Bay Path Sabre Saw
-
The student should check that the ________ is being used for the cut and that it is properly installed.
-
Right power
-
Proper blade
-
Curve design
-
Hard material
-
The 'Bay Path Sabre Saw' quiz assesses key safety measures for operating a sabre saw. It covers checking the switch position, blade selection, and proper handling techniques to prevent accidents and equipment damage. This quiz is essential for learners in vocational training or industrial settings.
Quiz Preview
- 2.
The student must check that there is sufficient electrical cord length to ________.
-
Cut atleast half way
-
Cut the full thickness
-
Complete the cut
-
Have a reserve coil
Correct Answer
A. Complete the cutExplanation
The student must check that there is sufficient electrical cord length to complete the cut. This means that the cord should be long enough to allow for the entire cutting process without running out of length. If the cord is too short, the student may not be able to finish the cut and may need to find a longer cord or extension to complete the task.Rate this question:
-
- 3.
The student must make sure that the blade does not come into contact with the ________ during the cutting operation.
-
Bench
-
Material
-
Cord
-
Machine
Correct Answer
A. CordExplanation
During the cutting operation, it is important for the student to ensure that the blade does not come into contact with the cord. This is because the cord can get tangled in the blade, causing accidents or damage to the equipment. Keeping the blade away from the cord ensures safe and efficient cutting.Rate this question:
-
- 4.
The student should check that the ________ is in the off position before plugging the saw into the power outlet.
-
Motor
-
Power
-
Machine
-
Switch
Correct Answer
A. SwitchExplanation
Before plugging the saw into the power outlet, the student should check that the switch is in the off position. This is important to ensure safety and prevent any accidental activation of the saw's motor. By confirming that the switch is off, the student can avoid any potential hazards or injuries that may occur if the saw were to unexpectedly turn on while being plugged in.Rate this question:
-
- 5.
The blade must not touch the material when the power is turned on. Turning on the power with the blade touching the material can ________.
-
Increase the rate of the cut
-
Slow down the cut
-
Break the blade
-
Burn out the saw
Correct Answer
A. Break the bladeExplanation
When the power is turned on and the blade is touching the material, it creates a lot of friction and resistance. This can cause excessive strain on the blade, leading to it breaking. The force exerted by the blade against the material can be too much for it to handle, causing it to snap or fracture. Therefore, it is important to ensure that the blade does not touch the material when the power is turned on to prevent any damage or breakage.Rate this question:
-
- 6.
Do not cut the radius so small that it binds or bends the blade. This may cause the blade to ________.
-
Cut unevenly
-
Stop
-
Come loose
-
Break
Correct Answer
A. BreakExplanation
Cutting a radius that is too small and causes the blade to bind or bend can lead to excessive stress on the blade. This increased stress can ultimately cause the blade to break.Rate this question:
-
- 7.
Do not saw into the ________.
-
Material
-
Supporting work surface
-
Fence
-
Guard
Correct Answer
A. Supporting work surfaceExplanation
The phrase "do not saw into the supporting work surface" suggests that one should avoid cutting or damaging the surface that is providing support or stability for the task at hand. This cautionary statement is likely referring to a situation where sawing or cutting is taking place, and it is important to be mindful of not causing any harm to the surface that is aiding in the process.Rate this question:
-
- 8.
The student should place the saw base plate ________ the material to be cut before turning the power.
-
1 inch from
-
Firmly on
-
1/2 inch above
-
1/2 inch below
Correct Answer
A. Firmly onExplanation
The student should place the saw base plate firmly on the material to be cut before turning the power. This is important because placing the base plate firmly on the material ensures stability and prevents the saw from slipping or moving during the cutting process. It also helps to maintain accuracy and control while cutting.Rate this question:
-
- 9.
Be sure ________ before changing blades or doing any adjustments to the sabre saw.
-
The correct blade is available
-
The saw is plugged into the power source
-
The right parts are available
-
The saw is unplugged from the power source
Correct Answer
A. The saw is unplugged from the power sourceExplanation
Before changing blades or making any adjustments to the sabre saw, it is important to ensure that the saw is unplugged from the power source. This is crucial for the safety of the person handling the saw, as it eliminates the risk of accidental starting or electrocution. By unplugging the saw, one can be certain that there is no power running to the tool, making it safe to work on.Rate this question:
-
Quiz Review Timeline (Updated): Mar 22, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 22, 2023Quiz Edited by
ProProfs Editorial Team -
Feb 01, 2013Quiz Created by
Mahonray
Back to top