Oklahoma Locksmith Practice Test

44 Questions | Attempts: 1159
Share

SettingsSettingsSettings
Circle Quizzes & Trivia

.


Questions and Answers
  • 1. 
    What joins a mortise cylinder to a mortise lock? 
    • A. 

      Threads on the cylinder and a set screw

    • B. 

      Screws

    • C. 

      Scalp plate

    • D. 

      Clamps

  • 2. 
    1. The key shown above matches the locks manufactured by: (Diagram not shown here)
    • A. 

      Weslock

    • B. 

      Kwikset

    • C. 

      Schlage

    • D. 

      Dexster

  • 3. 
    What type of key normally must be duplicated with an end mill cutter? 
    • A. 

      Paracentric

    • B. 

      Skeleton

    • C. 

      Tubular

    • D. 

      Bit

  • 4. 
    What is needed to remove the outside knob of a Schlage entrance set? 
    • A. 

      Key and pin punch

    • B. 

      Leather hammer and small wire

    • C. 

      Pin punch and leather hammer

    • D. 

      Key and screwdriver

  • 5. 
    A licensee who moves or changes employers shall notify the Oklahoma Department of Labor within how many days?
    • A. 

      3

    • B. 

      5

    • C. 

      10

    • D. 

      14

  • 6. 
    A technician is weak, having chills and cannot seem to get enough to drink. What is the likely cause of the technician’s symptoms? 
    • A. 

      Stroke

    • B. 

      Dehydration

    • C. 

      Low blood sugar

    • D. 

      High blood sugar

  • 7. 
    The Oklahoma Alarm and Locksmith Industry Act applies to:
    • A. 

      State employees engaged in the performance of official duties

    • B. 

      Individuals who own and install alarm devices on their own property

    • C. 

      Work performed by individuals licensed pursuant to the Electrical License Act

    • D. 

      Persons who sell, install and service alarm systems

  • 8. 
    What type of tumbler is most commonly used in a file cabinet lock?
    • A. 

      Master pin

    • B. 

      Long wafer

    • C. 

      Pin tumbler

    • D. 

      Short water

  • 9. 
    What is the maximum amount of administrative fines that can be levied against any person for violations of the Oklahoma Alarm and Locksmith Industry Act? 
    • A. 

      $200

    • B. 

      $500

    • C. 

      $1,000

    • D. 

      $7,500

  • 10. 
    A coordinator is required on a pair of fire doors having: 
    • A. 

      An open back strike

    • B. 

      An overlapping astragal

    • C. 

      Manual flush bolts

    • D. 

      Fusible link louvers

  • 11. 
    With proper care, which cutter material typically provides the longest use? 
    • A. 

      Carbon steel

    • B. 

      High speed steel

    • C. 

      Carbide

    • D. 

      Cobalt

  • 12. 
    Thru-bolt trim is used on many mortise locks to:
    • A. 

      Require either a flexible head or concealed shell cylinder

    • B. 

      Make the installation look better

    • C. 

      Strengthen the installation and minimize binding

    • D. 

      Allow use of either knob or lever trim with the same lock body

  • 13. 
    If a conflict exists between adopted references, the reference that applies shall be the one: 
    • A. 

      With the more stringent standard

    • B. 

      That is adopted by the OSFM

    • C. 

      That is adopted by the local jurisdiction

    • D. 

      Used by the AHJ

  • 14. 
    What brand of lock does a WR3 or 1054WB key blank fit? 
    • A. 

      Kwikset

    • B. 

      Chicago

    • C. 

      Weslock

    • D. 

      Weiser

  • 15. 
    A classroom function lock is designed so that:
    • A. 

      Students can lock themselves in the room

    • B. 

      The inside knob is locked at all times

    • C. 

      A key is required to exit

    • D. 

      A key is required to lock the room

  • 16. 
    The key shown above matches locks manufactured by: (Diagram not shown here) 
    • A. 

      Weslock

    • B. 

      Master

    • C. 

      Dexter

    • D. 

      Chicago

  • 17. 
    Pick guns work by: 
    • A. 

      Crushing the springs

    • B. 

      Bouncing the top pins above the shear line

    • C. 

      Clicking all pins above the shear line

    • D. 

      Bouncing the bottom pins above the shear line

  • 18. 
    What brand of lock does a M1 or 1092 key blank fit? 
    • A. 

      Matrix

    • B. 

      Weslock

    • C. 

      Master

    • D. 

      Schlage

  • 19. 
    What brand of lock does a WK2 or 1175 key blank fit? 
    • A. 

      Corbin

    • B. 

      Schlage

    • C. 

      Weslock

    • D. 

      Yale

  • 20. 
    A hotel function lockset is one that: 
    • A. 

      Locks and unlocks from the inside only

    • B. 

      Has visible occupancy indicators

    • C. 

      Requires a key or card from the outside in order to enter

    • D. 

      Can be left unlock

  • 21. 
    Which tools are used to manipulate a lock? 
    • A. 

      Tension wrench and power drill

    • B. 

      Phillips screwdriver and hook pick

    • C. 

      Power drill and drill bits

    • D. 

      Tension wrench and hook pick

  • 22. 
    When removing a Kwikset entrance set, what should the locksmith remove first? 
    • A. 

      Cylinder

    • B. 

      Strike

    • C. 

      Screws on the inside of the knob

    • D. 

      Latch

  • 23. 
    Difficulty inserting or removing the key blank during impressioning is caused by: 
    • A. 

      Improper lubricating the lock

    • B. 

      Applying too much turning force

    • C. 

      Turning the key in the wrong direction

    • D. 

      Improper filing the key

  • 24. 
    Of the following materials, which key blank produces the most obvious marks? 
    • A. 

      Nickel silver

    • B. 

      Brass

    • C. 

      Cobalt

    • D. 

      Steel

  • 25. 
    A power tool has a 3-pronged plug but the only available outlets are 2-pronged. What should the technician do?
    • A. 

      Remove the outlet and plug and hardwire the tool

    • B. 

      Use a 3-prong to 2-prong adapter

    • C. 

      Remove the ground prong from the power cord of the tool

    • D. 

      Locate a 3-pronged outlet

Related Topics

Back to Top Back to top
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.