OBS GMM Knowledge Check - Safety & Quality Training

1. Which of the following is an environmental factor:

Lack of attention

Complacency

Severe weather conditions

Lack of training

GMM Ref. 8.3.2

Explanation

GMM Ref. 8.3.2

2. When installing any IFE part, ensure it is serviceable and correct part as defined by AMM/IPC part. If it isn't, notify your immediate supervisor.

True

False

GMM Ref.6.7.2 (e)

Explanation

GMM Ref.6.7.2 (e)

3. In accordance with OBS GMM the maximum calibration intervals is:

18 months

There is no maximum intervals

12 months

6 months

GMM Ref.9.9.2.5

Explanation

GMM Ref.9.9.2.5

4. Which of the following statements is incorrect:

The Safety Net is a safety measure LMT uses to ensure that work is done properly and accurately.

LMT is required to use the applicable safety net when performing their assigned task.

A safety net consists of several steps for the employee to follow and implement when performing work on IFE System.

The safety net is only intended to be used with specific task only and does not apply for all tasks.

GMM Ref. 8.9.5.1/8.9.5.2

Explanation

GMM Ref. 8.9.5.1/8.9.5.2

5. Please complete the sentence below with the most appropriate answer.When performing work on the IFE system you must..

Be qualified and authorized to perform the task in accordance with this GMM.

Comply with OBS Uniform requirement.

Have fire extinguisher standing by.

Comply with PPE requirements.

GMM Ref. 8.8.3.3(a)

Explanation

GMM Ref. 8.8.3.3(a)

6. GMM Policies and procedures ,in some cases may override the requirements of complying with the regulations published by CAA (e.g. FAA, EASA, DGAC) under which certain OBS line stations are certified.

True

False

GMM Ref. 1.4.7

Explanation

GMM Ref. 1.4.7

7. Signoff for work performed, initiating and clearing defects, must be done in accordance with customer's procedures and request.

True

False

GMM Ref. 6.2.14

Explanation

GMM Ref. 6.2.14

8. OBS GMM states that you must always use calibrated tool whether it is station's tool or your personal tool.

True

False

GMM Ref. 9.9.2.9

Explanation

GMM Ref. 9.9.2.9

9. CATD stands for:

Current accepted technical data

Current approved technical document

Current approved technical data

Current accepted training document

CATD stands for "Current approved technical data." This acronym refers to technical information or documentation that has been reviewed and authorized for use in a particular context. It indicates that the information has undergone a process of approval and is currently valid and accepted as accurate and reliable. The other options, such as "Current accepted technical data," "Current approved technical document," and "Current accepted training document," do not accurately represent the meaning of the acronym CATD.

Explanation

CATD stands for "Current approved technical data." This acronym refers to technical information or documentation that has been reviewed and authorized for use in a particular context. It indicates that the information has undergone a process of approval and is currently valid and accepted as accurate and reliable. The other options, such as "Current accepted technical data," "Current approved technical document," and "Current accepted training document," do not accurately represent the meaning of the acronym CATD.

10. Which statement best describes "corrective action" in accordance with the GMM:

An action taken to eliminate the cause of a detected nonconformity or other undesirable condition to prevent its reoccurrence.

An immediate action taken to eliminate the cause of a detected nonconformity or other undesirable condition.

An action taken to address nonconformity or other undesirable condition to prevent its reoccurrence.

An action taken to address nonconformity or other undesirable condition to prevent.

1.2. Definitions:
Corrective Action
Action taken to eliminate the cause of a detected nonconformity or other undesirable condition to prevent its reoccurrence.

Explanation

1.2. Definitions:
Corrective Action
Action taken to eliminate the cause of a detected nonconformity or other undesirable condition to prevent its reoccurrence.

11. Which of the following is NOT a DP:

LMM

LMS

AM

MTL

1.2. Definitions:
Designated Person
Designated person referenced in this manual means any one or combination of the following personnel: HATS, AM, Director, LMM, LMS, DM, DLM as applicable to location, event and task.

Explanation

1.2. Definitions:
Designated Person
Designated person referenced in this manual means any one or combination of the following personnel: HATS, AM, Director, LMM, LMS, DM, DLM as applicable to location, event and task.

12. The GMM provides all of the following except:

Standards, policies and procedures and instructions.

Quality System.

Thales IFE parts management.

Maintenance instructions for performing work on IFE system on installed board aircraft.

The GMM (General Maintenance Manual) is a comprehensive document that provides guidelines, standards, policies, and procedures for maintaining and servicing various systems on an aircraft. It also includes instructions for performing maintenance work and managing parts. However, it does not specifically provide maintenance instructions for performing work on the In-Flight Entertainment (IFE) system on installed board aircraft. These instructions would typically be found in a separate manual or document specific to the IFE system.

Explanation

The GMM (General Maintenance Manual) is a comprehensive document that provides guidelines, standards, policies, and procedures for maintaining and servicing various systems on an aircraft. It also includes instructions for performing maintenance work and managing parts. However, it does not specifically provide maintenance instructions for performing work on the In-Flight Entertainment (IFE) system on installed board aircraft. These instructions would typically be found in a separate manual or document specific to the IFE system.

13. ATS Personnel are required to conform to all standards listed and identified in the GMM as applicable to their duties and responsibilities.

True

False

The statement is true because ATS (Air Traffic Services) Personnel are expected to adhere to all the standards mentioned in the GMM (General Maintenance Manual) that are relevant to their specific roles and responsibilities. This ensures that they perform their duties in accordance with the established guidelines and procedures, promoting safety and efficiency in air traffic control operations.

Explanation

The statement is true because ATS (Air Traffic Services) Personnel are expected to adhere to all the standards mentioned in the GMM (General Maintenance Manual) that are relevant to their specific roles and responsibilities. This ensures that they perform their duties in accordance with the established guidelines and procedures, promoting safety and efficiency in air traffic control operations.

14. Which of the following is a part of the safety net for the IFE work:

Refer to CATD.

Pay attention to details.

Check your work after completion.

All of the above.

SafetyNet for the IFE work:
Refer to current approved tech-data. CATD
Comply with applicable CAA regulations.
Pay attention to details.
Comply with tool Accountability.
Check your work after completion.
Qualified to perform task assigned.
Used approved materials.
Use correct part number.
Wear the proper authorized Thales uniform.

Explanation

SafetyNet for the IFE work:
Refer to current approved tech-data. CATD
Comply with applicable CAA regulations.
Pay attention to details.
Comply with tool Accountability.
Check your work after completion.
Qualified to perform task assigned.
Used approved materials.
Use correct part number.
Wear the proper authorized Thales uniform.

15. It is recommended that LMT performing any work on IFE system, installed on board of customer's aircraft, to apply tool accountability procedures.

True

False

It is recommended for LMT (Licensed Maintenance Technician) to apply tool accountability procedures when performing any work on the IFE (In-Flight Entertainment) system installed on the customer's aircraft. This means that the technician should keep track of the tools used during the work to ensure that they are properly accounted for and not left behind or misplaced. This helps to maintain the safety and integrity of the aircraft's systems and ensures that all tools are returned and accounted for after the work is completed.

Explanation

It is recommended for LMT (Licensed Maintenance Technician) to apply tool accountability procedures when performing any work on the IFE (In-Flight Entertainment) system installed on the customer's aircraft. This means that the technician should keep track of the tools used during the work to ensure that they are properly accounted for and not left behind or misplaced. This helps to maintain the safety and integrity of the aircraft's systems and ensures that all tools are returned and accounted for after the work is completed.

16. Signing for work performed on ATS documents means that LMT, select all applicable:

Is qualified and authorized, per the GMM, to perform the work.

Used the appropriate maintenance documentations to do the work.

Used the correct and approved parts/materials (where applicable)

None of the above

The correct answer is a combination of all three options. Signing for work performed on ATS documents indicates that the individual is qualified and authorized, as per the GMM, to carry out the work. It also confirms that they have used the appropriate maintenance documentations to complete the task and have utilized the correct and approved parts/materials, if applicable. This ensures that the work is done by a qualified person, following the necessary procedures, and using the correct resources.

Explanation

The correct answer is a combination of all three options. Signing for work performed on ATS documents indicates that the individual is qualified and authorized, as per the GMM, to carry out the work. It also confirms that they have used the appropriate maintenance documentations to complete the task and have utilized the correct and approved parts/materials, if applicable. This ensures that the work is done by a qualified person, following the necessary procedures, and using the correct resources.

Submit

17. ATS standards help improve performance, drive greater efficiency and enhance customer satisfaction and loyalty.

True

False

ATS standards, which stands for Applicant Tracking System standards, are guidelines and best practices that organizations follow to streamline their recruitment and hiring processes. By adhering to these standards, companies can improve their performance by ensuring a fair and efficient selection process. This leads to greater efficiency in hiring, as ATS systems automate many aspects of recruitment, such as resume screening and candidate tracking. Ultimately, by implementing ATS standards, organizations can enhance customer satisfaction and loyalty by making the hiring process smoother and more effective.

Explanation

ATS standards, which stands for Applicant Tracking System standards, are guidelines and best practices that organizations follow to streamline their recruitment and hiring processes. By adhering to these standards, companies can improve their performance by ensuring a fair and efficient selection process. This leads to greater efficiency in hiring, as ATS systems automate many aspects of recruitment, such as resume screening and candidate tracking. Ultimately, by implementing ATS standards, organizations can enhance customer satisfaction and loyalty by making the hiring process smoother and more effective.

Obs Gmm Knowledge Check - Safety & Quality Training