Zick Compressor Station Ssop Operator Qualification 2020

1. How many ESD pull buttons are located in Phase 2 compressor building?

5

3

27

12

There are 12 ESD pull buttons located in the Phase 2 compressor building.

Explanation

There are 12 ESD pull buttons located in the Phase 2 compressor building.

2. Match the following

Operations Technician

Employees

Supervisor of Operations

Submit

3. Section 8.0 refers to Startup After Emergency Shut Down (ESD)

True

False

Section 8.0 does not refer to Startup After Emergency Shut Down (ESD), so the statement is false.

Explanation

Section 8.0 does not refer to Startup After Emergency Shut Down (ESD), so the statement is false.

4. Section 10.0 Refers to _____

Section 10.0 refers to Operating Limits and Deviations. This section likely provides information and guidelines regarding the acceptable operating limits and deviations for a specific system or process. It may outline the parameters within which the system or process can operate safely and effectively, as well as any allowable deviations from those limits. Understanding this section is important for ensuring that the system or process is operated within its designated limits to prevent any potential issues or failures.

Explanation

Section 10.0 refers to Operating Limits and Deviations. This section likely provides information and guidelines regarding the acceptable operating limits and deviations for a specific system or process. It may outline the parameters within which the system or process can operate safely and effectively, as well as any allowable deviations from those limits. Understanding this section is important for ensuring that the system or process is operated within its designated limits to prevent any potential issues or failures.

Submit

5. Montana Penton has reviewed this SSOP document on which date(s)

6-30-2017

12-31-2019

4-13-2018

11-27-2016

Montana Penton reviewed the SSOP document on two dates: 6-30-2017 and 4-13-2018.

Explanation

Montana Penton reviewed the SSOP document on two dates: 6-30-2017 and 4-13-2018.

Submit

6. Appendix A refers to ?

FCVs

LCVs

PSVs

Appendix A refers to PSVs, which stands for Public Service Vehicles. This term is commonly used to refer to vehicles that are used for public transportation purposes, such as buses, minibusses, or taxis. Appendix A likely contains information, regulations, or guidelines specific to PSVs, such as licensing requirements, safety standards, or operational procedures.

Explanation

Appendix A refers to PSVs, which stands for Public Service Vehicles. This term is commonly used to refer to vehicles that are used for public transportation purposes, such as buses, minibusses, or taxis. Appendix A likely contains information, regulations, or guidelines specific to PSVs, such as licensing requirements, safety standards, or operational procedures.

7. The effective date of this procedure is ?

1-1-2020

12-12-2019

4-15-2014

6-13-2016

There isn't one

The effective date of this procedure is 12-12-2019.

Explanation

The effective date of this procedure is 12-12-2019.

8. Station discharge gas moisture content must remain below 7lbs of water per million standard cubic feet (MMSCF)

True

False

The statement is stating that the moisture content of the gas discharged from the station must be below 7lbs of water per million standard cubic feet (MMSCF). The answer "True" means that this statement is correct and the moisture content of the discharged gas must indeed remain below the specified limit.

Explanation

The statement is stating that the moisture content of the gas discharged from the station must be below 7lbs of water per million standard cubic feet (MMSCF). The answer "True" means that this statement is correct and the moisture content of the discharged gas must indeed remain below the specified limit.

9. Under normal operation, gas enters the facility through what two size pipelines?

12" and 20"

10" and 16"

8" and 20"

20" and 24"

The correct answer is 12" and 20". This means that under normal operation, gas enters the facility through pipelines of two different sizes, namely 12" and 20".

Explanation

The correct answer is 12" and 20". This means that under normal operation, gas enters the facility through pipelines of two different sizes, namely 12" and 20".

10. Two SSOP best practices are?

Print 10 copies to have on hand at the station

Read all appropriate actions carefully prior to beginning the given task

Disregard all said cautions/warnings

Observe symbols and their associated messages

The two SSOP best practices are to read all appropriate actions carefully prior to beginning the given task and to observe symbols and their associated messages. These practices ensure that the task is performed correctly and safely. Reading the actions carefully helps in understanding the steps involved and any precautions that need to be taken. Observing symbols and their associated messages helps in interpreting visual cues and understanding any warnings or instructions related to the task. These best practices promote efficiency, accuracy, and safety in performing SSOP tasks.

Explanation

The two SSOP best practices are to read all appropriate actions carefully prior to beginning the given task and to observe symbols and their associated messages. These practices ensure that the task is performed correctly and safely. Reading the actions carefully helps in understanding the steps involved and any precautions that need to be taken. Observing symbols and their associated messages helps in interpreting visual cues and understanding any warnings or instructions related to the task. These best practices promote efficiency, accuracy, and safety in performing SSOP tasks.

Submit

11. During the normal start up of Compressor Unit 8- what is the permissive fluid set point for Jacket Water?

100 degrees F

125 degrees F

150 degrees F

There is no temperature set point

The permissive fluid set point for Jacket Water during the normal start-up of Compressor Unit 8 is 150 degrees F. This means that the Jacket Water temperature needs to reach or exceed 150 degrees F in order for the start-up process to proceed.

Explanation

The permissive fluid set point for Jacket Water during the normal start-up of Compressor Unit 8 is 150 degrees F. This means that the Jacket Water temperature needs to reach or exceed 150 degrees F in order for the start-up process to proceed.

Submit

13. The warning label in Section 3.9.12 refers to observing speed restrictions posted on the CAT panel- True/False?

True

False

The warning label in Section 3.9.12 refers to observing speed restrictions posted on the CAT panel. This means that there is indeed a warning label in Section 3.9.12 that specifically pertains to the importance of following speed restrictions displayed on the CAT panel. Therefore, the statement "True" is the correct answer.

Explanation

The warning label in Section 3.9.12 refers to observing speed restrictions posted on the CAT panel. This means that there is indeed a warning label in Section 3.9.12 that specifically pertains to the importance of following speed restrictions displayed on the CAT panel. Therefore, the statement "True" is the correct answer.