True And False Questions On Woodwork Safety!

Reviewed by Editorial Team
The ProProfs editorial team is comprised of experienced subject matter experts. They've collectively created over 10,000 quizzes and lessons, serving over 100 million users. Our team includes in-house content moderators and subject matter experts, as well as a global network of rigorously trained contributors. All adhere to our comprehensive editorial guidelines, ensuring the delivery of high-quality content.
Learn about Our Editorial Process
| By Kenbessac
K
Kenbessac
Community Contributor
Quizzes Created: 7 | Total Attempts: 5,945
| Attempts: 984 | Questions: 46
Please wait...
Question 1 / 46
0 %
0/100
Score 0/100
1.  Loose jewelry should be _____________ before operation of the drill press.

Explanation

Before operating the drill press, loose jewelry should be removed. This is important to ensure safety during the operation. Loose jewelry can get caught in the moving parts of the drill press, causing injury to the operator. Therefore, it is necessary to remove any jewelry that could potentially pose a hazard before using the drill press.

Submit
Please wait...
About This Quiz
True And False Questions On Woodwork Safety! - Quiz

Here are some true and false questions on woodwork safety! If you are into the woodwork, you must have a clear knowledge of the tools that are used at the workshop, how they are used, and how to ensure you minimize the chances of accidents occurring. Below are some true... see moreand false questions on woods safety. Take them up and get to refresh your memory on some safety measures. All the best!
see less

Personalize your quiz and earn a certificate with your name on it!
2. Before using the Miter Saw you should clean the work area of small waste parts.

Explanation

Before using a Miter Saw, it is important to clean the work area of small waste parts. This is because small waste parts can obstruct the cutting process and potentially cause accidents or damage to the tool. By cleaning the work area, you ensure a clear and safe space to operate the Miter Saw effectively.

Submit
3. Talking to somone while using the Miter saw may result in serious accidents

Explanation

Using a miter saw requires full attention and focus to ensure safety. If someone is talking to you while you are using the miter saw, it can distract you and divert your attention away from the task at hand. This distraction increases the risk of accidents and serious injuries. Therefore, it is important to avoid talking to someone while operating a miter saw to prevent any potential harm.

Submit
4. Loose hair and clothing must always be tucked in while useing the drill press

Explanation

Loose hair and clothing can pose a safety hazard while using a drill press. Loose hair can get caught in the drill bit or other moving parts, leading to injury. Similarly, loose clothing can get entangled in the machine, causing accidents. Therefore, it is important to always tuck in loose hair and clothing while using a drill press to ensure personal safety.

Submit
5. You do not need any safety glasses when using any of the sanders.

Explanation

Safety glasses are necessary when using sanders to protect the eyes from flying debris, dust, and other potential hazards. Therefore, the statement that you do not need any safety glasses when using any of the sanders is incorrect.

Submit
6. Do not use sanding paper that is loose or torn.

Explanation

Using loose or torn sanding paper can be dangerous and ineffective. Loose sanding paper can easily detach from the sanding tool and cause injury to the user or damage to the workpiece. Torn sanding paper may not provide a smooth and even sanding surface, leading to uneven results. Therefore, it is important to use sanding paper that is in good condition to ensure safe and effective sanding.

Submit
7. You should never carry the nailer or stapler with you finger on the trigger.

Explanation

Carrying a nailer or stapler with your finger on the trigger can be dangerous as it increases the risk of accidental discharge. This can result in injury to yourself or others around you. Therefore, it is important to always keep your finger off the trigger when carrying these tools to ensure safety.

Submit
8. The air nailer should never be operated above 90 PSI.

Explanation

Operating an air nailer above 90 PSI can be dangerous as it can lead to excessive force and cause the nails to penetrate too deeply or even go through the material being nailed. This can result in damage to the workpiece or potential injury to the user. Therefore, it is important to follow the manufacturer's recommended PSI range for safe and effective operation of an air nailer.

Submit
9. When using the miter saw it required that you the saw with the safety guard attached.

Explanation

When using a miter saw, it is important to have the safety guard attached. The safety guard is designed to protect the user from any potential flying debris or accidental contact with the saw blade. It acts as a barrier between the user and the blade, reducing the risk of injury. By having the safety guard attached, it ensures that the user is taking necessary precautions and following proper safety protocols while operating the miter saw.

Submit
10. It is safe to use your fingers to remove the sawdust from the saw cutting line while the blade is turning.

Explanation

It is not safe to use your fingers to remove sawdust from the saw cutting line while the blade is turning. This is because the blade is sharp and can cause serious injury if it comes into contact with your fingers. It is recommended to wait for the blade to stop spinning and then use a brush or another tool to remove the sawdust safely.

Submit
11. While cutting material on the Miter Saw, it never ok to cross your arms.

Explanation

Crossing your arms while cutting material on a Miter Saw is unsafe and should never be done. This can lead to a loss of control and increase the risk of accidents or injuries. Keeping your arms in the correct position ensures better control and stability while operating the saw, reducing the chances of accidents. Therefore, it is important to always avoid crossing your arms while using a Miter Saw.

Submit
12. It is safe to carry the air nailer by the hose.

Explanation

It is not safe to carry the air nailer by the hose because the hose is not designed to support the weight of the nailer. Carrying the nailer by the hose can put strain on the hose, causing it to weaken or detach from the nailer. This can result in the nailer falling and potentially causing injury or damage. It is recommended to carry the nailer by its handle or use a separate carrying case for transportation.

Submit
13. When placing the drill in storage the cord should be neatly wrapped around the handle

Explanation

When placing the drill in storage, it is recommended to neatly wrap the cord around the handle. This is important to prevent the cord from tangling or getting damaged, ensuring that it remains in good condition for future use. Additionally, neatly wrapping the cord makes it easier to store the drill without any loose or dangling wires, reducing the risk of accidents or entanglements.

Submit
14. You should use excessive pressure on the top of the sander for fast cutting.

Explanation

Excessive pressure on the top of the sander is not recommended for fast cutting. Applying too much pressure can cause the sander to become less effective and potentially damage the surface being worked on. It is important to use the appropriate amount of pressure to achieve desired results without compromising the quality of the work or the tool itself.

Submit
15. It is safe to change the blade with the cord connected to the power source.

Explanation

Changing a blade with the cord connected to the power source is not safe. This is because there is a risk of electric shock if the cord is accidentally touched or if there is a fault in the power source. It is important to always disconnect the power source before performing any maintenance or changing blades to ensure personal safety.

Submit
16. It is unsafe to start the Miter saw while the blade is in contact with the material to be cut.

Explanation

Starting a miter saw while the blade is in contact with the material to be cut is unsafe because it can lead to accidents and injuries. When the blade is in contact with the material, it can cause the saw to kickback or bind, resulting in the material being thrown or the saw being pulled out of control. This can pose a serious risk to the operator and anyone nearby. Therefore, it is important to always ensure that the blade is clear of the material before starting the miter saw.

Submit
17. It is ok to use nailes or staples that are not manufactured for use with the tool.

Explanation

Using nails or staples that are not manufactured for use with a tool can be dangerous and potentially lead to accidents or damage to the tool. Tools are designed to work with specific types and sizes of nails or staples, and using ones that are not intended for use with the tool can cause them to jam, break, or malfunction. It is important to always use the correct and recommended fasteners for any tool to ensure safe and proper operation.

Submit
18. It is safe to load the nailer or stapler with the air supply connected.

Explanation

Loading the nailer or stapler with the air supply connected is not safe. This is because it can lead to accidental firing of the tool, causing potential harm or injury. It is always recommended to disconnect the air supply before loading or unloading the tool to ensure safety.

Submit
19. It is safe to point the nail gun or stappler at someone with or with out the air supply disconnected.

Explanation

It is not safe to point the nail gun or stapler at someone, whether the air supply is connected or disconnected. The act of pointing any tool that is designed to shoot projectiles at someone can cause serious injury or harm. Therefore, the correct answer is false.

Submit
20. It is unsafe to fire the air nailer before knowing what exact path the nail will take.

Explanation

Firing an air nailer without knowing the exact path the nail will take is unsafe because it can lead to accidents or damage. The nail may hit unintended objects or surfaces, causing injury to oneself or others nearby. It is important to have a clear understanding of the path the nail will follow to ensure safe and accurate operation of the air nailer.

Submit
21. Before using the nail gun it should be lubricated with 1 drop of air tool oil.

Explanation

The statement is true because lubricating the nail gun with air tool oil before using it helps to reduce friction and prevent wear and tear on the internal components. This ensures smooth operation and prolongs the lifespan of the tool.

Submit
22. During the drilling operation you should never remove the chips from the stock while drilling.

Explanation

During the drilling operation, it is important not to remove the chips from the stock while drilling. This is because the chips act as a coolant and lubricant, helping to prevent overheating and damage to the drill bit and the stock material. Removing the chips prematurely can lead to increased friction, heat buildup, and potentially cause the drill bit to break or the stock material to warp. Therefore, it is advisable to allow the chips to be expelled naturally during the drilling process.

Submit
23. When making a cut with the Miter saw it should be lowered  into the work piece as fast as possible.

Explanation

When making a cut with the Miter saw, it should not be lowered into the workpiece as fast as possible. It is important to lower the saw blade slowly and steadily to ensure accuracy and safety. Lowering the saw too quickly can result in a rough cut, damage to the workpiece, and potential injury to the user. Therefore, the correct answer is False.

Submit
24. It is unsafe to fire the nail or staple gun before making contact with work.

Explanation

Firing a nail or staple gun before making contact with the work is unsafe because it can lead to accidental injuries. By making contact with the work surface first, it ensures that the nail or staple is properly aligned and positioned before firing, reducing the risk of the fastener going off course or causing damage. This safety precaution helps to prevent potential accidents and promotes safe usage of the tool.

Submit
25. It is unsafe to use the Miter Saw while the safety guard is stuck in the up position

Explanation

When the safety guard of a miter saw is stuck in the up position, it exposes the blade, increasing the risk of accidents and injuries. The safety guard is designed to cover the blade when it is not in use or during certain cutting operations to prevent contact with the blade. Therefore, it is unsafe to use the miter saw without the safety guard in the proper position.

Submit
26. Your fingers should never be closer than 3 inches from blade while cutting lumber on the miter saw.

Explanation

It is important to maintain a safe distance from the blade while operating a miter saw to avoid any potential accidents or injuries. Keeping your fingers at least 3 inches away from the blade ensures that they are not at risk of coming into contact with the sharp rotating blade, reducing the chances of getting cut or injured. Therefore, the statement is true.

Submit
27. Leaving the nail gun unattended with the air supply attached is unsafe

Explanation

Leaving the nail gun unattended with the air supply attached is unsafe because it can pose a risk of accidental discharge. If the nail gun is left unattended and someone accidentally triggers it, it can cause serious injury or damage. Additionally, if the air supply is left attached, there is a possibility of the nail gun being activated by someone else or by any unintentional movement, leading to potential accidents. Therefore, it is important to always disconnect the air supply and properly store the nail gun when it is not in use to ensure safety.

Submit
28. If the drill grabs or gets stuck causing the stock to spin, you should imediatly grab the stock before it becomes damaged.

Explanation

If the drill grabs or gets stuck causing the stock to spin, it is not recommended to immediately grab the stock. Doing so can be dangerous and may result in injury. Instead, it is advised to turn off the drill and wait for the stock to come to a complete stop before attempting to remove it. This ensures safety and prevents any potential damage to the stock or harm to the person handling it.

Submit
29. Small work pieces should be held in a jig or clamped to the table when using the sander.

Explanation

When using a sander, it is important to hold small work pieces in a jig or clamp them to the table. This is because small pieces can easily slip or move during sanding, which can be dangerous and lead to accidents. By securing them in a jig or clamping them to the table, the work pieces remain stable and steady, allowing for safe and effective sanding. Therefore, the statement "Small work pieces should be held in a jig or clamped to the table when using the sander" is true.

Submit
30.  If you are trying to drill cylindrical stock on the drill, you should use a _________ to hold the stock firmly.

Explanation

When drilling cylindrical stock on a drill, it is important to hold the stock firmly to prevent it from slipping or rotating during the drilling process. A vise is a tool specifically designed for this purpose, as it can securely grip and hold the stock in place. Using both hands or a round block would not provide the same level of stability and control as a vise, making it the correct choice for holding the stock firmly.

Submit
31. When using the Miter Saw you must change the angle of cut while the motor is running.

Explanation

It is not necessary to change the angle of cut while the motor is running when using a Miter Saw. The angle of cut can be adjusted before starting the motor, and once the desired angle is set, the motor can be turned on to make the cut. Changing the angle of cut while the motor is running can be dangerous and should be avoided. Therefore, the correct answer is False.

Submit
32. It is safe to remove material from the Miter Saw table before the blade has stopped.

Explanation

It is not safe to remove material from the Miter Saw table before the blade has stopped because the blade is still spinning and can cause serious injuries if it comes into contact with the material or the user's hands. It is important to wait for the blade to completely stop before removing any material to ensure safety.

Submit
33. It is safe to use the nailer or stapler with the safety contact plunger inoperable or removed.

Explanation

It is not safe to use the nailer or stapler with the safety contact plunger inoperable or removed. The safety contact plunger is an important safety feature that prevents accidental firing of the nailer or stapler. Without it, there is a risk of unintentional discharge of nails or staples, which can cause injury to the user or others nearby. Therefore, it is important to ensure that the safety contact plunger is functioning properly before using the nailer or stapler.

Submit
34. Small pieces can be drilled without clamping them to the table or holding in a vise

Explanation

Small pieces cannot be drilled without clamping them to the table or holding them in a vise. When drilling, it is important to secure the workpiece to prevent it from moving or spinning during the drilling process. Failure to do so can result in accidents, damage to the workpiece, or poor drilling results. Therefore, the statement is false.

Submit
35. When drilling through a board you must always place a scrap piece of wood under the stock you are drilling

Explanation

When drilling through a board, it is important to place a scrap piece of wood under the stock being drilled to prevent tear-out or splintering on the backside of the board. The scrap wood acts as a support, providing a solid surface for the drill bit to push against, reducing the chances of the wood fibers splitting or breaking. This practice helps to ensure clean and precise holes without damaging the material being drilled.

Submit
36. When placing sanding paper on the sander, you should never alighn the holes in the paper with holes on the sander

Explanation

When placing sanding paper on the sander, aligning the holes in the paper with the holes on the sander is actually the correct way to do it. This allows for better dust collection and prevents the paper from clogging up quickly. If the holes are not aligned, the dust may not be effectively collected, leading to poor sanding performance and potentially damaging the sander. Therefore, the correct answer is False.

Submit
37. When drilling you must apply excessive pressure to the drill while cutting or drilling holes.

Explanation

When drilling, it is not necessary to apply excessive pressure to the drill while cutting or drilling holes. In fact, applying excessive pressure can lead to several problems such as overheating, reduced accuracy, and increased wear on the drill bit. Instead, it is recommended to let the drill bit do the work and apply steady, moderate pressure to maintain control and prevent damage to the drill or workpiece.

Submit
38. 15.       You can use the  sander to remove large amounts from a board. (more than 1/16th inch)

Explanation

The statement is false because a sander is not typically used to remove large amounts from a board. A sander is more commonly used for smoothing and finishing surfaces, rather than for heavy material removal. For removing large amounts from a board, other tools like a saw or a planer would be more appropriate.

Submit
39. Do not sand wood that has exposed glue or varnish on it.

Explanation

It is recommended not to sand wood that has exposed glue or varnish on it because sanding can remove or damage the glue or varnish layer, affecting the overall integrity and appearance of the wood.

Submit
40. While sanding you should sand across the grain for the best sanding results

Explanation

Sanding across the grain is not the best technique for achieving the best sanding results. Sanding with the grain is generally recommended as it helps to smooth the surface evenly and prevents the risk of creating scratches or marks on the material. Sanding across the grain can cause the sandpaper to catch on the fibers, leading to uneven sanding and potentially damaging the surface. Therefore, the correct answer is false.

Submit
41. When placing the blade on the Miter Saw the teeth should point towards you.

Explanation

When placing the blade on the Miter Saw, the teeth should not point towards you. This is because the teeth of the blade should always face away from the user to ensure safety during operation. Placing the blade with the teeth pointing towards you can result in accidents or injuries. Therefore, the correct answer is False.

Submit
42. You should hold the sander to the stock before starting the motor.

Explanation

Holding the sander to the stock before starting the motor is not recommended. It is important to ensure that the motor is turned off before bringing the sander in contact with the stock to avoid any accidental damage or injury. Therefore, the correct answer is False.

Submit
43. The long end of the stock should go on the ______________ of the column of the drill press.

Explanation

The long end of the stock should go on the left side of the column of the drill press.

Submit
44.    Maintain a _____________ margin of safety form the drill bit.

Explanation

The correct answer is 2 because maintaining a smaller margin of safety from the drill bit is important for ensuring accuracy and precision in drilling operations. A smaller margin allows for better control and reduces the risk of errors or accidents. It also allows for more efficient drilling as it minimizes the distance between the drill bit and the desired target. Therefore, a smaller margin of safety is preferred in order to achieve optimal drilling results.

Submit
45. Material should never be placed against the Miter Saw fence while cutting material.

Explanation

Placing material against the Miter Saw fence while cutting material is safe and commonly done to ensure accuracy and stability during the cutting process. The fence provides support and helps in maintaining the desired angle and position of the material being cut. It is important to securely hold the material against the fence to prevent any movement or slippage while cutting.

Submit
46. It is unsafe to clear a jammed nail gun with out the air supply connected.

Explanation

It is safe to clear a jammed nail gun without the air supply connected. When the air supply is disconnected, there is no pressure to drive the nails, reducing the risk of accidental firing. However, it is still important to follow proper safety procedures and use caution when clearing a jammed nail gun to avoid any potential injuries.

Submit
View My Results

Quiz Review Timeline (Updated): Nov 16, 2023 +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Nov 16, 2023
    Quiz Edited by
    ProProfs Editorial Team
  • Oct 12, 2010
    Quiz Created by
    Kenbessac
Cancel
  • All
    All (46)
  • Unanswered
    Unanswered ()
  • Answered
    Answered ()
 Loose jewelry should be _____________ before operation of the...
Before using the Miter Saw you should clean the work area of small...
Talking to somone while using the Miter saw may result in serious...
Loose hair and clothing must always be tucked in while useing the...
You do not need any safety glasses when using any of the sanders.
Do not use sanding paper that is loose or torn.
You should never carry the nailer or stapler with you finger on the...
The air nailer should never be operated above 90 PSI.
When using the miter saw it required that you the saw with the...
It is safe to use your fingers to remove the sawdust from the saw...
While cutting material on the Miter Saw, it never ok to cross your...
It is safe to carry the air nailer by the hose.
When placing the drill in storage the cord should be neatly wrapped...
You should use excessive pressure on the top of the sander for fast...
It is safe to change the blade with the cord connected to the power...
It is unsafe to start the Miter saw while the blade is in contact with...
It is ok to use nailes or staples that are not manufactured for use...
It is safe to load the nailer or stapler with the air supply...
It is safe to point the nail gun or stappler at someone with or with...
It is unsafe to fire the air nailer before knowing what exact path the...
Before using the nail gun it should be lubricated with 1 drop of air...
During the drilling operation you should never remove the chips from...
When making a cut with the Miter saw it should be lowered  into...
It is unsafe to fire the nail or staple gun before making...
It is unsafe to use the Miter Saw while the safety guard is stuck in...
Your fingers should never be closer than 3 inches from blade while...
Leaving the nail gun unattended with the air supply attached is unsafe
If the drill grabs or gets stuck causing the stock to spin, you should...
Small work pieces should be held in a jig or clamped to the table when...
 If you are trying to drill cylindrical stock on the drill, you...
When using the Miter Saw you must change the angle of cut while the...
It is safe to remove material from the Miter Saw table before the...
It is safe to use the nailer or stapler with the safety contact...
Small pieces can be drilled without clamping them to the table or...
When drilling through a board you must always place a scrap piece of...
When placing sanding paper on the sander, you should never alighn the...
When drilling you must apply excessive pressure to the drill while...
15.       You can use the  sander...
Do not sand wood that has exposed glue or varnish on it.
While sanding you should sand across the grain for the best sanding...
When placing the blade on the Miter Saw the teeth should point towards...
You should hold the sander to the stock before starting the...
The long end of the stock should go on the ______________ of the...
   Maintain a _____________ margin of safety form the drill...
Material should never be placed against the Miter...
It is unsafe to clear a jammed nail gun with out the air supply...
Alert!

Advertisement