Parts Of The Sewing Machine Quiz

Reviewed by Matt Balanda
Matt Balanda, BS (Aerospace Engineering) |
Science Teacher
Review Board Member
Matt Balanda, a Calvary Chapel Christian School leader with a Bachelor's in Aerospace Engineering and Mathematics, transitioned from Aerospace Engineering to Education with a Master's from California Baptist University. As the High School Vice-Principal and Physics teacher, he nurtures students' love of learning and faith, creating an enriching and transformational educational experience.
, BS (Aerospace Engineering)
Approved & Edited by ProProfs Editorial Team
The editorial team at ProProfs Quizzes consists of a select group of subject experts, trivia writers, and quiz masters who have authored over 10,000 quizzes taken by more than 100 million users. This team includes our in-house seasoned quiz moderators and subject matter experts. Our editorial experts, spread across the world, are rigorously trained using our comprehensive guidelines to ensure that you receive the highest quality quizzes.
Learn about Our Editorial Process
| By Katrina James
K
Katrina James
Community Contributor
Quizzes Created: 1 | Total Attempts: 22,495
Questions: 20 | Attempts: 22,500

SettingsSettingsSettings
Parts Of The Sewing Machine Quiz - Quiz


Check out this awesome 'Parts of the sewing machine quiz' given below. We've designed this quiz mainly to test your knowledge about a sewing machine and its parts. Do you use a sewing machine? If your answer is yes, you'll be able to pass this test quickly and easily. So, give it a try, and let's see how you perform. Are you ready to play it? Let's get started then. Hope you'll have fun!


Questions and Answers
  • 1. 

    Which part of the machine has to be in the "down" position before you can sew?

    • A.

      The take up lever

    • B.

      The Presser foot

    • C.

      The needle

    • D.

      The hand wheel

    Correct Answer
    B. The Presser foot
    Explanation
    The presser foot is the part of the machine that needs to be in the "down" position before sewing can occur. This is because the presser foot holds the fabric in place and ensures that it stays flat and steady while being sewn. When the presser foot is in the "down" position, it applies pressure to the fabric, preventing it from moving or shifting during the sewing process. This allows for more accurate and precise stitching.

    Rate this question:

  • 2. 

    What should you do if the take up lever is not visible?

    • A.

      Tell the teacher you broke the machine

    • B.

      It fell off and needs to be replaced

    • C.

      Turn the hand wheel and it will appear

    • D.

      Push the gas pedal and it will appear

    Correct Answer
    C. Turn the hand wheel and it will appear
    Explanation
    If the take up lever is not visible, turning the hand wheel can help it appear. This is because the take up lever is connected to the hand wheel mechanism, and turning the hand wheel can align the parts and bring the take up lever back into view.

    Rate this question:

  • 3. 

    This controls the movement of the needle and the take up lever.

    • A.

      Presser foot

    • B.

      Seam gauge

    • C.

      Handwheel

    • D.

      Bobbin case

    Correct Answer
    C. Handwheel
    Explanation
    The handwheel is responsible for controlling the movement of the needle and the take up lever in a sewing machine. By turning the handwheel, the needle is raised and lowered, and the take up lever moves the thread through the fabric. This allows for precise control over the stitching process and ensures smooth and accurate sewing.

    Rate this question:

  • 4. 

    This controls how fast the machine sews.

    • A.

      Gas pedal

    • B.

      Presser foot

    • C.

      Hand wheel

    • D.

      Backstitch

    Correct Answer
    A. Gas pedal
    Explanation
    The gas pedal is used to control the speed at which a machine sews. By pressing the pedal, the machine will sew faster, and by releasing pressure, the machine will sew slower. This allows the user to have control over the speed of the sewing process, making it easier to sew at a comfortable and manageable pace.

    Rate this question:

  • 5. 

    This allows the machine to stitch backwards (to secure your stitches).

    • A.

      Stitch patterns

    • B.

      Reverse stitch

    • C.

      Tension guide

    • D.

      Backstitch

    Correct Answer
    D. Backstitch
    Explanation
    The correct answer is "Backstitch". Backstitching is a technique used in sewing that involves stitching backwards to secure the stitches. By stitching in reverse, the machine creates a stronger and more secure seam at the beginning and end of a line of stitches. This prevents the stitches from unraveling or coming undone over time. Backstitching is commonly used in sewing projects to reinforce seams and ensure durability.

    Rate this question:

  • 6. 

    The hole in the needle is called the:

    • A.

      Casing

    • B.

      Opening

    • C.

      Eye

    • D.

      Threader

    Correct Answer
    C. Eye
    Explanation
    The hole in the needle is commonly referred to as the "eye". This is because it is the part of the needle where the thread is passed through in order to sew or stitch. The eye is typically small and located at the opposite end of the needle from the point. It allows the thread to be easily threaded through and held in place while sewing.

    Rate this question:

  • 7. 

    This helps move your fabric through the machine while sewing.

    • A.

      Needle

    • B.

      Presser foot

    • C.

      Feed dogs

    • D.

      Gas pedal

    Correct Answer
    C. Feed dogs
    Explanation
    Feed dogs are small metal teeth located on the sewing machine's surface that help move the fabric through the machine while sewing. They work in coordination with the presser foot to grip and advance the fabric, ensuring smooth and even stitching. The feed dogs move the fabric forward and backward, allowing the needle to penetrate the fabric at the correct intervals. Without the feed dogs, the fabric would not be properly guided and may result in uneven or skipped stitches.

    Rate this question:

  • 8. 

    Sewing supplies are also called:

    • A.

      Stitchery

    • B.

      Notions

    • C.

      Products

    • D.

      Equipment

    Correct Answer
    B. Notions
    Explanation
    The correct answer is "Notions" because sewing supplies are commonly referred to as notions in the sewing industry. Notions include various small items such as buttons, zippers, threads, and other accessories that are used in sewing projects. The term "notions" encompasses a wide range of sewing supplies and is widely recognized among sewers and crafters.

    Rate this question:

  • 9. 

    A seam gauge is...

    • A.

      A long tape used for body measurements

    • B.

      A small ruler used to measure stitches

    • C.

      A small ruler used for small measurements

    • D.

      A large ruler used for large measurements

    Correct Answer
    C. A small ruler used for small measurements
    Explanation
    A seam gauge is a small ruler used for small measurements. It is commonly used in sewing and tailoring to measure small distances accurately, such as hems, seam allowances, and buttonhole placements. The small size of the ruler allows for precise measurements in tight spaces and ensures accuracy in sewing projects.

    Rate this question:

  • 10. 

    A seam ripper is used for:

    • A.

      Taking out stitches

    • B.

      Marking fabric

    • C.

      Holding two pieces of fabric together

    • D.

      Threading the needle

    Correct Answer
    A. Taking out stitches
    Explanation
    A seam ripper is a small tool with a sharp point and a hooked blade that is specifically designed for removing stitches. It is used to carefully cut and remove stitches without damaging the fabric. This tool is commonly used in sewing and garment construction to correct mistakes, alter or repair garments, or to simply remove unwanted stitches.

    Rate this question:

  • 11. 

    Where does the bobbin go in the sewing machine?

    • A.

      Inside the bobbin case

    • B.

      Inside a little door on the lower front part of the machine

    • C.

      On the spool pin

    • D.

      Both A and B

    Correct Answer
    D. Both A and B
    Explanation
    The bobbin goes in both the bobbin case and inside a little door on the lower front part of the sewing machine. The bobbin case is where the bobbin is placed and secured, while the little door on the lower front part of the machine is where the bobbin is accessed and inserted. Both A and B are correct because the bobbin can be found in both of these locations in the sewing machine.

    Rate this question:

  • 12. 

    What is the purpose of the throat plate on a sewing machine?

    • A.

      Holds the needle in place

    • B.

      Supports the fabric during sewing

    • C.

      Regulates thread tension

    • D.

      Guides the fabric under the presser foot

    Correct Answer
    B. Supports the fabric during sewing
    Explanation
    The throat plate, also known as the needle plate, is a flat metal plate located under the needle. It provides a smooth surface for the fabric to rest on and helps guide it as it passes under the presser foot. The throat plate often has markings to indicate seam allowances and stitching guidelines.

    Rate this question:

  • 13. 

    This holds the needle in place.

    • A.

      The needle plate

    • B.

      The needle lever

    • C.

      The needle gauge

    • D.

      The needle clamp

    Correct Answer
    D. The needle clamp
    Explanation
    The needle clamp is responsible for holding the needle in place. It ensures that the needle remains secure and stable during sewing, preventing it from moving or falling out of position. Without the needle clamp, the needle would not be able to perform its function effectively, leading to inaccurate stitching or even machine malfunctions.

    Rate this question:

  • 14. 

    How do you lift the Presser foot up and down?

    • A.

      The hand wheel

    • B.

      The take up lever

    • C.

      The Presser foot lifter

    • D.

      The Presser foot guide

    Correct Answer
    C. The Presser foot lifter
    Explanation
    To lift the Presser foot up and down, you would use the Presser foot lifter. This is a mechanism on the sewing machine that allows you to raise and lower the Presser foot, which is the part that holds the fabric in place while sewing. By using the Presser foot lifter, you can easily adjust the height of the Presser foot to accommodate different fabric thicknesses or to remove and insert fabric. The hand wheel is used to manually move the needle up and down, the take up lever is responsible for controlling the thread tension, and the Presser foot guide helps to guide the fabric as it is being sewn.

    Rate this question:

  • 15. 

    Sewing shears will become dull if used on paper.

    • A.

      True

    • B.

      False

    Correct Answer
    A. True
    Explanation
    Using sewing shears on paper can cause the blades to become dull because paper is abrasive and can cause the edges of the blades to wear down. This can make it difficult to cut fabric cleanly and accurately. Therefore, it is important to avoid using sewing shears on paper to maintain their sharpness and ensure optimal cutting performance.

    Rate this question:

  • 16. 

    Sewing shears are angled to make it easier to cut on a flat surface.

    • A.

      True

    • B.

      False

    Correct Answer
    A. True
    Explanation
    Sewing shears are designed with an angled blade to make it easier for the user to cut fabric on a flat surface. The angle allows for a more comfortable grip and better control while cutting. This design feature helps to ensure precise and accurate cuts, resulting in better sewing and crafting projects.

    Rate this question:

  • 17. 

    What does the term "presser foot" refer to in a sewing machine?

    • A.

      The foot pedal used to control the machine

    • B.

      A part that secures the fabric in place

    • C.

      The part that regulates thread tension

    • D.

      The metal plate under the needle

    Correct Answer
    B. A part that secures the fabric in place
    Explanation
    In a sewing machine, the "presser foot" is a component that holds the fabric flat as it is fed through the machine and stitched. It works in conjunction with the feed dogs, which move the fabric through the machine, ensuring that stitches are even and precise. The presser foot can be raised or lowered as needed to position the fabric and accommodate different thicknesses.

    Rate this question:

  • 18. 

    Where do you place the spool of thread?

    • A.

      On the Spool pin

    • B.

      On the thread guide

    • C.

      On the spool spindle

    • D.

      In the bobbin case

    Correct Answer
    A. On the Spool pin
    Explanation
    The spool of thread should be placed on the spool pin. The spool pin is a small rod or pin that is typically located on the top or side of a sewing machine. It is designed to hold the spool of thread securely in place while the machine is in use. Placing the spool on the spool pin ensures that the thread unwinds smoothly and without tangling during the sewing process.

    Rate this question:

  • 19. 

    Where do you place the bobbin when you need to refill it with thread?

    • A.

      In the bobbin case

    • B.

      On the bobbin winder

    • C.

      On the spool pin

    • D.

      On the backstitch button

    Correct Answer
    B. On the bobbin winder
    Explanation
    When you need to refill the bobbin with thread, you place it on the bobbin winder. The bobbin winder is specifically designed for holding and winding the thread onto the bobbin. This allows for easy and efficient refilling of the bobbin, ensuring that it is ready for use in the sewing machine. Placing the bobbin on the bobbin winder is the correct and appropriate location for refilling it with thread.

    Rate this question:

  • 20. 

    Which way do you turn the hand wheel?

    • A.

      Towards you

    • B.

      Away from you

    • C.

      To the left

    • D.

      To the right

    Correct Answer
    A. Towards you
    Explanation
    The hand wheel is turned towards you in order to operate it. This means that you need to rotate the hand wheel in a clockwise direction when facing it.

    Rate this question:

Matt Balanda |BS (Aerospace Engineering) |
Science Teacher
Matt Balanda, a Calvary Chapel Christian School leader with a Bachelor's in Aerospace Engineering and Mathematics, transitioned from Aerospace Engineering to Education with a Master's from California Baptist University. As the High School Vice-Principal and Physics teacher, he nurtures students' love of learning and faith, creating an enriching and transformational educational experience.

Quiz Review Timeline +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Jul 04, 2024
    Quiz Edited by
    ProProfs Editorial Team

    Expert Reviewed by
    Matt Balanda
  • Aug 29, 2014
    Quiz Created by
    Katrina James
Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.