Forklift Refresher Training Quiz

30 Questions | Total Attempts: 355

SettingsSettingsSettings
Please wait...
Refresher Training  Quizzes & Trivia

Questions and Answers
  • 1. 
    Forklift use should start with an inspection including:
    • A. 

      A. Tires

    • B. 

      B. Hoses

    • C. 

      C. Lights

    • D. 

      D. All of the above

  • 2. 
    Operators of pallet jack forklifts are not required to be certified.
    • A. 

      True

    • B. 

      False

  • 3. 
    If a forklift has a seat belt but will only be operated on smooth concrete it is not required to be usd.
    • A. 

      True

    • B. 

      False

  • 4. 
    The overhead guard and load backrest have been removed from your truck and re being repaired.  It is safe to use the truck as long as you are careful.
    • A. 

      True

    • B. 

      False

  • 5. 
    A certified forklift operator is only aproved to operate the type of forklift they were trained on and have successfully completed a skills evaluation.
    • A. 

      True

    • B. 

      False

  • 6. 
    There are two 4 foot high loads stacked one on one block that block your forward view.  Which approach below is the safest approach?
    • A. 

      A. Lift the load until you can see

    • B. 

      B. Go forward anyway

    • C. 

      C. Travel in reverse (except on ramps)

    • D. 

      D. Make two trips so that you can see over both loads and drive with loads in a down position

  • 7. 
    It is okay to turn on a ramp as long as you go slowly.
    • A. 

      True

    • B. 

      False

  • 8. 
    Spread the forks as wide as possible before lifting a load.
    • A. 

      True

    • B. 

      False

  • 9. 
    A truck without a load will never tip over, even on a ramp
    • A. 

      True

    • B. 

      False

  • 10. 
    You should cross railroad tracks slowly and at 45-degree angles.
    • A. 

      True

    • B. 

      False

  • 11. 
    Tractor-trailers' wheels always need to be chocked prior to loading/unloading.
    • A. 

      True

    • B. 

      False

  • 12. 
    If your counterbalance truck begins to tip over, don't jump.  Why?
    • A. 

      A. You could get trapped under the truck or overhead guard.

    • B. 

      B. The truck cannot tip over anyway.

  • 13. 
    I don't need to follow lock-out procedures when working on a forklift since there is no hazard as long as it is not running.
    • A. 

      True

    • B. 

      False

  • 14. 
    When leaving your truck, you should put the directional control in neutral, fully lower the forks, and:
    • A. 

      A. Tilt the mast fully back

    • B. 

      B. Hide the key

    • C. 

      C. Set the parking brake, and remove the key

  • 15. 
    Is it okay to operate trucks with your head and arms outside the operator's compartment?
    • A. 

      A. No, never place any part of your body outside the comprtment

    • B. 

      B. Yes, as long as the truck is not in an aisle

    • C. 

      C. Yes, but only if you are moving a load

  • 16. 
    The controls of all fork trucks are the same.
    • A. 

      True

    • B. 

      False

  • 17. 
    Lift trucks are not required to have a lifting capacity plate if they have a lifting capacity below 5,000 pounds.
    • A. 

      True

    • B. 

      False

  • 18. 
    The stability triangle refers to the end of the forks and the top of the mast.
    • A. 

      True

    • B. 

      False

  • 19. 
    Determining a safe lifting capacity typically requires knowing what details about the lift?
    • A. 

      A. Load weight

    • B. 

      B. Load shape

    • C. 

      C. Forklift weight

    • D. 

      D. All of the above

  • 20. 
    You can safely increase a forklift's lifting capacity if you increase the amount of counter weight on the forklift.
    • A. 

      True

    • B. 

      False

  • 21. 
    The distance between wheels is the only factor in determing the stability pryamid.
    • A. 

      True

    • B. 

      False

  • 22. 
    The inch pounds equation is (A + B) X C = Inch Pounds.  What does B represent?
    • A. 

      A. Distance from the front of the forks to the load center

    • B. 

      B. Distance from the center of the front wheels to the front face of the fork

    • C. 

      C. Capacity of the forklift

    • D. 

      D None of the above

  • 23. 
    Pre-check inspections should be completed at the start of the work shift.  This inspection should be documented and the records retained.
    • A. 

      True

    • B. 

      False

  • 24. 
    As long as they are provided by the manufacturer, attachments have no effect on the capacity of a forklift.
    • A. 

      True

    • B. 

      False

  • 25. 
    Fluid levels only need to be checked once per week.
    • A. 

      True

    • B. 

      False

Back to Top Back to top