExplanation
Forney uses 2 narrow bands to identify a Milton Industrial coupler.Rate this question:
-
- 3.
What is the main purpose of an air hose?
-
To be tripped over by the boss
-
To allow a technician to look busy
-
To connect an air supply to a tool
-
To give a tool enough oil to work properly
Correct Answer
A. To connect an air supply to a toolExplanation
The main purpose of an air hose is to connect an air supply to a tool. This allows the tool to receive the necessary air pressure to operate effectively. The air hose acts as a conduit, delivering the compressed air from the source to the tool, enabling it to perform its intended function efficiently.Rate this question:
-
- 4.
What is the proper configuration of a Filter, Regulator, and Lubricator in an air supply line?
-
Filter Lubricator Regulator
-
Regulator Filter Lubricator
-
Filter Regulator Lubricator
-
It doesn't matter
Correct Answer
A. Filter Regulator LubricatorExplanation
The proper configuration of a Filter, Regulator, and Lubricator in an air supply line is to have the Filter first, followed by the Regulator, and then the Lubricator. The Filter is responsible for removing any impurities or contaminants from the air supply, ensuring clean and pure air. The Regulator controls the pressure of the air, allowing for consistent and safe operation of pneumatic tools or equipment. Finally, the Lubricator adds a small amount of oil to the compressed air, lubricating the tools and preventing wear and tear. This configuration ensures optimal performance and longevity of the equipment.Rate this question:
-
- 5.
What is the main purpose of an air Regulator?
-
To regulate the amount of oil introduced into the air line for tool lubrication
-
To regulate the amount of electricity to the motor for proper tank fill up
-
To regulate the air to turn a compressor on or off
-
To regulate the air for proper tool usage
Correct Answer
A. To regulate the air for proper tool usageExplanation
The main purpose of an air regulator is to regulate the air for proper tool usage. This means that the regulator controls the pressure of the air being delivered to the tool, ensuring that it is at the appropriate level for optimal performance and safety. By adjusting the regulator, the user can increase or decrease the air pressure to suit the specific requirements of the tool being used. This helps to prevent damage to the tool and allows for precise and efficient operation.Rate this question:
-
- 6.
When should a Lubricator not be used in the air supply line?
-
When using a paint spray gun
-
When you are out of oil
-
When you are using a Hi Speed chop saw
-
When your air tool starts making a buzzing sound
Correct Answer
A. When using a paint spray gunExplanation
A lubricator should not be used in the air supply line when using a paint spray gun because the oil from the lubricator can contaminate the paint and affect the quality of the finish. Lubricators are typically used to provide lubrication to pneumatic tools, but in the case of a paint spray gun, the presence of oil can cause issues such as uneven spray patterns or clogging of the nozzle. Therefore, it is recommended to avoid using a lubricator in the air supply line when using a paint spray gun to ensure a smooth and clean paint application.Rate this question:
-
- 7.
What does the unloader valve on an air pressure switch do?
-
Regulates air to tell the compressor to stop pumping
-
Regulates air to tell the compressor to start pumping
-
Releases air pressure in the main line from pump head to tank
-
It is a pressure relief valve to release excess pressure in the tank
Correct Answer
A. Releases air pressure in the main line from pump head to tankExplanation
The unloader valve on an air pressure switch releases air pressure in the main line from the pump head to the tank. This valve is responsible for ensuring that the pressure does not build up excessively in the main line, which could potentially cause damage to the system. By releasing the excess pressure, the unloader valve helps to maintain a safe and efficient operation of the compressor.Rate this question:
-
- 8.
If a compressor does not have a line to connect to the unloader valve, what should be done?
-
Make a line from plastic tubing
-
Nothing, the unloader valve is not used in this instance and the port can be left empty.
-
Get a different switch
-
Call Ghostbusters
Correct Answer
A. Nothing, the unloader valve is not used in this instance and the port can be left empty.Explanation
If a compressor does not have a line to connect to the unloader valve, it means that the unloader valve is not necessary for the operation of the compressor in this particular instance. Therefore, there is no need to make a line from plastic tubing, get a different switch, or call Ghostbusters. The port can be left empty without any negative impact on the compressor's functionality.Rate this question:
-
- 9.
Forney Industries offers 2 safety relief valves. On is preset at 150 PSI. What is the other preset pressure?
-
110 psi
-
120 psi
-
125 psi
-
130 psi
Correct Answer
A. 125 psiExplanation
Forney Industries offers 2 safety relief valves, one preset at 150 PSI and the other at 125 PSI.Rate this question:
-
- 10.
What is the optimum air pressure for most of our air tools?
-
120 psi
-
100 psi
-
90 psi
-
30 psi
Correct Answer
A. 90 psiExplanation
The optimum air pressure for most air tools is 90 psi. This is because air tools are designed to work efficiently and effectively at this pressure. Higher pressures can cause damage to the tool or create safety hazards, while lower pressures may result in insufficient power or performance. Therefore, maintaining a consistent air pressure of 90 psi is recommended for optimal operation of air tools.Rate this question:
-
- 11.
What does FRL stand for?
-
Forney Regulator Lubricator
-
Filter Regulator Lubricator
-
Front Range League
-
Filter Regulator Leg
Correct Answer
A. Filter Regulator LubricatorExplanation
FRL stands for Filter Regulator Lubricator. This is a commonly used term in industrial settings, particularly in pneumatic systems. An FRL unit is a combination of three components: a filter, which removes contaminants from the compressed air; a regulator, which controls the pressure of the air; and a lubricator, which adds oil to the air to lubricate the components. This combination is essential for ensuring the proper functioning and longevity of pneumatic equipment. Therefore, the correct answer is Filter Regulator Lubricator.Rate this question:
-
- 12.
What is the maximum amp draw used on a Forney air pressure switch?
-
12 amps
-
18 amps
-
20 amps
-
22 amps
Correct Answer
A. 20 ampsExplanation
The maximum amp draw used on a Forney air pressure switch is 20 amps.Rate this question:
-
- 13.
What type of pipe is preferred when plumbing for an air system?
-
Plastic
-
Galvanized Steel
-
Black Steel
-
Copper
Correct Answer
A. Black SteelExplanation
Black steel is the preferred type of pipe when plumbing for an air system because it is durable, strong, and resistant to corrosion. It can withstand high pressure and temperature conditions, making it suitable for air systems. Plastic pipes may not be able to handle the pressure and temperature requirements, while galvanized steel and copper pipes may be prone to corrosion over time. Therefore, black steel is the most suitable option for plumbing an air system.Rate this question:
-
- 14.
Where are Forney air products manufactured?
-
China
-
Italy
-
Turkey
-
USA
Correct Answer
A. ChinaExplanation
Forney air products are manufactured in China.Rate this question:
-
- 15.
Of the 4 styles of plugs and couplers we sell, which is the least popular?
-
Aro
-
Lincoln
-
Tru-Flate
-
Industrial Milton
Correct Answer
A. LincolnExplanation
The least popular style of plug and coupler among the four options provided is Lincoln.Rate this question:
-
- 16.
Why will the Lincoln plug not work with a universal coupler?
-
The plug is too long
-
The plug is too large in diameter
-
Lincoln is made by a different company
-
It has ¼” straight thread
Correct Answer
A. The plug is too longExplanation
The Lincoln plug will not work with a universal coupler because it is too long. The length of the plug is not compatible with the design or dimensions of the universal coupler, preventing them from being properly connected.Rate this question:
-
- 17.
Of the 4 hoses we sell, which stays flexible in very cold weather?
-
Rubber
-
PVC
-
Polyurethane Flex
-
Temperature is not a factor in flexibility
Correct Answer
A. Polyurethane FlexExplanation
Polyurethane Flex is the correct answer because it stays flexible in very cold weather. This suggests that it is able to withstand low temperatures without becoming stiff or rigid, unlike the other options (Rubber and PVC). This makes it a suitable choice for use in cold weather conditions where flexibility is important.Rate this question:
-
- 18.
If I want to use our pressure switch on a Hi Horsepower compressor, what should I look for?
-
Starter on motor
-
2 wires in old pressure switch
-
Amp draw on plate of the motor
-
All of the above
Correct Answer
A. All of the aboveExplanation
When wanting to use a pressure switch on a Hi Horsepower compressor, one should look for all of the above options. The starter on the motor is important as it helps in controlling the motor's electrical circuit. The presence of 2 wires in the old pressure switch is also significant as it indicates the switch's functionality. Additionally, checking the amp draw on the motor's plate is crucial as it provides information about the motor's power consumption. Therefore, considering all of these factors is necessary when using a pressure switch on a Hi Horsepower compressor.Rate this question:
-
- 19.
Why should I drain the water from my air compressor tank?
-
So the tank doesn't rust and it removes the moisture that can cause problems for air tools
-
So there is no pressure in the tank overnight
-
To remove any oil that may have leaked from the compressor pump
-
To let the motor and pump run longer to fill the tank
Correct Answer
A. So the tank doesn't rust and it removes the moisture that can cause problems for air toolsExplanation
Draining the water from the air compressor tank is necessary to prevent rusting and remove moisture that can lead to issues with air tools. Moisture can accumulate in the tank during compression, and if not drained regularly, it can cause corrosion and rusting, ultimately damaging the tank. Additionally, the presence of moisture can affect the performance and functionality of air tools, leading to potential problems. Therefore, draining the water from the tank is essential to maintain its longevity and ensure optimal performance of the air tools.Rate this question:
-
- 20.
What is another term for a Quick Coupler?
-
Quick Plug
-
Plug Coupler
-
Quick Disconnect
-
Coupler Plug
Correct Answer
A. Quick DisconnectExplanation
A Quick Coupler is commonly referred to as a Quick Disconnect.Rate this question:
-
Quiz Review Timeline (Updated): Aug 23, 2024 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Aug 23, 2024Quiz Edited by
ProProfs Editorial Team -
Jun 05, 2012Quiz Created by
Forney1932
Back to top