How Well Do You Understand FSG? Let's Find Out Through This Quiz
-
In autocross, the car at entry is staged such the front tires are ___ behind the starting line.
-
18.7 feet
-
18.9 feet
-
19.3 feet
-
19.7 feet
-
Explore your understanding of Formula Student Germany (FSG) regulations through this engaging quiz. It tests knowledge on safety measures, autocross staging, harness attachment, fire extinguisher requirements, and brake line specifications, essential for compliance and performance in automotive engineering.
Quiz Preview
- 2.
Maximum allowed deflection in the shoulder harness attechment on an application of 12 KN load should be
-
0mm
-
25mm
-
15mm
-
20mm
Correct Answer
A. 0mmExplanation
The maximum allowed deflection in the shoulder harness attachment should be 0mm. This means that when a load of 12 KN is applied, there should be no visible movement or deformation in the shoulder harness attachment. It is crucial for the attachment to remain rigid and secure in order to provide proper support and protection to the user. Any deflection could compromise the effectiveness of the harness and potentially put the user at risk. Therefore, a maximum deflection of 0mm ensures the highest level of safety and reliability.Rate this question:
-
- 3.
Which of the following Aqueous Film Forming Foam (AFFF ) fire extinguisher ratings are allowed?
-
Australia 20BE or 1A 10BE
-
USA, Canada & Brazil: 10BC or 1A 10BC
-
Europe 34B or 5A 34B
-
None of the above
Correct Answer
A. None of the aboveExplanation
The given options mention different fire extinguisher ratings allowed in different countries. However, none of the mentioned ratings match with the correct answer. Therefore, the correct answer is "None of the above."Rate this question:
-
- 4.
The minimum number of full length threads projecting from two lock nuts should be
-
1
-
3
-
4
-
2
Correct Answer
A. 4Explanation
In order to ensure a secure and tight connection, it is recommended to have at least two full length threads engaged between the lock nuts. Since there are two lock nuts mentioned in the question, the minimum number of full length threads projecting from both lock nuts should be four. This ensures proper engagement and prevents loosening or disconnection of the nuts.Rate this question:
-
- 5.
The total lenght of Unarmored brake lines that can be used in the car are
-
0 inch
-
13 inch
-
9 inch
-
7 inch
Correct Answer
A. 13 inchExplanation
The correct answer is 13 inches because it is the only option that provides a length suitable for use in the car's unarmored brake lines. The other options are either too short or nonexistent, making them unsuitable for this purpose. Therefore, 13 inches is the only viable choice for the total length of unarmored brake lines that can be used in the car.Rate this question:
-
- 6.
The allowable STEERING FREEPLAY in a steer by wire system is limited to
-
7
-
9
-
5
-
None of the above
Correct Answer
A. None of the aboveExplanation
The correct answer is "None of the above" because the allowable steering freeplay in a steer by wire system is not limited to any specific number mentioned in the options. The amount of steering freeplay can vary depending on the specific system, manufacturer's specifications, and user preferences.Rate this question:
-
- 7.
From the drivers shoulder rearwards to the mounting piont or structural guide, the shoulder harness must be between ___ degrees above the horizontal and ___ degrees below the horizontal
-
10, 20
-
20, 40
-
30, 50
-
45, 60
Correct Answer
A. 10, 20Explanation
The shoulder harness must be positioned between 10 degrees above the horizontal and 20 degrees below the horizontal. This ensures that the harness is at an appropriate angle to properly restrain the driver's upper body in the event of a collision or sudden stop. This range allows for a comfortable yet secure fit of the shoulder harness.Rate this question:
-
- 8.
The tab to which any harness is attached must have a minimum cross sectional area of ___ of steel to be sheared or failed in tension at any point of the tab.
-
0.075 sq. inch
-
0.062 sq. inch
-
0.068 sq. inch
-
0.059 sq. inch
Correct Answer
A. 0.062 sq. inchExplanation
The correct answer is 0.062 sq. inch. This means that the tab to which any harness is attached must have a minimum cross-sectional area of 0.062 sq. inch of steel in order to be sheared or failed in tension at any point of the tab.Rate this question:
-
- 9.
Teams that are unable to bring a vehicle to the competition ___ participate in the presentation event and will ____ a score for that event
-
Cannot, Receive
-
Can, Will not receive
-
Cannot, Will not receive
-
May, Receive
Correct Answer
A. May, ReceiveExplanation
Teams that are unable to bring a vehicle to the competition may still participate in the presentation event and will receive a score for that event. This means that even if they cannot bring a vehicle, they are still allowed to take part in the presentation event and will be evaluated and given a score based on their performance in that event.Rate this question:
-
- 10.
Two wheels off course at one instance will incur a penalty of ___ seconds
-
20
-
10
-
120
-
0
Correct Answer
A. 0Explanation
If two wheels go off course at the same time, it means that the vehicle has deviated from the designated path. Incurring a penalty of 0 seconds implies that there is no consequence for this action. Therefore, the vehicle can continue without any time penalty for going off course.Rate this question:
-
Quiz Review Timeline (Updated): Oct 25, 2024 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Oct 25, 2024Quiz Edited by
ProProfs Editorial Team -
Jan 12, 2014Quiz Created by
Prvmarketing2014
Back to top