HVAC Sheet Metal Shop Quiz! Trivia

10 Questions | By Scottvincen | Last updated: Aug 14, 2020 | Total Attempts: 3757

Questions

Settings

HVAC sheet metal shop quiz trivia! Heating, ventilation, and air conditioning is something to take into account when it comes to building. The same goes without saying when it comes to choosing specific metals to work with. In this quiz, you will be tested on what happens in a metal shop. Do you think you know enough to pass all the questions? Do give them a try and see how well you do!

Questions and Answers

1.

___________ are used to safely carry mutiple sheets of sheet metal.
- A.
  
  Calipers
- B.
  
  Men
- C.
  
  Arms
- D.
  
  Hooks
2.

A Pittsburgh edge allows fabricated metal to be _________ together.
- A.
  
  Hung
- B.
  
  Snapped
- C.
  
  Bent
- D.
  
  Stood up
3.

__________ folded on the ends of duct work allow you to connect them together.
- A.
  
  Folds
- B.
  
  Cleats
- C.
  
  Ballasts
- D.
  
  Screws
4.

_____________, typically 8" long are used to hold ductwork together.
- A.
  
  Nails
- B.
  
  Pins
- C.
  
  Drives
- D.
  
  Mortars
5.

The ____________ connects the air handler or furnace to the ductwork on the supply side.
- A.
  
  Hood
- B.
  
  Topper
- C.
  
  Screws
- D.
  
  Plenum
6.

Carrying a section of 8" Rail on your service truck will allow you to do what in the field?
- A.
  
  Use it as a tool tray.
- B.
  
  Fabricate reducers/transitions in the field.
- C.
  
  Keep screws separated.
- D.
  
  Keep equipment on the shelves of the vehicle.
7.

A hand notcher is used for what?
- A.
  
  Allows space for clean bends in metal.
- B.
  
  Indicates where a bend should occur when laying out and marking.
- C.
  
  Hanging ductwork
- D.
  
  None of the above.
8.

A "bar fold" or "folding tool" has triangles stamped into them on each side. These triangles are used for what?
- A.
  
  Identifies the tool.
- B.
  
  Allows visualizing that the metal is completely inserted into the tool.
- C.
  
  Shows which end is up.
- D.
  
  None of the above
9.

A ________ __________ is used to initially layout a sheet metal project.
- A.
  
  Ink pen
- B.
  
  Hand punch
- C.
  
  Screw driver
- D.
  
  Wax pencil
10.

A ______________ is used to bend large sheets of metal.
- A.
  
  Bender
- B.
  
  Brake
- C.
  
  Machine
- D.
  
  Folder

Related Topics

More Hvac Quizzes

HVAC Journeyman Practice Test

Heating, ventilation, and air conditioning (HVAC) is a combination technology of indoor and vehicular environmental comfort. Are you training to be able to properly install and maintain such systems in any environment? The quiz...

Questions: 32 | Attempts: 27200 | Last updated: Sep 9, 2021

Sample Question
How many amps can a 40va, 120volt transformer with a 24volt secondary carry?

2.0

1.7

3.0

0.3

HVAC Quiz #1

This quiz is multiple choice and fill in the blank. It is worth 25 points. You can use your notes. Do not use capital letters or puncuation marks.

Questions: 12 | Attempts: 9629 | Last updated: Jul 15, 2020

Sample Question
VFD stands for what?

Very Fine Dog

Variable Air Volume

Variable Frequency Drive

Variable Frequency Motor

Heating And Air Conditioning Quiz! Trivia Questions

See if you can answer the trivia questions in this heating and air conditioning quiz. Many buildings have installed air conditioning in their houses or equipment to regulate the amount of heat, especially during the cold season,...

Questions: 14 | Attempts: 4031 | Last updated: Sep 4, 2020