Locksmith Quiz #3
- 1.
The internal wheel pack of a combination lock consists of:
- A.
2 or 3 wheels
- B.
3 or 4 wheels
- C.
4 or 5 wheels
- D.
1 wheel
Correct Answer
B. 3 or 4 wheelsExplanation
p361Rate this question:
-
- 2.
Simplex is a type of:
- A.
Door
- B.
Key
- C.
Lock
- D.
Key machine
Correct Answer
C. LockExplanation
p368Rate this question:
-
- 3.
The main parts of handcuffs are:
- A.
Ratchet, chain and key
- B.
Barrel, pawl and ratchet
- C.
Keyway, pawl and ratchet
- D.
Key, cuffs and keyway
Correct Answer
B. Barrel, pawl and ratchetExplanation
p 355Rate this question:
-
- 4.
What is attached to the bell crank?
- A.
Pawl
- B.
Linkage rod
- C.
Clip
- D.
Door lock
Correct Answer
B. Linkage rodExplanation
p 337Rate this question:
-
- 5.
What does VIN stand for?
- A.
Vehicle Information Number
- B.
Vehicle Identification Number
- C.
Vehicle Insurance Number
- D.
Vehicle Identity Number
Correct Answer
B. Vehicle Identification NumberExplanation
p 313Rate this question:
-
- 6.
You would smoke a key when:
- A.
Illustrating
- B.
Improvising
- C.
Impressioning
- D.
Intimidating
Correct Answer
C. ImpressioningExplanation
p312Rate this question:
-
- 7.
What allows a cylinder to be picked?
- A.
Poor craftmanship of the plug
- B.
Slight spaces and misalignments within a cylinder
- C.
Small spaces and malnourishment
- D.
Worn springs and pins inside the bible
Correct Answer
B. Slight spaces and misalignments within a cylinderExplanation
p 297Rate this question:
-
- 8.
On what type of lock would you usually find a paddle?
- A.
Hookbolt
- B.
Deadlbolt
- C.
Panic bar
- D.
Deadlatch
Correct Answer
D. DeadlatchExplanation
p 285Rate this question:
-
- 9.
Name the functions of a lock. Select all that apply.
- A.
Passage
- B.
Entry
- C.
Storeroom
- D.
Classroom
- E.
Escape
Correct Answer(s)
A. Passage
B. Entry
C. Storeroom
D. Classroom -
- 10.
There are 3 different kinds of safes.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 183 two fire and burglaryRate this question:
-
- 11.
A tubular lock uses a barrel key
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 43Rate this question:
-
- 12.
The bow of a key enters a lock's keyway
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 49Rate this question:
-
- 13.
The most important modern lock development was made by Samuel Segal in 1896
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 10 Yale mortise cylinderRate this question:
-
- 14.
What year did GM stop putting codes on locks?
- A.
1979
- B.
1978
- C.
1975
- D.
1973
Correct Answer
B. 1978Explanation
p 13Rate this question:
-
- 15.
A Variable Speed Drill provides minimal control when drilling into metal.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 17Rate this question:
-
- 16.
3 types of warded locks are still in use today
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 59Rate this question:
-
- 17.
A mortise lock is the oldest lock still currently in use today
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 59 wardedRate this question:
-
- 18.
In figure 6.1 in the disc tumbler lock cross section, where is the spring located?
- A.
Top
- B.
Bottom
- C.
Right side
- D.
Left side
Correct Answer
B. BottomExplanation
p 87Rate this question:
-
- 19.
The Schlage D series key in knob lockset does not have a deadlocking plunger
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 119Rate this question:
-
- 20.
Kaba is a well known manufacturer of High Security Hardware
- A.
True
- B.
False
Correct Answer
A. True -
- 21.
The most popular disc tumbler locks have:
- A.
3 discs
- B.
5 discs
- C.
8 discs
- D.
12 discs
Correct Answer
B. 5 discsExplanation
p 153Rate this question:
-
- 22.
Cross keying occurs when:
- A.
Many keys operate the same lock
- B.
Two or more different keys intentionally operate the same lock
- C.
Two or more keys accidentally operate the same lock
- D.
Two or more of the same keys operate the same lock
Correct Answer
B. Two or more different keys intentionally operate the same lockExplanation
p 157Rate this question:
-
- 23.
The key bitting is a recorded number stamped on the key for identification
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
p 159Rate this question:
-
- 24.
On a Corbin Mortise Lockset (7000, 7500, 8500 series) what tool is recommended if the latchbolt doesn't extend or retract freely when the door is open?
- A.
A file
- B.
A Corbin latch bolt tool
- C.
A knob aligning tool
- D.
A screwdriver
Correct Answer
C. A knob aligning toolExplanation
p 228Rate this question:
-
- 25.
MAG Engineering and Mfg Co created what lock?
- A.
Simplex
- B.
Door o Matic
- C.
Install a lock
- D.
Presto Matic
Correct Answer
C. Install a lockExplanation
p272Rate this question:
-
- 26.
The door adjustment is located on the bottom side of the hinge in a lot of vehicles.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 317 pillarRate this question:
-
- 27.
Codes are present on pre 1970 GM vehicles
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
p 325Rate this question:
-
- 28.
VATS is also know as:
- A.
Passkey
- B.
Passlock
- C.
Onstar
- D.
PATS
Correct Answer
A. PasskeyExplanation
p 327Rate this question:
-
- 29.
An L tool is used to lift a button
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p333Rate this question:
-
- 30.
The J tool is one of the most difficult to use
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
-333Rate this question:
-
- 31.
Some car opening tools have teeth
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
p 335Rate this question:
-
- 32.
A J tool goes under the window
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 339Rate this question:
-
- 33.
The simplest way to open most doors is with an air wedge
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 353Rate this question:
-
- 34.
If a customer is purchasing a padlock from you, what should you ask them?
- A.
Where will the lock be used?
- B.
How many people will have the key?
- C.
How much money do you have?
- D.
What color do you want?
Correct Answer
A. Where will the lock be used? -
- 35.
Lever tumbler locks are high security
- A.
True
- B.
False
Correct Answer
B. False -
- 36.
You will pass your test because:
- A.
It will make you happy
- B.
It will make Tony happy
- C.
What makes Tony happy makes you happy
Correct Answer(s)
A. It will make you happy
B. It will make Tony happy
C. What makes Tony happy makes you happy -
- 37.
In 1979 GM began using fixed pawls on door locks
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
p 13 fordRate this question:
-
- 38.
In 1767 the treatise The Art of the Locksmith was published in:
- A.
Egypt
- B.
England
- C.
Germany
- D.
France
Correct Answer
D. FranceExplanation
p5Rate this question:
-
- 39.
A privacy lockset would most commonly be found on a closet door.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
bathroomRate this question:
-
- 40.
Hardplate is used in safes to prevent drilling attempts
- A.
True
- B.
False
Correct Answer
A. True -
- 41.
Use the space provided to explain why it is important to pass your test on Tuesday.
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 15, 2022Quiz Edited by
ProProfs Editorial Team -
May 06, 2012Quiz Created by
Lockgurl
- Academic Quizzes
- Adult Learning Quizzes
- Blended Learning Quizzes
- Coaching Quizzes
- College Quizzes
- Communication Quizzes
- Curriculum Quizzes
- Distance Learning Quizzes
- E Learning Quizzes
- Early Childhood Education Quizzes
- GCSE Quizzes
- Grade Quizzes
- Graduation Quizzes
- Kindergarten Quizzes
- Knowledge Quizzes
- Literacy Quizzes
- Online Assessment Quizzes
- Online Exam Quizzes
- Online Test Quizzes
- Physical Education Quizzes
- Qualification Quizzes
- Religious Education Quizzes
- School Quizzes
- Special Education Quizzes
- Student Quizzes
- Study Quizzes
- Subject Quizzes
- Teaching Quizzes
- Theory Quizzes
- Thesis Quizzes
- University Quizzes
Back to top