Csx Operating Rules 100 Questions
-
Which of the following describes Medium Speed?
-
A speed not exceeding 15 MPH
-
A speed not exceeding 30 MPH.
-
A speed not exceeding 45 MPH.
-
A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car, an obstruction, on-track equipment or a stop signal.
-
The 'CSX Operating Rules 100 Questions' quiz assesses knowledge of railroad safety protocols and operational rules. It covers restricted and controlled speeds, handling of multi-level auto-rack equipment, and speed regulations under various track and traffic conditions, crucial for ensuring safety in railroad operations.
Quiz Preview
- 2.
A Red Sign is observed to the right of the main track. What is the name of this sign and what does it indicate?
-
Warning Sign - prepare to reduce speed or stop, limits as directed.
-
Temporary Reduce Speed Sign - Reduce Speed Indicated.
-
Temporary End Restriction Sign - Resume speed after rear of train has passed.
-
Conditional STOP Sign - Stop before entering limits, unless permission to enter limits is obtained.
Correct Answer
A. Conditional STOP Sign - Stop before entering limits, unless permission to enter limits is obtained.Explanation
The sign described in the question is a Conditional STOP Sign. This sign indicates that a train should stop before entering the limits, unless permission to enter those limits is obtained.Rate this question:
-
- 3.
Which of the following is the responsibility of the conductor?
-
The supervision of the operation and administration of the train.
-
Consulting with the engineer if any doubts arise concerning the authority for proceeding or safety.
-
Notifying the engineer of restrictions imposed by dispatcher message or instructions not more than five (5) miles but not less than two (2) before reaching them.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The conductor is responsible for supervising the operation and administration of the train, consulting with the engineer if any doubts arise regarding authority or safety, and notifying the engineer of any restrictions imposed by dispatcher messages or instructions. All of these responsibilities are part of the conductor's role.Rate this question:
-
- 4.
What is the maximum authorized speed for trains operating against the current of traffic or when the signal system is suspended?
-
49 MPH freight, 59 MPH passenger.
-
59 MPH for freight and passenger.
-
70 MPH for freight and passenger.
-
60 MPH freight, 70 MPH passenger.
Correct Answer
A. 49 MPH freight, 59 MPH passenger.Explanation
When trains are operating against the current of traffic or when the signal system is suspended, the maximum authorized speed is 49 MPH for freight trains and 59 MPH for passenger trains.Rate this question:
-
- 5.
Which of the following describes Slow Speed?
-
A speed not exceeding 15 MPH.
-
A speed not exceeding 30 MPH.
-
A speed not exceeding 45 MPH.
-
A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car, an obstruction, on-track equipment or a stop signal.
Correct Answer
A. A speed not exceeding 15 MPH.Explanation
Slow speed is defined as a speed not exceeding 15 MPH. This means that the maximum speed allowed in this case is 15 miles per hour. It is important to adhere to this speed limit in order to ensure safety and control while driving. Going beyond this speed may increase the risk of accidents and make it difficult to stop within a short distance. Therefore, it is crucial to maintain a slow speed when necessary, such as when approaching a train, car, obstruction, on-track equipment, or a stop signal.Rate this question:
-
- 6.
What flagging signals are required to be carried in the leading engine and the last car of a passenger train?
-
Not less than 12 torpedoes, 6 red fusees and a red flag.
-
Not less than 6 red fusees and a red flag.
-
At least 1 red fusee and a red flag.
-
All of these answers are correct.
Correct Answer
A. Not less than 6 red fusees and a red flag. -
- 7.
Which of the following is the responsibility of the engineer?
-
Operating the engine safely and efficiently and the proper handling of the train.
-
Assuming the responsibilities of the conductor when there is no conductor on the train or if the conductor is disabled.
-
The safety of the train and the observance of the rules, jointly with the conductor.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The engineer is responsible for operating the engine safely and efficiently, ensuring the proper handling of the train. They also assume the responsibilities of the conductor when there is no conductor on the train or if the conductor is disabled. Additionally, the engineer is responsible for the safety of the train and the observance of the rules, working in conjunction with the conductor. Therefore, all of the given answers accurately describe the responsibilities of an engineer.Rate this question:
-
- 8.
Which of the following is the responsibility of all crew members?
-
Ensure that the train is safely operated and rules are observed by assuming as much responsibility as possible to prevent accidents or rule violations.
-
Conductors and engineers are responsible for the safety of the train and observance of the rules, so other employees are relieved of this responsibility.
-
Obeying the conductor's instructions, even if these instructions endanger the safety of the train or violates the rules.
-
All of these answers are correct.
Correct Answer
A. Ensure that the train is safely operated and rules are observed by assuming as much responsibility as possible to prevent accidents or rule violations.Explanation
All crew members are responsible for ensuring the safe operation of the train and the observance of rules. They should assume as much responsibility as possible to prevent accidents or rule violations. This means that they should actively contribute to the safety of the train and follow all necessary procedures and guidelines. This responsibility is shared among all crew members, including conductors and engineers, and is not solely assigned to specific individuals.Rate this question:
-
- 9.
Which of the following documents must be carried by each employee whose assignment requires them to enter or use controlled tracks?
-
Operating Rules and Timetable Special Instructions.
-
System Bulletins.
-
General Bulletins.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
All employees whose assignment requires them to enter or use controlled tracks must carry the Operating Rules and Timetable Special Instructions, System Bulletins, and General Bulletins. These documents provide important information and instructions regarding the operation and use of controlled tracks, ensuring the safety and efficiency of employees working in these areas.Rate this question:
-
- 10.
What is required if a train encounters a Conditional Stop Sign that is not covered by a dispatcher message or EC-1, or is at a location designated by an expired or annuled dispatcher message or EC-1 Instruction?
-
Proceed prepared to stop in two miles. If no Conditional Stop Sign or Temporary Reduce Speed Sign is encountered in two miles, proceed at controlled speed for an additional mile, then proceed at authorized speed, unless otherwise restricted.
-
Reduce to controlled speed not exceeding 10 MPH as soon as sign is seen. Speed may by increased if released by train dispatcher, or after the leading end passes a point two miles after passing the sign, or the rear of the train passes a Temporary End Restriction Sign.
-
Stop immediately, notify the dispatcher and be governed by instructions received.
-
All of these answers are correct.
Correct Answer
A. Stop immediately, notify the dispatcher and be governed by instructions received.Explanation
If a train encounters a Conditional Stop Sign that is not covered by a dispatcher message or EC-1, or is at a location designated by an expired or annulled dispatcher message or EC-1 Instruction, the required action is to stop immediately, notify the dispatcher, and be governed by instructions received. This means that the train must come to a halt, inform the dispatcher about the situation, and follow any further instructions given by the dispatcher.Rate this question:
-
- 11.
- When must an emergency call ("Emergency, Emergency, Emergency") be made?
-
To cover initial reports of derailments or collisions.
-
After trainline initiated emergencies.
-
Storms, washouts, fires, obstructions to track and other hazardous conditions that could cause damage to property or injury.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
An emergency call must be made in all of the mentioned situations because they all involve potential risks to property or injury. Initial reports of derailments or collisions, trainline initiated emergencies, storms, washouts, fires, obstructions to track, and other hazardous conditions are all serious situations that require immediate attention and response. Making an emergency call in these situations is essential to ensure the safety of the people involved and to mitigate any further damage or harm.Rate this question:
- 12.
Which of the following describes Limited Speed?
-
A speed not exceeding 15 MPH
-
A speed not exceeding 30 MPH.
-
A speed not exceeding 45 MPH.
-
A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car, an obstruction, on-track equipment or a stop signal.
Correct Answer
A. A speed not exceeding 45 MPH.Explanation
Limited speed refers to a speed that does not exceed a certain limit. In this case, the correct answer is "A speed not exceeding 45 MPH." This means that the speed should not go beyond 45 miles per hour. It is important to adhere to this limit to ensure safety on the road and to be able to stop within a reasonable distance in case of any obstacles or hazards.Rate this question:
-
- 13.
When rules and instructions conflict, which of the following describes the proper order that documents supercede the instructions found in the remaining documents?
-
Special instructions in the timetable (supercede instructions in....), System and General Bulletins, Dispatcher messages and Form EC-1 instructions.
-
Form EC-1 instructions (supercede instructions in....), Dispatcher messages, System and General Bulletins, and Special Instructions in the timetable.
-
Dispatcher messages (supercede instructions in....) Special instructions in the timetable System and General Bulletins, and Form EC-1 instructions.
-
System and General Bulletins (supercede instructions in...), Special instructions in the timetable, Form EC-1 instructions and Dispatcher messages.
Correct Answer
A. Form EC-1 instructions (supercede instructions in....), Dispatcher messages, System and General Bulletins, and Special Instructions in the timetable.Explanation
According to the given answer, Form EC-1 instructions take precedence over all other documents. After that, Dispatcher messages are considered, followed by System and General Bulletins, and finally Special Instructions in the timetable. This order indicates that Form EC-1 instructions have the highest authority, and the other documents are ranked in descending order of importance.Rate this question:
-
- 14.
What must a crewmember in the operating cab of an engine announce by radio?
-
The name and location of each block and controlled point signal.
-
The train's entry and departure into or from each TWC authority, and passenger train arrival and departure at passenger stations.
-
Train entrance into a passing siding and when stopping, and each 15 minutes after being stopped on a main track or passing siding.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The correct answer is that all of these answers are correct. A crewmember in the operating cab of an engine must announce the name and location of each block and controlled point signal, the train's entry and departure into or from each TWC authority and passenger train arrival and departure at passenger stations, and the train's entrance into a passing siding and when stopping, as well as every 15 minutes after being stopped on a main track or passing siding.Rate this question:
-
- 15.
A Yellow Sign with a diagonal Orange stripe is observed to the right of a main track. What is the name of this sign and what does it indicate?
-
Warning Sign - Prepare to reduce speed or stop, limits as directed.
-
Temporary Reduce Speed Sign - Reduce Speed Indicated.
-
Temporary End Restriction Sign - Resume speed after rear of train has passed.
-
Conditional STOP Sign - Stop before entering limits, unless permission to enter limits is obtained.
Correct Answer
A. Warning Sign - Prepare to reduce speed or stop, limits as directed.Explanation
The correct answer is "Warning Sign - Prepare to reduce speed or stop, limits as directed." This sign is called a warning sign and it indicates that the train should prepare to reduce speed or stop, following the limits as directed.Rate this question:
-
- 16.
If a train is approaching the limits of a Form W that is not yet in effect and it cannot get the head end of the train clear of the limits before the Form W becomes effective, how must it be governed?
-
Do not enter the limits unless the roadway worker in charge, named in the Form W, grants permission to enter the limits, which may be given prior to the effective time.
-
Proceed at the Restricted Speed until the trailing end of the movement reaches the end of the Form W limits.
-
Stop immediately, notify the dispatcher and be governed by instructions received.
-
All of these answers are correct.
Correct Answer
A. Do not enter the limits unless the roadway worker in charge, named in the Form W, grants permission to enter the limits, which may be given prior to the effective time.Explanation
If a train is approaching the limits of a Form W that is not yet in effect and it cannot get the head end of the train clear of the limits before the Form W becomes effective, it must not enter the limits unless the roadway worker in charge, named in the Form W, grants permission to enter the limits, which may be given prior to the effective time. This ensures that the train does not enter the limits without proper authorization and maintains safety protocols.Rate this question:
-
- 17.
What actions are required when a train that is moving and an emergency application of the brakes occur?
-
Immediately initiate an emergency radio transmission.
-
Notify the train dispatcher of the train ID, location of the head end after stopping, mile post location one train length preceding the emergency brake application and if there are any adjacent tracks.
-
Provide warning for any adjacent track the train until is is known that tracks are not obstructed or relieved by train dispatcher.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
When a train that is moving and an emergency application of the brakes occur, all of the mentioned actions are required. The train operator should immediately initiate an emergency radio transmission to alert the relevant authorities. They should also notify the train dispatcher about the train ID, location of the head end after stopping, mile post location one train length preceding the emergency brake application, and any adjacent tracks. Additionally, they should provide warning for any adjacent track until it is confirmed that the tracks are not obstructed or relieved by the train dispatcher.Rate this question:
-
- 18.
Which of the following describes Restricted Speed?
-
A speed not exceeding 15mph.
-
A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car , an obstruction, on-track equipment or a stop signal.
-
A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car, an obstruction, a stop signal, a derail or an improperly lined switch. It must permit looking out for broken rail. It will not exceed 15mph.
-
A speed that will permit stopping within one-half the range of vision, short of a train, a car, an obstruction, a derail or an improperly lined switch, on-track equipment or a stop signal.
Correct Answer
A. A speed that will permit stopping within one-half the range of vision. It will also permit stopping short of a train, a car, an obstruction, a stop signal, a derail or an improperly lined switch. It must permit looking out for broken rail. It will not exceed 15mph.Explanation
Restricted Speed is a speed that allows the train to stop within one-half the range of vision. It also allows the train to stop short of a train, car, obstruction, stop signal, derail, or improperly lined switch. In addition, the train must be able to look out for broken rail. The speed must not exceed 15mph.Rate this question:
-
- 19.
What is required if the headlight on the lead engine fails en route, when both auxillary (ditch) lights are inoperative?
-
The bell must be rung continuously while train is moving and horn sounded frequently.
-
The speed must be reduced when necessary, but not exceeding 20 MPH over public highway-rail crossings.
-
A white light must be used in its place at night.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The correct answer is that all of these answers are correct. If the headlight on the lead engine fails en route and both auxiliary (ditch) lights are inoperative, it is required to ring the bell continuously while the train is moving and sound the horn frequently. Additionally, the speed must be reduced when necessary, but not exceeding 20 MPH over public highway-rail crossings. Finally, a white light must be used in place of the headlight at night.Rate this question:
-
- 20.
Where is a Red Sign located?
-
At least two miles before the restriction.
-
At least two miles after the restriction.
-
On each end of the working limits.
-
At the end of the restriction.
Correct Answer
A. On each end of the working limits.Explanation
The correct answer is "On each end of the working limits." This means that a red sign is located at both ends of the area where work is being done or where there are restrictions. This is important for drivers to be aware of the working limits and to proceed with caution when approaching or passing through these areas.Rate this question:
-
- 21.
Where is a Yellow Sign with a diagonal Orange stripe located?
-
At least one mile before the restriction.
-
At least two miles before the restriction.
-
At the beginning of the restriction.
-
At the end of the restriction.
Correct Answer
A. At least two miles before the restriction.Explanation
A Yellow Sign with a diagonal Orange stripe is located at least two miles before the restriction. This sign serves as a warning to drivers that there is a restriction ahead, such as a construction zone or a hazard. By placing the sign two miles in advance, it gives drivers ample time to adjust their speed, change lanes, or take any necessary precautions before reaching the restriction. This helps to ensure the safety of both drivers and workers in the restricted area.Rate this question:
-
- 22.
What actions must employees take if they observe that a train fails to actuate a signal to display the proper aspect, or if an improper signal aspect permitting a train to proceed is observed?
-
Stop the train.
-
Attempt to stop other trains involved.
-
Notify the train dispatcher.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
Employees must take all of the mentioned actions if they observe that a train fails to actuate a signal to display the proper aspect or if they observe an improper signal aspect permitting a train to proceed. They should stop the train, attempt to stop other trains involved, and notify the train dispatcher.Rate this question:
-
- 23.
Which of the following describes the term Dispatcher Bulletin?
-
Information contained in Timetables, System Bulletins, General Bulletins, and CSX Procedural Instruction Manual.
-
A computer generated form issued by a train dispatcher. It contains current operating instructions applying to the train addressed. It also contains information as to the latest System and General Bulletins issued.
-
Written or electronically transmitted special instructions concerning the safety of employees and the movement of trains issued by the Operating Rules Department.
-
A computer-generated form advising of a dispatcher bulletin number and the number of train messages it must contain. Its address must correspond to the associated dispatcher bulletin.
Correct Answer
A. A computer generated form issued by a train dispatcher. It contains current operating instructions applying to the train addressed. It also contains information as to the latest System and General Bulletins issued.Explanation
A Dispatcher Bulletin is a computer-generated form issued by a train dispatcher that contains current operating instructions for the train it is addressed to. It also provides information about the latest System and General Bulletins issued. This form serves as a means of communication between the train dispatcher and the train, ensuring that the train has the necessary instructions and is aware of any updates or changes in operating procedures.Rate this question:
-
- 24.
How are movements to be made after a train receives a Flash Flood Warning, in the territory specified?
-
All trains must operate through these limits not exceeding 40 mph.
-
If unusual heavy rain or high water is encountered within these limits, all trains must approach bridges, culverts and other points likely to be affected at restricted speed.
-
The train dispatcher must be notified promptly when conditions that may affect the safe movement of trains are observed.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
After a train receives a Flash Flood Warning in the specified territory, there are several movements that need to be made to ensure safety. First, all trains must operate through the limits specified, but not exceeding 40 mph. This is to ensure that the trains can maintain control and react to any potential hazards. Additionally, if unusual heavy rain or high water is encountered within these limits, all trains must approach bridges, culverts, and other points likely to be affected at restricted speed. This allows for cautious navigation and reduces the risk of accidents. Lastly, it is important to notify the train dispatcher promptly when conditions that may affect the safe movement of trains are observed. This ensures that appropriate actions can be taken to mitigate any potential dangers. Therefore, all of these answers are correct.Rate this question:
-
- 25.
Which of the following are mandatory directives?
-
Dispatcher message.
-
TWC or DTC authority.
-
Form EC-1 Line 1 Authority: On-Track Equipment movement or Track Work.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
All of the given options are mandatory directives. The Dispatcher message is a directive that provides instructions or information to train crews. TWC or DTC authority refers to Track Warrant Control or Direct Traffic Control authority, which are both mandatory directives used to authorize train movements on a specific track. Form EC-1 Line 1 Authority is another mandatory directive that authorizes On-Track Equipment movement or Track Work. Therefore, all of these answers are correct as they all represent mandatory directives.Rate this question:
-
- 26.
What is the maximum authorized speed for trains handling multi-level auto-rack equipment, including Amtrak's Auto Train?
-
49 MPH.
-
59 MPH.
-
70 MPH.
-
79 MPH.
Correct Answer
A. 70 MPH.Explanation
The maximum authorized speed for trains handling multi-level auto-rack equipment, including Amtrak's Auto Train, is 70 MPH.Rate this question:
-
- 27.
Which of the following describes an auxiliary track for meeting or passing trains, where block signals govern train movements?
-
Signaled Siding.
-
Controlled Siding.
-
Yard Limits.
-
Auxiliary Track.
Correct Answer
A. Signaled Siding.Explanation
A signaled siding refers to an auxiliary track where block signals are used to control train movements. This means that trains can meet or pass each other on this track while adhering to the signals displayed. The block signals ensure safe and efficient train operations by indicating when it is safe for trains to enter or exit the siding. Controlled siding, yard limits, and auxiliary track do not specifically mention the use of block signals for train movements, making signaled siding the most appropriate choice.Rate this question:
-
- 28.
A Yellow Sign is observed to the right of the main track. What is the name of this sign and what does it indicate?
-
Warning Sign-Prepare to reduce speed or stop, limits as directed.
-
Temporary Reduce Speed Sign-Reduce speed indicated.
-
Temorary Edn Restriction Sign-Resume speed after rear of train has passed.
-
Conditional STOP Sign-Stop before entering limits, unless permission to enter limits is obtained.
Correct Answer
A. Temporary Reduce Speed Sign-Reduce speed indicated.Explanation
The correct answer is the Temporary Reduce Speed Sign, which indicates that the speed should be reduced as indicated. This sign is typically used in temporary situations where there may be hazards or work being done on or near the track. It serves as a warning to train operators to slow down and proceed with caution.Rate this question:
-
- 29.
When required by the rules to provide warning against approaching trains, what is the minimum distance that an employee equipped with flagging equipment must go, where the authorized track speed is between 41 and 90 MPH?
-
1/2 mile.
-
1 mile.
-
1 1/2 miles.
-
2 miles.
Correct Answer
A. 1 1/2 miles.Explanation
An employee equipped with flagging equipment must go a minimum distance of 1 1/2 miles when required to provide warning against approaching trains with an authorized track speed between 41 and 90 MPH. This distance ensures that there is enough time for the approaching train to see the warning and slow down or stop if necessary, ensuring the safety of both the employee and the train.Rate this question:
-
- 30.
A train that is within the limits of a Form w (Rule 89 Work Limits) has made a scheduled station stop. How must is proceed?
-
It may proceed, subject to any speed restrictions previously received from the employee in charge.
-
It must not make further movement until permission to move has been received from the employee in charge.
-
It may proceed at controlled speed not exceeding 20 MPH until the head end reaches the far limits.
-
All of these answers are correct.
Correct Answer
A. It must not make further movement until permission to move has been received from the employee in charge.Explanation
The correct answer is "It must not make further movement until permission to move has been received from the employee in charge." This means that even though the train is within the limits of a Form w, it cannot proceed without permission from the employee in charge. This ensures safety and coordination between the train and the employee in charge.Rate this question:
-
- 31.
In DTC-Track Warrant territory, what must the train dispatcher specify when granting block authority?
-
Engine initials/number, direction of movement and total number of blocks.
-
The name of the block(s) and type of block authority.
-
The authority number.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The train dispatcher must specify all of these details when granting block authority in DTC-Track Warrant territory. This includes the engine initials/number, direction of movement, and total number of blocks. Additionally, the dispatcher must provide the name of the block(s) and type of block authority, as well as the authority number.Rate this question:
-
- 32.
What is required when a train encounters an unattended fusee, burning on or near its track?
-
Stop until the fusee burns out, then proceed at restricted speed for one mile.
-
Immediately reduce to restricted speed for one mile.
-
Immediately reduce to restricted speed for 15 minutes.
-
Immediately reduce to controlled speed for 15 minutes.
Correct Answer
A. Immediately reduce to restricted speed for 15 minutes.Explanation
When a train encounters an unattended fusee burning on or near its track, the required action is to immediately reduce to restricted speed for 15 minutes. This means that the train must slow down and maintain a specific speed limit for a duration of 15 minutes to ensure safety and prevent any potential accidents or damage. This allows the train to proceed cautiously and be prepared to take further action if necessary.Rate this question:
-
- 33.
What is required when mandatory directives have been annulled, fulfilled or canceled?
-
They must be immediately destroyed.
-
They must be clearly marked with an "X" and retained for 7 days.
-
They must be clearly marked with an "X" and retained for the remainder of that train's trip.
-
They must be clearly marked with an "X" and retained for the remainder of that crew's tour of duty.
Correct Answer
A. They must be clearly marked with an "X" and retained for 7 days.Explanation
When mandatory directives have been annulled, fulfilled, or canceled, they must be clearly marked with an "X" and retained for 7 days. This allows for a record of the directive to be kept for a limited period of time in case it needs to be referenced or reviewed within that timeframe.Rate this question:
-
- 34.
Which of the following describes the term System Bulletin?
-
Information contained in Timetables, System Bulletins, General Bulletins, and CSX Procedural Instruction Manual.
-
A computer generated form issued by a train dispatcher. It contains current operating instructions applying to the train addressed. It also contains information as to the latest System and General Bulletins issued.
-
Written or electronically transmitted special instructions concerning the safety of employees and the movement of trains issued by the Operating Rules Department.
-
A computer-generated form advising of a dispatcher bulletin number and the number of train messages it must contain. Its address must correspond to the associated dispatcher bulletin.
Correct Answer
A. Written or electronically transmitted special instructions concerning the safety of employees and the movement of trains issued by the Operating Rules Department.Explanation
A System Bulletin refers to written or electronically transmitted special instructions that are issued by the Operating Rules Department. These instructions are specifically related to the safety of employees and the movement of trains. System Bulletins provide important information and guidelines to ensure the safe operation of trains and the well-being of employees. They are an essential part of the communication and coordination process within the railway system.Rate this question:
-
- 35.
How must the crew of a passenger train be governed when inspecting for an overheated bearing?
-
Use a Tempilstik applied on the bearing housing to make a visible mark at least 3 inches long.
-
Report the results of the inspection to the train dispatcher.
-
Attach a completed Hot Bearing Tag to the equipment near the bearing.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The crew of a passenger train must be governed in multiple ways when inspecting for an overheated bearing. First, they should use a Tempilstik to apply a visible mark on the bearing housing, ensuring that the mark is at least 3 inches long. This allows them to easily identify any overheating. Second, they should report the results of the inspection to the train dispatcher, keeping them informed of any potential issues. Lastly, they should attach a completed Hot Bearing Tag to the equipment near the bearing, providing a clear indication that the bearing has been inspected and may require attention. All of these actions are necessary and correct for a thorough inspection.Rate this question:
-
- 36.
Which of the following describes the term Special Instruction?
-
Information contained in Timetables, System Bulletins, General Bulletins, and CSX Procedural Instruction Manual.
-
A computer generated form issued by a train dispatcher. It contains current operating instructions applying to the train addressed. It also contains information as to the latest System and General Bulletins issued.
-
Written or electronically transmitted special instructions concerning the safety of employees and the movement of trains issued by the Operating Rules Department.
-
A computer-generated form advising of a dispatcher bulletin number and the number of train messages it must contain. Its address must correspond to the associated dispatcher bulletin.
Correct Answer
A. Information contained in Timetables, System Bulletins, General Bulletins, and CSX Procedural Instruction Manual.Explanation
Special Instruction refers to the information contained in Timetables, System Bulletins, General Bulletins, and the CSX Procedural Instruction Manual. It does not refer to a computer-generated form issued by a train dispatcher, written or electronically transmitted special instructions concerning safety and train movement, or a computer-generated form advising of a dispatcher bulletin number and train messages. The correct answer is the first option as it accurately describes the term Special Instruction.Rate this question:
-
- 37.
What is required if a train encounters a Temporary Reduce Speed Sign that is not covered by instructions?
-
Proceed prepared to stop in two miles. If no Conditional Stop Sign or Temporary Reduce Speed Sign is encountered in two miles, proceed at controlled speed for an additional mile, then proceed at authorized speed, unless otherwise restricted.
-
Reduce to controlled speed not exceeding 10 MPH as soon as sign is seen. Speed may be increased if released by train dispatcher, or after the leading end passes a point two miles after passing the sign, or the rear of the train passes a Temporary End Restriction Sign.
-
Stop immediately, notify the dispatcher and be governed by instructions received.
-
All of these answers are correct.
Correct Answer
A. Reduce to controlled speed not exceeding 10 MPH as soon as sign is seen. Speed may be increased if released by train dispatcher, or after the leading end passes a point two miles after passing the sign, or the rear of the train passes a Temporary End Restriction Sign.Explanation
When a train encounters a Temporary Reduce Speed Sign that is not covered by instructions, it should reduce its speed to a controlled speed not exceeding 10 MPH as soon as the sign is seen. The train may increase its speed if released by the train dispatcher, or after the leading end passes a point two miles after passing the sign, or when the rear of the train passes a Temporary End Restriction Sign. This ensures that the train proceeds with caution and follows any additional instructions or restrictions that may be in place.Rate this question:
-
- 38.
How must a train be governed when a signal that is imperfectly displayed is encountered, or if a fixed signal is absent from the place where it is usually displayed?
-
Regard the signal as if it was displaying Stop.
-
Regard the signal as if it was displaying Stop and Proceed.
-
Regard the signal as if it was displaying Restricted Proceed.
-
Regard the signal as if it was displaying the most restrictive indication that can be conveyed by that signal.
Correct Answer
A. Regard the signal as if it was displaying the most restrictive indication that can be conveyed by that signal.Explanation
When encountering an imperfectly displayed signal or when a fixed signal is absent, the train should regard the signal as if it was displaying the most restrictive indication that can be conveyed by that signal. This means that the train should assume the signal is displaying the most severe instruction, such as a Stop indication. By doing so, the train ensures maximum safety and avoids any potential risks or accidents that may arise from misinterpreting the signal's actual intention.Rate this question:
-
- 39.
When the signal system is temporarily suspended, which of the following is required of trains moving within the limits of the signal suspension, unless otherwise specified?
-
Stop at drawbridges and railroad crossings at grade and be governed by rules or special instructions in effect for that particular location.
-
Approach all absolute signals prepared to stop, and not pass these signals without permission of the train dispatcher.
-
Approach all public crossings at grade that are equipped with automatic grade crossing warning devices prepared to stop unless the warning devices are operating.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
When the signal system is temporarily suspended, trains moving within the limits of the signal suspension are required to stop at drawbridges and railroad crossings at grade and be governed by rules or special instructions in effect for that particular location. They must also approach all absolute signals prepared to stop and not pass these signals without permission from the train dispatcher. Additionally, trains must approach all public crossings at grade that are equipped with automatic grade crossing warning devices prepared to stop unless the warning devices are operating. All of these requirements are necessary when the signal system is temporarily suspended.Rate this question:
-
- 40.
When is permission always required to make a reverse movement?
-
Permission must be obtained from the roadway worker-in-charge when within work limits.
-
Permission must be obtained from the train dispatcher when the rear of the movement is stopped between the home signals of a controlled point or railroad crossing at grade.
-
Permission must be obtained from the train dispatcher when a train is authorized in TWC territory to move in one direction, or when reverse movement will go beyond the limits of the signal block in any signaled territory.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
In all of the given scenarios, permission is required to make a reverse movement. When within work limits, permission must be obtained from the roadway worker-in-charge. When the rear of the movement is stopped between the home signals of a controlled point or railroad crossing at grade, permission must be obtained from the train dispatcher. Additionally, when a train is authorized in TWC territory to move in one direction, or when a reverse movement will go beyond the limits of the signal block in any signaled territory, permission must also be obtained from the train dispatcher. Therefore, all of the given answers are correct.Rate this question:
-
- 41.
When trains are using other than main or signaled tracks, what is the maximum speed permitted?
-
10 MPH on other than main tracks, or signaled tracks.
-
25 MPH on non-signaled sidings.
-
15 MPH through hand-operated turnouts and crossovers to and from the main track, unless equipped with a signal - 10 MPH through other hand-operated turnouts.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The question asks about the maximum speed permitted when trains are using tracks other than the main or signaled tracks. The given options provide different speed limits for different scenarios. The first option states that the maximum speed permitted on tracks other than main or signaled tracks is 10 MPH. The second option states that the maximum speed permitted on non-signaled sidings is 25 MPH. The third option states that the maximum speed permitted through hand-operated turnouts and crossovers to and from the main track is 15 MPH, unless equipped with a signal, in which case the speed limit is 10 MPH. Since all of these options provide correct information about the maximum speed limits in different situations, the correct answer is that all of these answers are correct.Rate this question:
-
- 42.
When may a train assist another train?
-
The engine performing such service must first be detached from its train.
-
If assisting engine is used to push another train, air hoses must be coupled, angle cocks opened and the automatic brake valve of the assisting engine must have its automatic brake valve cut out.
-
Trains carrying passengers must not be shoved by a helper engine.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
The question is asking when a train may assist another train. The given options state that the assisting engine must first be detached from its train, if it is used to push another train, the air hoses must be coupled and angle cocks opened, and the automatic brake valve of the assisting engine must have its automatic brake valve cut out. It also mentions that trains carrying passengers must not be shoved by a helper engine. The correct answer states that all of these answers are correct, meaning that all of these conditions must be met in order for a train to assist another train.Rate this question:
-
- 43.
When radios are used in connection with switching, backing or pushing a train or engine, if movement is stopped because it has traveled one-half of the specified direction without receiving any additional instructions, or there was doubt about the meaning of the instructions, when may the movement resume?
-
After an additional job briefing is conducted and all concerned understand the move to be made.
-
After additional instructions are received.
-
After radio communication is re-established, or hand signal to proceed is given.
-
After lunch.
Correct Answer
A. After an additional job briefing is conducted and all concerned understand the move to be made.Explanation
When radios are used in connection with switching, backing or pushing a train or engine, if movement is stopped because it has traveled one-half of the specified direction without receiving any additional instructions, or there was doubt about the meaning of the instructions, the movement may resume after an additional job briefing is conducted and all concerned understand the move to be made. This ensures that everyone involved is aware of the intended action and can proceed safely and efficiently.Rate this question:
-
- 44.
In ABS or CPS signaled territory, how may an engine be permitted to enter a block occupied by a standing, in order to assist the standing train?
-
A Form EC-1 must be issued preventing the standing train from moving.
-
A clear understanding must exist between both crews as to the location of the standing train.
-
The assisting engine will stop 1/4 mile from the standing train and approach the location of the standing train at restricted speed.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
All of these answers are correct. In ABS or CPS signaled territory, when an engine needs to enter a block occupied by a standing train to assist it, several precautions need to be taken. Firstly, a Form EC-1 must be issued to prevent the standing train from moving. Secondly, there must be a clear understanding between both crews about the location of the standing train. Lastly, the assisting engine must stop 1/4 mile from the standing train and approach its location at restricted speed. All of these measures ensure the safe entry and assistance of the engine in the occupied block.Rate this question:
-
- 45.
How must a passenger train be governed if it is routed to a track for a station stop when a main track or controlled siding is between the train and the station platform?
-
It may proceed into the station at restricted speed but may not enter the station if another movement is seen approaching or is stopped at the station.
-
It must stop before arriving at the station and obtain assurance from the train dispatcher that protection for passengers crossing the track is being provided.
-
It may enter the station. Other trains must not pass between it and the station platform.
-
All of these answers are correct.
Correct Answer
A. It must stop before arriving at the station and obtain assurance from the train dispatcher that protection for passengers crossing the track is being provided.Explanation
When a passenger train is routed to a track for a station stop and there is a main track or controlled siding between the train and the station platform, it must stop before arriving at the station. The train must then obtain assurance from the train dispatcher that protection for passengers crossing the track is being provided. This is necessary to ensure the safety of passengers and prevent any potential accidents or collisions with other trains.Rate this question:
-
- 46.
Where do General Signal Rules apply?
-
Only where ABS rules are in effect.
-
Only where CPS rules are in effect.
-
They apply in ABS and CPS territory.
-
They apply only in Rule 251 and 261 territory.
Correct Answer
A. They apply in ABS and CPS territory.Explanation
The correct answer is "They apply in ABS and CPS territory." This means that the General Signal Rules are applicable in areas where both ABS (Automatic Block Signal) and CPS (Centralized Traffic Control) rules are in effect. It implies that these rules are specific to certain territories where these two signaling systems are utilized for train operations.Rate this question:
-
- 47.
Before acting on a mandatory directive, which crew members of a train must have a written copy?
-
The engineer only.
-
The conductor only.
-
The conductor and engineer.
-
All crew members.
Correct Answer
A. The conductor and engineer.Explanation
Before acting on a mandatory directive, both the conductor and the engineer of a train must have a written copy. This ensures that both key crew members are aware of and can follow the necessary instructions and procedures. It is important for both individuals to have access to the written copy to ensure effective communication and coordination during the operation of the train.Rate this question:
-
- 48.
When information that is required to be copied is transmitted to a train or moving equipment, when must the movement be stopped?
-
When receiving or copying it on moving equipment could impair safety.
-
To permit an employee operating the equipment to copy or repeat it.
-
When the information to be transmitted will restrict the movement within 3 miles.
-
All of these answers are correct.
Correct Answer
A. All of these answers are correct.Explanation
All of the given answers are correct. When information that is required to be copied is transmitted to a train or moving equipment, the movement must be stopped in order to ensure safety. This is because receiving or copying the information on moving equipment could impair safety. Additionally, the movement must be stopped to permit an employee operating the equipment to copy or repeat the information. Lastly, if the information to be transmitted will restrict the movement within 3 miles, the movement must be stopped. Therefore, all of these answers are correct.Rate this question:
-
- 49.
Which crew members of a train must read and understand mandatory directives?
-
The engineer only.
-
The conductor only.
-
The conductor and engineer.
-
All crew members.
Correct Answer
A. All crew members.Explanation
All crew members of a train must read and understand mandatory directives. This is because these directives contain important information and instructions that are crucial for the safe operation of the train. It is necessary for all crew members, including both the conductor and engineer, to be familiar with these directives to ensure that they can effectively carry out their respective roles and responsibilities. Therefore, the correct answer is that all crew members must read and understand mandatory directives.Rate this question:
-
Quiz Review Timeline (Updated): Mar 21, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 21, 2023Quiz Edited by
ProProfs Editorial Team -
Oct 29, 2012Quiz Created by
Dastump