Scrutineering Quiz (Aditya) 3

1. What is the max allowable deflection in side impact of the car ?

20mm

25mm

20cm

25cm

The maximum allowable deflection in side impact of a car is 25mm. This means that the car's structure should not deform or deflect more than 25mm when subjected to a side impact force. This is an important safety requirement as it ensures that the car's occupants are protected and the structural integrity of the car is maintained during a side collision.

Explanation

The maximum allowable deflection in side impact of a car is 25mm. This means that the car's structure should not deform or deflect more than 25mm when subjected to a side impact force. This is an important safety requirement as it ensures that the car's occupants are protected and the structural integrity of the car is maintained during a side collision.

2. Which of the following materials is acceptable as scatter shield for a chain with a maximum width of 38mm ?

120mm wide, 2mm thick, steel

100mm wide, 5mm thick, steel

120mm wide, 3mm thick, steel

120mm wide, 4mm thick, aluminum

The chain has a maximum width of 38mm, so it can fit within a scatter shield that is 120mm wide. The scatter shield also needs to be strong enough to protect the chain, so it should be made of steel rather than aluminum. Among the options given, the only one that meets both criteria is the scatter shield that is 120mm wide and 3mm thick, made of steel.

Explanation

The chain has a maximum width of 38mm, so it can fit within a scatter shield that is 120mm wide. The scatter shield also needs to be strong enough to protect the chain, so it should be made of steel rather than aluminum. Among the options given, the only one that meets both criteria is the scatter shield that is 120mm wide and 3mm thick, made of steel.

3. What is the minimum radius a main hoop tube can be bent (measured at tube centerline) if the outside diameter is 20mm ?

45mm

78mm

60mm

100mm

20mm

The minimum radius a main hoop tube can be bent is 60mm. This is because the outside diameter of the tube is 20mm, and the minimum radius of the bend should be at least three times the diameter of the tube. Therefore, 20mm x 3 = 60mm.

Explanation

The minimum radius a main hoop tube can be bent is 60mm. This is because the outside diameter of the tube is 20mm, and the minimum radius of the bend should be at least three times the diameter of the tube. Therefore, 20mm x 3 = 60mm.

4. What is the min. gap between heat source and the insulation panel for insulating against convection heat ?

15mm

20mm

25mm

50.8mm

The minimum gap between the heat source and the insulation panel for insulating against convection heat is 25mm. This is because a larger gap allows for better insulation and reduces the transfer of heat through convection. A smaller gap may not provide enough space for proper insulation, leading to heat transfer and reduced effectiveness of the insulation panel.

Explanation

The minimum gap between the heat source and the insulation panel for insulating against convection heat is 25mm. This is because a larger gap allows for better insulation and reduces the transfer of heat through convection. A smaller gap may not provide enough space for proper insulation, leading to heat transfer and reduced effectiveness of the insulation panel.

5. If pneumatic shifter is left in the cost report ,which penalty will be applied ?

Penalty A

Penalty B

Both

No Penalty

Depends on judge

If the pneumatic shifter is left in the cost report, Penalty A will be applied.

Explanation

If the pneumatic shifter is left in the cost report, Penalty A will be applied.

6. What is the load applied on the shoulder harness attachment of the car when an alternative approach is used for the chassis?

11.4 kN

12.8 kN

13.2 kN

15.7kN

not-available-via-ai

Explanation

not-available-via-ai

7. Min height of car number must be___

2 inch

4 inch

6 inch

8 inch

The minimum height of the car number must be 6 inches. This is because car numbers need to be easily visible and legible from a distance, especially for law enforcement and identification purposes. A height of 6 inches ensures that the numbers are large enough to be seen clearly, even from a distance or in poor lighting conditions.

Explanation

The minimum height of the car number must be 6 inches. This is because car numbers need to be easily visible and legible from a distance, especially for law enforcement and identification purposes. A height of 6 inches ensures that the numbers are large enough to be seen clearly, even from a distance or in poor lighting conditions.

8. What is the load applied on front bulkhead along x axis when alternative approach in chassis in frame is used ?

0

170kN

7kN

150kN

Not fixed

The load applied on the front bulkhead along the x-axis when the alternative approach in chassis in frame is used is 150kN.

Explanation

The load applied on the front bulkhead along the x-axis when the alternative approach in chassis in frame is used is 150kN.

9. When submitting the cost report, where do drawings and other supporting material go?

Supporting material should not be submitted, just presented at the visual inspection

In a separate file

In the EBOM file next to the table describing the part

The supporting material is included in the standard cost tables

Only presented during presentation

Drawings and other supporting material should be submitted in a separate file when submitting the cost report.

Explanation

Drawings and other supporting material should be submitted in a separate file when submitting the cost report.

10. What is the min. rating for fire extinguisher which is acceptable at any FSAE event ?

USA 1 A 10BE

Europe 1A 10BC

Australia 10BC

Australia 20 BE

USA 20 BE

Europe 10 BE

The minimum rating for a fire extinguisher that is acceptable at any FSAE event is Australia 20 BE. This means that the fire extinguisher must have a minimum rating of 20 BC for flammable liquid fires and electrical fires. The higher the rating, the more effective the extinguisher is at putting out fires.

Explanation

The minimum rating for a fire extinguisher that is acceptable at any FSAE event is Australia 20 BE. This means that the fire extinguisher must have a minimum rating of 20 BC for flammable liquid fires and electrical fires. The higher the rating, the more effective the extinguisher is at putting out fires.