3P051 PRE-TEST Quiz

1. What is the most important thing the student should understand at the end of a feedback session?

What they did well

What they did poorly

How they can improve

How they can suceed

2. The most common and accurate position for firing the M240 when fired over level or uniformly sloping terrain?

Prone position

Assault position

Under arm position

Vehicle-mounted position

3. What type of hearing protection should a Combat Arms instructor wear during live fire training?

Earmuffs only

Earplugs only

Both

Either

4. Why is soft wood used as a facing for baffles?

Stop ammunition

Control ricochets

Protect ammunition

Support target stands

5. What is the maximum effective range for an area target with M4 carbine?

800 meters

700 meters

600 meters

500 meters

6. What type of tool is used to tighten the gas carrier key screws on an M16 bolt carrier is the?

Socket Wrench

Torque Wrench

Hex or Allen Wrench

Adjustable combination wrench

7. When lubrication an M16A2, place on drop oil

On the buffer guide retaining detent

Down the bolt carrier

On the front sight detent

Down the gas tube

8. The two purposes of a range card is to?

Record firing data and document defensive fire planning

Document defensive fire planning and provide for limited visibility firing

Prevent engaging friendly troops and provide for limited visibility firing

Allow multiple gun crews to use the same weapon and to record firing data

9. Pits are allowable in the bore of an M16A2 barrel if they are

As wide as a land or groove, and 3/8 inch or less in length

Wider than a land or groove, and 3/8 inch or less in length

As wide as a land or groove, and 1/2 inch or less in length

Wider than a land or groove, and 1/2 inch or less in length

10. How far does the laser Aiming Lighting project a visible infrared dot from the weapon

150 meters

150 ft

100 meters

100 feet

11. Which common error involves moving your head, closing your eyes, tensing the arms, or any combination of these

Jerking

Bucking

Healing

Flinching

12. Which publication includes the risk category for a munitions item?

Air Force Handbook (AFH) 31-223

Air Force Instruction (AFI) 31-209

Air Force Manual (AFM) 36-2226

AFI 31-101

13. The primary purpose of range flags and streamers is to

Identify range wind conditions

Identify type of weapon in use

Identify range location

Improve safety

14. What is the average battery life for the M68 sight?

50 to 75 hrs

50 to 100 hrs

75 to 500 hrs

75 to 600 hrs

15. The important characteristic of the M240B machine gun that permits rapid barrel changes is the

Unique gas system

Barrel's fixed headspace

Receiver's barrel release lever

Weapon's firing from the open bolt

16. When you fire an M16A2 rifle at long distances, how many times does the bullet intersect your line of sight

Three times

Two time

One time

None

17. Which piece of training equipment can be used in a fully lighted room?

Slide projector

Opaque projector

Overhead projector

16mm film projector

18. In which allowance standard are items for CA training?

AS 006

AS 538, Part C

AS 538, Part H

AS 601

19. An associated with the M203 sight manipulation, is placing the sight?

On the weapon

In the proper position

On the correct setting for zero and target engagement

In the proper position and with the proper range setting

20. The M203 grenade launcher is cocked by?

Trigger mechanism

Safety mechanism

Barrel assembly

Barrel latch

21. When fire is delievered into rising terrain, the beaten zone becomes?

Shorter

Longer

Wider

Elliptical

22. What risk category includes the M9 handgun and M870 shotgun?

I

II

III

IV

23. The recommended height of the tower floor above the firing platform is at least

2 feet

4 feet

5 feet

6 feet

24. The minimum allowable trigger pull for the M203 grenade launchers is

3 lbs

5 lbs

7 lbs

8 lbs

25. What results from measurement and judgement weighted againist predetermined standards?

Student participation

Effective evaluation

Effective learning

Student Feedback

26. What AF Form must be displayed in a prominent location in a munitions storage area?

1047

1473

2047

2074

27. Beyond what distance does the M203 grenade launcher need to be repositioned form the shoulder when firing ?

100 meters

150 meters

200 meters

225 meters

28. How should an outdoor earthen backstop be inspected for lead buildup?

Push a 3 foot rod into the dirt

Check the erosion behind target point

Use a 4-pound hammer to tap a 3/8-inch rod 3 feet into the dirt

Use a 4-pound hammer to tap a 3/4-inch rod 3 feet into the dirt

29. What two things does effective feedback focus on?

Quantity and quality

Results and quality

Audience and performance

Student and performance

30. What is the highest level of maintence performed in the CA shop?

Field maintenance

Depot maintenance

Operator Maintenance

Individual support maintenance

31. What is the minimum acceptable number of times a trigger pull test must be performed on an M16A2?

1

3

5

Until the hammer trips

32. Which part of the M9 pistol is made of aluminum?

Slide

Barrel

Receiver

Magazine

33. What are the two most critical elements in aiming a handgun

Sight alignment and sight picture

Breath control and trigger squeeze

Sight picture and a steady firing position

A steady firing position and breath control

34. What is the ideal target distance for zeroing an M240B

10 meters

300 meters

500 meters

700 meters

35. When visualizing a training aid you are?

Developing, designing, and building the aid

Using your imagination and knowledge to design an aid

Assisting your base graphics section in the building the aid

Using a very bright and colorful aid to support a lesson

36. What is the next step in M16A2 rifle sight adjustment afer firing a good three-shot group at a zero target

Reevaluate the size or the shot group

Determine the distance from the point of aim to the center of the target

Determine the distance from the center of the grouping to the aiming point

Triangulate the shot group and determine which shooting fundamental needs to be emphasized

37. What is the minimum width of the top of an earth beam?

5 meter

4 meter

3 meter

2 meter

38. When may the AN/PVS 7-series of night vision goggles be used during daylight hours

Never

On a very cloudy, overcast day

When the image intensifier is turned all the way down or off

When the daylight cap is placed on the objective lens of the goggles

39. If the first line on a bore erosion gauge passes into the chamber of an M249 barrel this indicates the barrel

Can continue in service

Has excessive bore erosion and must be replaced

Can continue in service, but cannot be deployed overseas

Has limited bore erosion and must be regauged every 2,000 rds

40. Evaluation By an end product checklist is most suited for

Disassembling an M16A2 rifle

Field stripping an M240B machine gun

Firing the M16A2 rifle qualification course

Preforming M240 machine gun clearing procedures

41. What is installed on the AN/PVS-4, night vision sight, to enable it to be used during normal light conditions

Lens cap

Daylight cover

Daylight shield

Objective lens cover

42. Plunging fire is not obtained when firing

From high ground to low ground

From low ground to high ground

Over level terrain

Over uneven terrain

43. What is the first step in remedial action for the M4 carbine?

Remove the magazine

Lock the bolt to the rear

Place the weapon on safe

Check for a double feed in the chamber

44. What does sensing determine when shooting a grenade launcher?

Distance to the target

Identifies targets at known distance

Which direction the wind is blowing

Where the grenade explodes with respect to the target

45. In properly aligned m870 the front sight

Bead is in line with the lower portion of the rear sight groove and the target

Blade is in line with th rear sight notch and centered on the target

Is in line with the rear sight slide and centered on the target

Blade is in line with the upper portion of the rear sight

46. What tool is used for making initial adjustments on the AN/PAQ-4 infrared aiming light?

Allen wrench

Adjustment tool

Crosspoint screwdriver

None figure pressure is sufficient

47. The maximum tolerance for firing pin protrusion with the 203 grenade launchers is

.032 in

.041 in

.045 in

.047 in

48. When an instructor allows unfavorable experiences to enter into the evaluation process he is exhibiting what pitfall?

Halo effect

Apathy

Effect of halo

Lack of judgement

49. Where can you find information on M240B bipod-mounted crew drills?

AF 36-2226

AFMAN 36-2227

FM 23-9

FM 23-67

50. When performing the triangulation exercise, what is being triangulated?

Three pencil dots

Three bullet holes in a target

The size of the shot groups on three targets

The shooter's eye, the weapon's sights, and the target

3P051 Pre-test Quiz