Delta 1000 Semi Electric Bed By Drive

The correct answer is that Drive marks the shaft with either Semi or Full over the appropriate hole. This means that Drive uses a labeling system to indicate which hole should be used. The labels "Semi" and "Full" likely correspond to specific measurements or specifications, allowing the user to easily identify the correct hole to use based on their needs or requirements.

The correct answer is aligning bed springs in a 90-degree angle and connecting C hooks the same way as all other home care beds. This method ensures that the head spring and foot spring are properly connected, providing stability and support to the bed. Welds and glue are not suitable options for connecting the springs as they may not provide the necessary strength and durability.

The batter back up can be located in either the hand control or the motor case, indicating that it requires a battery that can fit in either of these locations. Out of the given options, only the 9 volt battery is small enough to fit in both the hand control and the motor case. Therefore, the correct answer is 9 volt.

The correct answer is "the same as all other major manufacturers." This means that when installing the head and foot boards on the bed with the motor, you would follow the same process as other well-known manufacturers in the industry. It implies that there is a standard procedure or method that is commonly used by all major manufacturers for installing these components.

The explanation for the given correct answer is that attaching the Hilo shaft to the frame of the bed makes it easier to install on the headboards and foot boards. This is because you no longer have to stand at one side of the bed and fish it through. Instead, you can just lift the spring sections and the Hilo shaft is hanging in place, simplifying the installation process.

The statement suggests that the Delta bed drives come with a telescoping Hilo shaft that does not need to be removed once it is assembled for the first time. This implies that the telescoping Hilo shaft is a permanent feature of the Delta bed drives and does not require any additional adjustments or removal. Therefore, the answer is true.

The correct answer suggests that to fix a Drive bed that is not rising evenly due to incorrect assembly with 2 head boards or 2 foot boards, one should simply move the hilo shaft from the head to foot board setting to the head to head or foot to foot setting on the transition box. This implies that the issue is caused by the incorrect positioning of the hilo shaft, and by moving it to the correct setting, the bed will rise evenly.

The Drive Delta bed made it simple to correctly place the spring-loaded cross bars for full side rails by implementing multiple features. Firstly, they color-coded the springs black, which helps in easily identifying and placing them correctly. Secondly, they notched the bed frame, providing clear indications of where the cross bars should be positioned. Lastly, they added a label, which further assists in ensuring the proper placement of the cross bars. Therefore, all of the above features contribute to making it easier to correctly place the spring-loaded cross bars for full side rails.

The correct answer is "On the same side as the transition box." This means that when placing the Hilo shaft through the hanger bracket on the footspring during initial assembly, the locking collar should be on the same side as the transition box. This ensures proper alignment and functioning of the components.

The explanation for the given correct answer is that installing the motor on the Drive Delta bed can be done while the bed is still up on its side. The process involves removing the siding covers from the motor case, aligning the inlets to the hooks on the actuator bars, and giving the motor a firm push until it clicks onto the hooks. Afterward, the covers can be replaced by sliding them back on. This process is described as a way to install the motor on the bed, indicating that the statement is true.

The correct answer is YES, you can now use any manufacturers head and foot boards on a drive bed deck. This means that you are not limited to using only Drive, Invacare, or Medline head and foot boards on a Drive bed deck. You have the flexibility to use head and foot boards from any manufacturer to assemble a working bed.

The correct answer is "Up" because when the motor is installed, the two humps on it should face upwards. This is because the humps are designed to provide stability and support to the motor, and having them facing upwards ensures that the motor is properly aligned and secured in its position. Facing the humps downwards could lead to instability and potential damage to the motor.

After assembling the frame, the next logical step would be to extend the shaft and install the motor. This is because the shaft is an essential component that connects the motor to the frame, allowing it to operate and provide the necessary movement. By extending the shaft and installing the motor, the bed or machine would be ready for use. The other options, such as installing the headboard, footboard, or wheels, can be done after the motor is in place as they are not directly related to the functioning of the machine.