2A656 CDC 1

1. A symbol entered on a maintenance form reflects the opinion of the?

Shop supervisor

Maintenance officer

Squadron commander

Individual making the entry

2. Which is the correct method for writing 30 January 2011?

20110130

01/30/11

30/01/11

11/01/30

3. Which type of nuclear radiation is the most deadly?

Alpha

Beta

Delta

Gamma

4. Air Force property responsibility is imposed by law on?

Commanders only

All millitary employees

Comanders and supervisors only

All millitary and civillian employees

5. Which kind of technical order (TO) contains operational checkout procedures?

Job Guide

Fault Isolation

General Vehicle

Schematic Diagram

6. What should be the main concern when planning the layout of any shop area?

Saftey

Lighting

Adequate work space

Location of test equipment

7. When a new Air Force Technical Order (AFTO) Form 781A is initiated, what kind of discrepancies cannot be transferred to the AFTO Form 781K?

Red X

Red dash

Red diagonal

Discrepancies with a supply document number

8. The Air Force Technical Order (AFTO) Form 244 is used to document discrepancies and corrective actions for?

Aircraft

Batteries

Equipment

Multimeters

9. What type of tasks may you perform in the immediate area of explosives?

Mission critical

Routine

None

Core

10. What must you ensure when you are transporting squibs?

Not to exceed the maximum amount of squibs

Other personnel are not in the immediate area

The squibs are in a protective container

The use of a specially designed vehicle

11. While troubleshooting, you are using a wiring diagram to help you locate a malfunctioning compnent. after determining which component is faulty, you want to determine its part number . To do this, you would check the wiring diagram's?

Numerical index

Reference designator

Line replaceable unit index

Line replaceable unit designation

12. Which situation illustrates a physical hazard presented by a chemical hazard?

Acute liver damage

Irritation of the kidney

Second degree skin burn

Chronic exposure to vapors

13. What is considered to be a safe distance in front of jet intake ducts?

10 feet

15 feet

20 feet

25 feet

14. The Integrated Maintenance Data System (IMDS) Training Management Subsystem can be used to monitor?

Upgrade training

Optional training

Seasonal training

Qualitative training

15. Which is a thorough and searchng inspection?

Minor

Major

Postflight

Home station check

16. When you are servicing an aircraft with liquid oxygen (LOX), do not wear?

Cuffless trousers

A battle dress uniform (BDU) cap

Leather welders gauntlet cuff gloves

Shoes which fit loosley around the top

17. What is a temporary storage location designed to stor nuclear materials in transit through a base called?

Pyramid Alert

Safegaurding

Safe Haven

Tempest

18. Which publications are considered working handbooks?

Air Force Manuals

Air Force pamphlets

Air Force instructions

Recurring publications

19. There are how many levels of maintenance?

Two

Three

Four

Five

20. Quality maintenance is the responsibility of maintenance technicians, supervisors, and commanders who work in concern with?

Maintenance training

Quality assurance

Resources

Egress

21. Bench stock supplies should be replenished when the authorized quantity on-hand drops below what amount?

40%

50%

60%

70%

22. In the basic technical order (TO) numbering system, what is the minimum groups of numbers each TO will have?

Two

Three

Four

Five

23. The Maintenance Integrated Data Access System (MIDAS) page number is?

A two-digit numbering system expressed as one element of two digits

A six-digit numbering system expressed as the elements of two digits each

A four-digit numbering system expressed as two elents of two digits each

An eight-digit numbering system expressed as four elements of two digits each

24. Which is not one of the elements of the maintenance training program?

Upgrade training

Managment training

Qualification training

Cross- Utilization training

25. An airman who signs out a toolbox assumes which type of property responsibility for that toolbox?

Supervisory

Custodial

Individual

Command

26. Reducing the time an aircraft is out of commision is an objective of which inspection?

Phase

Hourly

Periodic

Isochronal

27. Which mishap prevention tag is used to warn personnel against potential hazards?

Danger

Caution

Out of Order

Do Not Start

28. Who is responsible for managing the wing's quality assurance progams?

Flight Chief

Quality assurance section chief`

Maintenance group commander

Aircraft maintenance sqaudron commmander

29. Which flight is part of a maintenance squadron?

Test, measurement, and diagnostic equipment

Maintenance operations and progams

Quality assurance

Resources

30. What technical order (TO) explains the Material Deficiancy Reporting System?

00-5-15

00-25-195

00-35D-54

00-25C-234

31. The second posotion of the Expendability/ Recoverability/ Repairablility/ Category (ERRC) Designation Code indicates?

Expendability

Repair level

Supplier

Cost

32. If you work on an aircraft on the flightline, you are doing which level of maintenance?

Depot

Intermediate

Organizational

Off-equipment

33. The list of applicable publications (LOAP) lists Technical Orders that apply to?

Active aircraft time compliance technical orders

A specific aircraft

Overhaul depots

A specific tester

34. Which Air Force publication is a source of information for the prevention of accidents?

Air Force Instruction (AFI) 91-202

Air Force Instruction (AFI) 8-2

AFI 91-204

AFR 39-1

35. The five authorized inspection concepts used by the Air Force are?

Major, minor, isochronal, postflight

Major, minor, shop, home station, postflight

Periodic, home station, postflight, isochronal, programmed depot maintenance

Periodic, phase, isochronal, programmed depot maintenance, airline/manufacturer maintenance

36. Which inspection is used to detect defects that could have developed durning ground operation of an aircraft?

Preflight

Thruflight

Postflight

End-of-runway

37. The first part of the national stock number indicates the?

Part code

Bureau code

Item identification

Supply classification

38. How much electrical current does it take to cuse muscle paralysis?

.001 amps

.005 amps

.010 amps

.015 amps

39. Which Air Force (AF) Form is used to report ground safety accidents invloving personeel (not including aircraft) ?

AF Form 711

AF Form 711B

AF Form 117

AF Form 117B

40. Saftey supplements to technical orders are identified with a border of?

Black SS's on the title page

Red SS's on the title page

Black SS's on all pages

Red SS's on all pages

41. Which technical order (TO) explains how to maintain and inspect a particular weapons system?

Operations and Maintenance

Method and Procedures

Time Compliance

Abbreviated

42. Revisions are issued when changes exceed what percentage of the basic TO?

50

60

70

80

43. High Frequency radiation is not produced by?

Radio equipment

Radar equipment

Nuclear weapons

Electronic counter-meausres equipment

44. A Category II, Product Quality Deficiency Report that has been submitted for a defect in workmanship must be forwarded to the screening point within?

1 workday

2 workdays

3 workdays

4 workdays

45. Which element must be included in a workspace written hazard communication program?

Hazardous material inventory

Hazardous waste disposal procedures

Telephone number of hazardous material monitor

List of routine operations performed in the work center

46. What types of property responsibility can be changed to Department of Defense (DOD) pesonnel?

Command and custodial

Individual and custodial

Command and supervisory

Supervisory and custodial

47. What is the minimum information required on a hazardous chemical inventory?

Name, location, and detailed ingrediant list of the material

Name, location, and quantity of material authorized

Name and location of the material

Name of the material

48. Liquid nitrogen must be stored below what minimum temperature to remain in a liquid state?

-310.8F

-315.8F

-320.8F

-325.8F

49. For personnel electrostatic discharge (ESD) grounding, you must use a skin contact wrist strap connected to the workbench surface. This strap must have a resistance of at least?

1 ohm

10 ohms

1 megaohm

10 megaohms

50. Which saftey standard of the nuclear surety program includes a pre task breifing?

Weapons security

Individual Responsibilities

Prevent nuclear explosions

Prevent unauthorized or accidental actions

51. The primary responsibility for formal upgrade training rests with?

Training managment personnel

The commander

The supervisor

The individual

52. A series of red X's printed around the border of the first page of time compliance technical order (TCTO) signifies?

An inspection action TCTO

An immediate action TCTO

An routine action TCTO

An urgent action TCTO

53. The first number group within a technical order (TO) number identifies the?

Specific equipment

Section of the TO

TO category

Kind of TO

54. Which deficiency report is used for technical order (TO) deficiancy that invovles saftey or the unit mission?

Interim

Urgent