Are You An FSG Expert? Find Out With This Quiz!

Reviewed by Editorial Team
The ProProfs editorial team is comprised of experienced subject matter experts. They've collectively created over 10,000 quizzes and lessons, serving over 100 million users. Our team includes in-house content moderators and subject matter experts, as well as a global network of rigorously trained contributors. All adhere to our comprehensive editorial guidelines, ensuring the delivery of high-quality content.
Learn about Our Editorial Process
| By Prvmarketing2014
P
Prvmarketing2014
Community Contributor
Quizzes Created: 18 | Total Attempts: 3,843
| Attempts: 182
SettingsSettings
Please wait...
  • 1/10 Questions

    If the camera used for videography, weighs more than .25 Kg then it must be secured by minimum of ______ points on different sides of Camera

    • 2
    • 3
    • 1
    • None
Please wait...
About This Quiz

Test your knowledge on FSG safety regulations with this engaging quiz! Discover if you're an expert in ensuring safety through proper design and installation of vehicle components like wing edges, belt drives, and camera mounts. A must for engineering enthusiasts and professionals in automotive safety.

Automotive Safety Quizzes & Trivia

Quiz Preview

  • 2. 

    Which of the following modification is not allowed after the tech inspection is over?

    • Replenishment of fluids

    • Recharging low voltage batteries

    • Replacement of worn tire

    • Replacement of brake caliper

    Correct Answer
    A. Replacement of brake caliper
    Explanation
    After the tech inspection is over, the modification that is not allowed is the replacement of brake caliper. This is because the tech inspection is conducted to ensure that the vehicle meets the required standards and any modifications made after the inspection can potentially compromise the safety and performance of the vehicle. The replacement of brake caliper involves a significant change in the braking system, which is a critical component for the safe operation of the vehicle. Therefore, it is not allowed to be modified after the tech inspection is completed.

    Rate this question:

  • 3. 

    All forward facing edges on the body work that will impact people, must have forward facing radii of atlest ____?

    • 1.5 inches

    • 2 inches

    • 3.5 inches

    • 4 inches

    Correct Answer
    A. 1.5 inches
    Explanation
    Forward facing edges on the body work that will impact people must have forward facing radii of at least 1.5 inches. This means that any edges on the body work that are likely to come into contact with individuals should have a minimum radius of 1.5 inches to reduce the risk of injury or harm. A larger radius helps to distribute the force of impact over a larger area, minimizing the potential for cuts, bruises, or other injuries.

    Rate this question:

  • 4. 

    What is the minimum distance of throttle cable from any exhust system?

    • 55.8 mm

    • 20.5mm

    • 50.8mm

    • 44mm

    Correct Answer
    A. 50.8mm
    Explanation
    The minimum distance of the throttle cable from any exhaust system is 50.8mm. This distance is necessary to prevent the throttle cable from getting damaged or melted due to the heat generated by the exhaust system. Keeping the cable at a safe distance ensures proper functioning of the throttle and avoids any potential hazards.

    Rate this question:

  • 5. 

    If the octane rating of a fuel is 91 and the RON for the same is 95, what is the value of MON for the same fuel.

    • 89

    • 87

    • 98

    • 46

    Correct Answer
    A. 87
    Explanation
    The MON (Motor Octane Number) is a measure of a fuel's resistance to knocking or pinging during the combustion process. It is typically lower than the RON (Research Octane Number). In this case, the octane rating of the fuel is 91, and the RON is 95. Since the MON is usually lower than the RON, the value of MON for the same fuel would be 87.

    Rate this question:

  • 6. 

    Non-metallic belt drive scatter shield for belts made of aluminum alloy 6061-T6 must be made from _____ thick and minimum width of equals _____ times the width of the belt

    • 3.0 mm, 1.7

    • 1.7mm, 3.0

    • 2.66 mm, 3

    • .105 inch, 1.7

    Correct Answer
    A. 3.0 mm, 1.7
    Explanation
    The non-metallic belt drive scatter shield for belts made of aluminum alloy 6061-T6 must be made from a thickness of 3.0 mm and have a minimum width that is 1.7 times the width of the belt.

    Rate this question:

  • 7. 

    If car underweight by 6.1 Kg after the event, what is the point penalty?

    • -20

    • -30

    • -40

    • -50

    Correct Answer
    A. -40
    Explanation
    If the car is underweight by 6.1 kg after the event, it means that the car is below the required weight limit. This indicates a violation of the rules or regulations set for the event. The point penalty is likely to be imposed as a consequence of this violation. The correct answer, -40, suggests that a penalty of 40 points will be deducted from the car's score due to the underweight issue.

    Rate this question:

  • 8. 

    For the monocoque construction, all equivalency calculation must prove equivalency relative to _____?

    • SAE/AISI 3025

    • SAE/AISI 1115

    • SAE/AISI 1025

    • SAE/AISI 1010

    Correct Answer
    A. SAE/AISI 1010
    Explanation
    For monocoque construction, all equivalency calculations must prove equivalency relative to SAE/AISI 1010. This means that any other material being considered for the construction must be proven to have the same strength, durability, and performance as SAE/AISI 1010. This ensures that the monocoque structure will be able to withstand the required loads and stresses without compromising safety or structural integrity.

    Rate this question:

  • 9. 

    All wing edges including wings, end plates, gurney flaps, wicker bills and undertray that could contact a pedstrain must have a minimum radius of ______

    • 15 mm

    • .060 inch

    • .60 inch

    • 2.5 mm

    Correct Answer
    A. .060 inch
    Explanation
    The correct answer is .060 inch. This is because all wing edges that could potentially come in contact with a pedestrian need to have a minimum radius of .060 inch. This radius helps to minimize the potential for injury in case of contact with the wing edges.

    Rate this question:

  • 10. 

    What is the minimum length and outer diameter of jack point?

    • 12inches and 30mm

    • 250mm and 30mm

    • 12 inches and 25mm

    • 300mm and 35mm

    Correct Answer
    A. 250mm and 30mm
    Explanation
    The minimum length and outer diameter of the jack point is 250mm and 30mm respectively.

    Rate this question:

Quiz Review Timeline (Updated): Mar 21, 2023 +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Mar 21, 2023
    Quiz Edited by
    ProProfs Editorial Team
  • Jan 11, 2014
    Quiz Created by
    Prvmarketing2014
Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.