Frontier MS Quiz 1 Shop Safety
Settings
When operating in any such craft as woodwork or metalwork, safety should always be the first priority. After all, a job done well is a job done safely! How much do you know about the proper safety protocols involved?
- 1.Always wear eye_____________
- A.
Protection
- B.
Drops
- C.
Lenses
- D.
Glasses
- 2.Use equipment only with the instructor’s________________
- A.
Protection
- B.
Permission
- C.
Help
- D.
Safety Glasses
- 3.______________________all accidents or injuries
- A.
Fix
- B.
Ignore
- C.
Report
- D.
Defective
- 4.Do not use _____________equipment
- A.
Defective
- B.
Clean
- C.
New
- D.
Old
- 5.Never use equipment until you have been properly______________________
- A.
Funded
- B.
Instructed
- C.
Protected
- D.
Dressed
- 6.Loose clothing can cause___________________________.
- A.
Hearing loss
- B.
Protection
- C.
Buy new clothes
- D.
Injuries
- 7.Long hair must be_______________or covered with a cap
- A.
Tied back
- B.
Braided
- C.
Cut
- D.
Curled
- 8.No____________________ should be worn in the laboratory.
- A.
Jewelry
- B.
Shoes
- C.
Aprons
- D.
Hats
- 9.Wear ____________________shoes or boots
- A.
Closed
- B.
Open
- C.
Covered
- D.
Flip Flops
- 10.Approved protection earmuffs should be worn around _________________ equipment
- A.
Dirty
- B.
Noisy
- C.
Fast
- D.
Clean
- 11.A _____________________ must be worn when working where there is wood dust.
- A.
Coveralls
- B.
Dust mask
- C.
Face shield
- D.
Jeans
- 12.Finishing materials should only be used in ________________________ areas.
- A.
Well lit
- B.
Drafty
- C.
Secure
- D.
Well ventilated
- 13.Always _______________ spilled materials.
- A.
Ignore
- B.
Clean up
- C.
Walk By
- D.
Look at
- 14.Used rags are to be kept in a covered _____________________ container.
- A.
Wood
- B.
Metal
- C.
Plastic
- D.
Trash can
- 15.Never leave anything on the_________________ that could be slipped on or tripped over.
- A.
Floor
- B.
Workbench
- C.
Equipment
- D.
Ceiling
- 16.__________________________ vises when they are not in use
- A.
Close
- B.
Open
- C.
Down
- D.
Up
- 17.Workbenches should be kept ___________ and organized
- A.
Clear
- B.
Cluttered
- C.
Wiped down
- D.
Finished
- 18.Use ________________________ or a rag to clear away scraps and sawdust.
- A.
Your hat
- B.
Your shirt
- C.
Your hands
- D.
A brush
- 19.Tools should be used only for what they are _____________________________.
- A.
Designed to do
- B.
Up side down
- C.
Easiest to use
- D.
Until your done
- 20._________________________ tools should be carried with the edge or point held down toward the floor.
- A.
New
- B.
Dull
- C.
Sharp
- D.
Old
- 21.When you are finished with a tool, return it to its _______________________________.
- A.
Assigned storage area
- B.
Where you found it
- C.
On the table
- D.
On the floor
- 22.Ask for________________________ when you need to handle large or heavy material.
- A.
Permission
- B.
Help
- C.
Lunch
- D.
Money
- 23.Lift with your _________________ not with your back
- A.
Neck
- B.
Arms
- C.
Legs
- D.
Back
- 24.1. Never handle_____________________equipment if your hands are wet or if you are standing on a wet floor.
- A.
Writing
- B.
Hand
- C.
Electrical
- D.
Water
- 25.Equipment with a _______________power cord should be reported to the instructor. It should not be used
- A.
Good
- B.
Damaged
- C.
Clean
- D.
Blue
Back to top