Forklift Operator Jule-art Inc
Forklift Course Test Jule-Art Inc.
Questions and Answers
- 1.
You can stand under the forks, If the engine of the lift truck is turned off?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
It is not safe to stand under the forks of a lift truck, even if the engine is turned off. The forks can still move or fall unexpectedly, posing a serious risk of injury or even death. It is important to follow proper safety protocols and never stand under the forks of a lift truck, regardless of its operational status.Rate this question:
-
- 2.
You can place your hands and feet outside of the operators compartment, as long as your head and body are protected.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that it is allowed to place hands and feet outside the operator's compartment as long as the head and body are protected. However, this is incorrect. In any situation where there is a risk of injury, it is important to keep all body parts within the designated compartment for maximum safety. Placing hands and feet outside the compartment can expose them to potential hazards and increase the risk of accidents. Therefore, the correct answer is false.Rate this question:
-
- 3.
You can drive a lift truck over any kind of surface.
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement suggests that you can drive a lift truck over any kind of surface. However, this is not true. Lift trucks are designed to operate on specific surfaces, such as smooth and level floors. Driving a lift truck on uneven or unstable surfaces can be dangerous and may cause accidents. Therefore, the correct answer is false.Rate this question:
-
- 4.
Whats wrong with this picture?
- A.
Driving in wrong direction
- B.
Load is too high
- C.
Nothing
Correct Answer
A. Driving in wrong directionExplanation
The correct answer is "driving in wrong direction". This suggests that there is an issue with the picture related to the direction in which the vehicle is moving. It implies that the vehicle is going against the flow of traffic or is on the wrong side of the road. This is considered dangerous and against traffic regulations, making it the wrong thing in the picture.Rate this question:
-
- 5.
Before loading or unloading a trailer at a loading dock you should:
- A.
Inspect the floor of the trailer to ensure that it will support the full wieght of lift truck and load
- B.
Chock the wheels of the trailer
- C.
Make sure the dock plates, boards, and ramps are in place and secure
- D.
All Of the above
Correct Answer
D. All Of the aboveExplanation
Before loading or unloading a trailer at a loading dock, it is important to inspect the floor of the trailer to ensure that it can support the weight of the lift truck and load. This is necessary to prevent any accidents or damage to the trailer. Additionally, chocking the wheels of the trailer is necessary to prevent it from moving during the loading or unloading process. Lastly, it is crucial to make sure that the dock plates, boards, and ramps are in place and secure to ensure safe and smooth loading or unloading. Therefore, the correct answer is "all of the above."Rate this question:
-
- 6.
If your truck starts to tip over:
- A.
Dont jump
- B.
Stay in your seat
- C.
Brace yourself with your feet
- D.
All of the above
Correct Answer
D. All of the aboveExplanation
If your truck starts to tip over, it is important not to jump out of the vehicle as this can lead to serious injuries. Instead, it is safer to stay in your seat and brace yourself with your feet. By doing so, you can maintain stability and minimize the risk of getting hurt during the tipping over process. Therefore, the correct answer is "all of the above" as all the mentioned actions should be taken in such a situation.Rate this question:
-
- 7.
Rear wheel stearing is used in lift trucks because it gives the operator greater control when using the forks
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Rear wheel steering is used in lift trucks because it provides the operator with greater control when using the forks. This is because the rear wheel steering allows for tighter turns and better maneuverability, especially in narrow spaces. By being able to steer the rear wheels, the operator can easily navigate around obstacles and position the forks accurately. This enhances the overall efficiency and safety of operating the lift truck.Rate this question:
-
- 8.
If the lift mechanism on your lift truck fails you should try to do the repairs on the chains or hydraulic system yourself
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Attempting to repair the lift mechanism on a lift truck, such as the chains or hydraulic system, by oneself is not recommended. This is because lift trucks are complex machinery and require specialized knowledge and training to handle and repair. Trying to fix the lift mechanism without proper expertise can lead to further damage or even accidents. It is advisable to seek professional help or contact the manufacturer or authorized service personnel to ensure proper repairs and maintain safety standards.Rate this question:
-
- 9.
The most important safety device on your lift truck is
- A.
Horn
- B.
Seat belt
- C.
Warning light
- D.
Back up alarm
- E.
You
Correct Answer
E. YouExplanation
The correct answer is "you" because as the operator of the lift truck, you are responsible for ensuring the safety of yourself and others. You need to be alert, follow proper operating procedures, and make decisions that prioritize safety. While safety devices such as horns, seat belts, warning lights, and back up alarms are important, they are only effective if you use them correctly and pay attention to your surroundings. Ultimately, your actions and awareness play a crucial role in preventing accidents and maintaining a safe working environment.Rate this question:
-
- 10.
The three major parts of a lift truck are the body (truck), overhead guard, and the hydraulic lift
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The statement is true because a lift truck typically consists of three major parts: the body or truck itself, the overhead guard for operator protection, and the hydraulic lift mechanism that allows for the lifting and lowering of loads. These three components are essential for the functioning of a lift truck and are typically found in most models.Rate this question:
-
- 11.
When transporting a load you should not raise your forks more than 8'' from the ground
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
When transporting a load, it is important not to raise the forks more than 8'' from the ground. This is because raising the forks too high can lead to instability and increase the risk of the load falling off or tipping over. By keeping the forks closer to the ground, the load remains more secure and the forklift operator has better control over the load. Therefore, the statement "When transporting a load you should not raise your forks more than 8'' from the ground" is true.Rate this question:
-
- 12.
It is safe for you to give someone a ride on your lift truck
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
It is not safe to give someone a ride on a lift truck. Lift trucks are designed to carry loads, not passengers. Allowing someone to ride on a lift truck can pose serious safety risks, including the risk of falling off or being struck by objects. It is important to follow proper safety protocols and guidelines when operating lift trucks to ensure the safety of everyone involved.Rate this question:
-
- 13.
When parking or leaving your truck you should
- A.
Park or leave your truck in a safe area away from traffic
- B.
Lower the forks untill they are flat on the floor
- C.
Turn off engine
- D.
Set the parking brake and set direction control to neutral
- E.
All of the above
Correct Answer
E. All of the aboveExplanation
When parking or leaving your truck, it is important to follow certain safety measures. Parking or leaving the truck in a safe area away from traffic ensures that it will not obstruct the flow of vehicles and reduces the risk of accidents. Lowering the forks until they are flat on the floor prevents any potential hazards or damage. Turning off the engine helps conserve fuel and prevent unnecessary emissions. Setting the parking brake and setting the direction control to neutral ensures that the truck remains stationary and prevents any unintended movement. Therefore, all of the above actions should be taken when parking or leaving your truck.Rate this question:
-
- 14.
The load capacity of a lift truck can be found on its data plate
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The load capacity of a lift truck can be found on its data plate. This means that the data plate provides information about the maximum weight that the lift truck can safely carry. By referring to the data plate, operators can ensure that they do not exceed the load capacity, which is crucial for maintaining safety and preventing accidents. Therefore, the statement "true" is correct as the load capacity of a lift truck can indeed be found on its data plate.Rate this question:
-
- 15.
All idustrial lift trucks are equipped with a clutch
- A.
True
- B.
False
Correct Answer
B. False -
- 16.
The front wheels of a lift truck serve as the ___________________________ between the weight of the truck and the weight of the load bieng carried
- A.
Balance point
- B.
Fulcrum point
- C.
Center of gravity
- D.
See saw center
Correct Answer
B. Fulcrum pointExplanation
The front wheels of a lift truck serve as the fulcrum point between the weight of the truck and the weight of the load being carried. This means that the front wheels act as the pivot point or the point of support for the weight distribution. By positioning the load in front of the front wheels, the weight is balanced and the truck can be maneuvered effectively without tipping over.Rate this question:
-
- 17.
The gauge shown to the right is a/an
- A.
Gas gauge
- B.
Amperes gauge
- C.
Oil gauge
- D.
Total hour meter
- E.
None of the above
Correct Answer
E. None of the above -
- 18.
Wide and long loads are more unstable than other types of loads
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Wide and long loads are more unstable than other types of loads because their size and shape make them more prone to tipping or shifting during transportation. The increased width and length create a larger surface area, making it easier for external forces such as wind or uneven terrain to affect the load's stability. Additionally, the weight distribution of wide and long loads can be more challenging to manage, increasing the risk of imbalance and potential accidents. Therefore, it is true that wide and long loads are more unstable than other types of loads.Rate this question:
-
- 19.
All industrial lift trucks are equipped with controls that allow you to raise / lower and tilt the forks
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Industrial lift trucks are indeed equipped with controls that enable the operator to raise or lower the forks and also to tilt them. These controls are essential for the efficient and safe operation of the lift truck, allowing the operator to adjust the height and angle of the forks according to the specific needs of the task at hand. By having these controls, the lift truck can effectively handle and transport loads of different sizes and shapes, ensuring smooth and secure material handling operations.Rate this question:
-
- 20.
Of the three images shown below which is the most stable?
- A.
1
- B.
2
- C.
3
Correct Answer
C. 3 -
- 21.
Anyone who has a valid drivers licsence can operate a lift truck
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is false because not just anyone with a valid driver's license can operate a lift truck. Operating a lift truck requires specialized training and certification beyond just having a driver's license. Therefore, the statement is incorrect.Rate this question:
-
- 22.
Which of the following should NOT be allowed during the re-fueling or re-charging process
- A.
Park your truck in a designated re-fueling / re-charging area
- B.
Do not block doorways or emergency exits or equipment
- C.
Keep a flame nearby to burn away any unwanted vapors or gasses
- D.
Check to see a fire extinguisher is nearby
Correct Answer
C. Keep a flame nearby to burn away any unwanted vapors or gassesExplanation
During the re-fueling or re-charging process, it is important to prioritize safety. Keeping a flame nearby to burn away unwanted vapors or gases is highly dangerous and should not be allowed. It can lead to explosions or fires, posing a risk to both the vehicle and the individuals involved in the process. It is crucial to follow proper safety protocols and guidelines to prevent accidents and ensure a safe environment during re-fueling or re-charging.Rate this question:
-
- 23.
It is your job to inspect the brakes, hydrualic lift system, the tires, and load prior to operating your lift truck every single day
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The statement indicates that it is the responsibility of the individual to inspect the brakes, hydraulic lift system, tires, and load before operating a lift truck every day. This implies that performing these inspections is a necessary step to ensure the safe operation of the lift truck. Therefore, the answer "true" is correct.Rate this question:
-
- 24.
A brake pedal that slowly sinks all the way to the floor is in good operating condition
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
A brake pedal that slowly sinks all the way to the floor is not in good operating condition. This could indicate a potential issue with the brake system, such as a leak in the brake lines or a faulty master cylinder. It is important for the brake pedal to be firm and responsive in order to ensure proper braking performance and safety while driving.Rate this question:
-
- 25.
In order to solve an "inch pound equation" you must use informationprovided on the data plate
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
To solve an "inch pound equation," it is necessary to use the information provided on the data plate. This suggests that the data plate contains crucial details or values that are required to solve the equation accurately. Therefore, the statement is true as it highlights the importance of the data plate in solving inch pound equations.Rate this question:
-
- 26.
Lift trucks use a hydrualic cylinder attatched to chains to raise and lower the forks
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Lift trucks commonly use a hydraulic cylinder attached to chains to raise and lower the forks. This mechanism allows the forks to be adjusted to the desired height for lifting and transporting loads. The hydraulic cylinder uses fluid pressure to move the chains, which in turn raises or lowers the forks. This system provides the necessary power and control for efficient and precise lifting operations.Rate this question:
-
- 27.
Which of the following is NOT a type of lift truck?
- A.
Gasoline powered
- B.
Diesel powered
- C.
Air cooled powered
- D.
Electric powered
Correct Answer
C. Air cooled poweredExplanation
The question asks for the option that is NOT a type of lift truck. "Air cooled powered" does not refer to a type of lift truck. The other options, namely gasoline powered, diesel powered, and electric powered, are all types of lift trucks commonly used in various industries.Rate this question:
-
- 28.
Always check air pressure on tires from the side, not by facing the tread
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
When checking the air pressure on tires, it is important to do so from the side rather than by facing the tread. This is because the tread may give a false impression of the tire's pressure due to wear and tear. By checking the air pressure from the side, one can get a more accurate reading and ensure that the tires are properly inflated for optimal performance and safety.Rate this question:
-
- 29.
During extreme hot / cold days when its difficult to maintain building temperature while taking loads through the bay doors you should
- A.
Open the bay door as wide as possible and leave it open while you perform your tasks
- B.
Jump of your lift truck and open the door, go through the door, jump off the lift truck and close the door every single time you go through
- C.
Stage your work as much as possible,open the bay door then take all your loads through and close the door
- D.
Wait untill the tempeture is more normal
Correct Answer
C. Stage your work as much as possible,open the bay door then take all your loads through and close the doorExplanation
During extreme hot/cold days when it's difficult to maintain building temperature while taking loads through the bay doors, staging the work as much as possible is the correct answer. This means opening the bay door, taking all the loads through, and then closing the door. By doing this, the door is not left open for extended periods, minimizing the amount of hot or cold air entering the building. This helps to maintain the desired temperature inside the building and reduces the strain on the HVAC system.Rate this question:
-
- 30.
As a certified fork lift operator at Jule-Art it is your responsibility to load / unload and sign for materials when they come in if there are no supervisors around
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
As a certified forklift operator at Jule-Art, it is indeed the responsibility of the operator to load/unload materials and sign for them when they arrive, especially if there are no supervisors present. This ensures proper documentation and accountability for the materials being received.Rate this question:
-
- 31.
when signing for materials you MUST account for everthing you are signing for, date and sign the packing list, and turn them in to the production manager
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The given statement is true because when signing for materials, it is important to account for everything that is being signed for. This includes checking the items received against the packing list, ensuring that everything is accounted for. Additionally, it is necessary to date and sign the packing list as a confirmation of receipt. Finally, the signed packing list should be turned in to the production manager for further processing and record-keeping. Failing to follow these steps can lead to discrepancies and difficulties in tracking inventory and managing production processes.Rate this question:
-
Back to top