Bay Path Circular Saw
-
If the portable circular saw has a three-prong plug, make sure each prong is in good working condition and ________.
-
Is green in color
-
Not broken off or loose
-
Two-prongs are loose
-
The ground prong is missing
-
The 'Bay Path Circular Saw' quiz assesses knowledge on safe handling and maintenance of portable circular saws. It covers plug condition, blade guard functionality, blade suitability, cutting depth settings, stock support, and proper saw placement before operation, essential for safety and efficiency in tool usage.
Quiz Preview
- 2.
The saw must be unplugged from the power source when ________.
-
Changing the blade
-
Adjusting depth of cut
-
Doing any adjustments
-
A,b,and c
Correct Answer
A. A,b,and cExplanation
When changing the blade, adjusting the depth of cut, or doing any adjustments on the saw, it is necessary to unplug it from the power source. This is important to ensure safety and prevent any accidental activation of the saw while working on it.Rate this question:
-
- 3.
If the cutoff piece of stock is unsupported, caution must be used so that when it falls, the stock does not cause ________.
-
Injury to the operator
-
Injury to other students
-
Damaged to cut stock
-
A,b,and c
Correct Answer
A. A,b,and cExplanation
If the cutoff piece of stock is unsupported, caution must be used so that when it falls, the stock does not cause injury to the operator, injury to other students, or damage to the cut stock.Rate this question:
-
- 4.
Before starting your cutting operation, make sure the electric power cord will not come in contact with ________.
-
The stock you are cutting
-
The moving blade
-
Nails in the material
-
Scrap material
Correct Answer
A. The moving bladeExplanation
Before starting your cutting operation, it is important to ensure that the electric power cord will not come in contact with the moving blade. This is because the moving blade can be sharp and powerful, posing a risk of cutting through the cord and causing electrical hazards such as electric shock or short circuits. It is crucial to keep the cord away from the blade's path to maintain a safe working environment.Rate this question:
-
- 5.
The portable circular saw is designed to cut ________ which can be square or beveled from the top surface of the stock to be cut.
-
Only radius lines
-
Only three inch circles
-
Only 1/8 to 1/4 inch radius lines
-
Only straight lines
Correct Answer
A. Only straight linesExplanation
The portable circular saw is designed to cut only straight lines. It is not designed to cut radius lines or circles of any specific size. The purpose of a circular saw is to make straight cuts in various materials such as wood, metal, or plastic. It is a versatile tool that can be adjusted to cut at different angles, but its primary function is to cut in a straight line.Rate this question:
-
- 6.
Every student must obtain permission from the instructor ________ the portable circular saw.
-
Prior to using
-
After using
-
During the cutting operation of
-
After the students plugs in
Correct Answer
A. Prior to usingExplanation
In order to use the portable circular saw, every student must obtain permission from the instructor beforehand. This implies that the permission should be acquired before using the saw, indicating that the correct answer is "prior to using".Rate this question:
-
- 7.
Place the saw on the stock to be cut ________ and lined up with the cut line on the stock, before the power is turned on.
-
With the blade clear of the stock
-
With your hands holding the stock
-
So that the blade is touching the stock
-
With the blade at least 5 inches from the stock
Correct Answer
A. With the blade clear of the stock -
- 8.
When using portable electric power equipment, always check to see that you have ________ to complete the job.
-
Ample length of power cord
-
Ample supply of blades
-
Enough stock
-
Enough support
Correct Answer
A. Ample length of power cordExplanation
When using portable electric power equipment, it is important to have an ample length of power cord to complete the job. This is because the power cord is what connects the equipment to the power source, allowing it to function properly. Without a sufficient length of power cord, the equipment may not be able to reach the desired area, limiting its usability and effectiveness. Therefore, ensuring that there is enough power cord available is crucial for successfully completing the job.Rate this question:
-
- 9.
Check the blade for ________.
-
The correct saw set
-
Kick back
-
Correct color
-
The proper cutting application for the job
Correct Answer
A. The proper cutting application for the jobExplanation
When checking the blade, it is important to ensure that it is suitable for the specific cutting application required for the job. Different blades are designed for different materials and cutting techniques, so using the proper blade will ensure efficient and effective cutting. Checking the blade for the proper cutting application helps to prevent damage to the blade, avoid accidents, and achieve the desired results.Rate this question:
-
- 10.
Make sure ________ before plugging the stock into the power source.
-
The blade is tightened
-
To check the extention cord
-
The switch is in the off position
-
The master switch is on
Correct Answer
A. The switch is in the off positionExplanation
Before plugging the stock into the power source, it is important to ensure that the switch is in the off position. This is necessary to prevent any accidental activation of the stock, which could potentially lead to injuries or damage. By checking and confirming that the switch is off, one can safely proceed with plugging the stock into the power source.Rate this question:
-
- 11.
The blade guard must revolve up into the upper guard assembly ________.
-
Without sticking or binding
-
When the switch is turned on
-
At all times
-
Only when the blade moves
Correct Answer
A. Without sticking or bindingExplanation
The blade guard must revolve up into the upper guard assembly without sticking or binding to ensure smooth and unhindered movement. This is important for the safety and proper functioning of the tool. If the blade guard sticks or binds, it can cause accidents or interfere with the cutting process. Therefore, it is necessary for the blade guard to move freely without any obstruction or resistance.Rate this question:
-
- 12.
Before starting a cutting operation, you should set the proper cutting depth at ________ the thickness of the stock you are cutting.
-
1/16 inch below
-
1/2 inch below
-
1/8 inch above
-
1/8 inch below
Correct Answer
A. 1/16 inch belowExplanation
Before starting a cutting operation, it is important to set the proper cutting depth. Setting the cutting depth at 1/16 inch below the thickness of the stock being cut ensures that the blade cuts through the material without going too deep. This helps to prevent damage to the stock and ensures a clean and precise cut.Rate this question:
-
- 13.
All stock must be supported so that the rotating gaurd ________ during the complete cutting operation.
-
Will keep a straight cut
-
Will not bind and move freely
-
Will keep the blade sharp
-
Will reduce saw dust
Correct Answer
A. Will not bind and move freelyExplanation
The correct answer is "will not bind and move freely". This means that in order for the rotating guard to function effectively during the cutting operation, the stock must be supported in a way that prevents it from getting stuck or obstructed and allows it to move smoothly without any restrictions.Rate this question:
-
Quiz Review Timeline (Updated): Mar 21, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Feb 01, 2013Quiz Created by
Mahonray