FSC Registration Quiz #5

1. Which certificate must the required driver's underclothing have to have, to be permitted at FSG?

SFI 3.3 or FIA 8856-2000

FIA Standard 1986

SFI 3.3

SFI 3.2

The required driver's underclothing must have either an SFI 3.3 or FIA 8856-2000 certificate to be permitted at FSG.

Explanation

The required driver's underclothing must have either an SFI 3.3 or FIA 8856-2000 certificate to be permitted at FSG.

2. To prevent fuel and other liquids from pooling in closed structures of your car, it has to feature:

A single drain hole, with no specific size

2 drain holes, at least 25mm in diameter

A single drain hole, at least 30mm in diameter

2 drain holes, at least 25,4 mm in diameter

To prevent fuel and other liquids from pooling in closed structures of a car, it is necessary for the car to have 2 drain holes, each with a diameter of at least 25mm. These drain holes allow any liquids that may enter the closed structures to drain out, preventing pooling and potential damage to the car. Having two drain holes ensures that there is redundancy in case one drain hole becomes blocked or ineffective. The specific diameter of 25mm ensures that the drain holes are large enough to allow for efficient drainage of liquids.

Explanation

To prevent fuel and other liquids from pooling in closed structures of a car, it is necessary for the car to have 2 drain holes, each with a diameter of at least 25mm. These drain holes allow any liquids that may enter the closed structures to drain out, preventing pooling and potential damage to the car. Having two drain holes ensures that there is redundancy in case one drain hole becomes blocked or ineffective. The specific diameter of 25mm ensures that the drain holes are large enough to allow for efficient drainage of liquids.

3. Which reason for disqualification in the Endurance event is especially mentioned in the rules?

A malfunctioning brake light

Kicking more than 5 cones in a row

Tires with a very low grip level

An ugly driver

Low oil pressure in left corners

The correct answer is "A malfunctioning brake light." In the rules of the Endurance event, there is a specific mention of disqualification for a malfunctioning brake light. This suggests that having a properly functioning brake light is crucial for participating in the event, and any malfunction in this aspect can lead to disqualification.

Explanation

The correct answer is "A malfunctioning brake light." In the rules of the Endurance event, there is a specific mention of disqualification for a malfunctioning brake light. This suggests that having a properly functioning brake light is crucial for participating in the event, and any malfunction in this aspect can lead to disqualification.

4. How many combustion teams will be allowed to participate at FSG 2015?

75

65

25

115

75 combustion teams will be allowed to participate at FSG 2015.

Explanation

75 combustion teams will be allowed to participate at FSG 2015.

5. Which statement about requirements for camera mounts is wrong?

Helmet mounted cameras and helmet camera mounts are prohibited.

The mounts for video/photographic cameras must be of a safe and secure design.

All camera installations must be approved at Technical Inspection.

The camera mount must withstand a 20g impact in longitudinal direction. This must be proven in the SES.

The statement "The camera mount must withstand a 20g impact in longitudinal direction. This must be proven in the SES." is correct. The camera mount must be able to withstand a 20g impact in the longitudinal direction, which means it should be able to withstand a force equivalent to 20 times the force of gravity acting in the direction of motion. This requirement is necessary to ensure the safety and stability of the camera mount during use. It must be proven and tested in the SES (Safety Evaluation System) to ensure compliance with this requirement.

Explanation

The statement "The camera mount must withstand a 20g impact in longitudinal direction. This must be proven in the SES." is correct. The camera mount must be able to withstand a 20g impact in the longitudinal direction, which means it should be able to withstand a force equivalent to 20 times the force of gravity acting in the direction of motion. This requirement is necessary to ensure the safety and stability of the camera mount during use. It must be proven and tested in the SES (Safety Evaluation System) to ensure compliance with this requirement.

6. The fuel filler neck on your car is angled at 28 degrees from the vertical, the clear sight tube is installed parallely to the fuel filler neck. How long does it have to be?

141.57mm

110.39mm

84.95mm

66.22mm

The length of the clear sight tube needs to be 141.57mm because it is parallel to the angled fuel filler neck. This means that the length of the clear sight tube should be the same as the vertical height of the fuel filler neck.

Explanation

The length of the clear sight tube needs to be 141.57mm because it is parallel to the angled fuel filler neck. This means that the length of the clear sight tube should be the same as the vertical height of the fuel filler neck.

7. The baseline steel property for the Yield Strength (Sy) that is used for calculations of bending and buckling strength in an SES may not be lower
than:

180 MPa (26ksi)

200 GPa (29,000 ksi)

300 MPa (43.5 ksi)

305 MPa (44.2 ksi)

365 MPa (52.9 ksi)

The baseline steel property for the Yield Strength (Sy) used for calculations of bending and buckling strength in an SES must not be lower than 305 MPa (44.2 ksi). This means that the steel being used should have a minimum yield strength of 305 MPa in order to ensure the structural integrity and safety of the SES. Using a lower yield strength could result in a weaker structure that is more prone to bending and buckling under load, potentially leading to structural failure.

Explanation

The baseline steel property for the Yield Strength (Sy) used for calculations of bending and buckling strength in an SES must not be lower than 305 MPa (44.2 ksi). This means that the steel being used should have a minimum yield strength of 305 MPa in order to ensure the structural integrity and safety of the SES. Using a lower yield strength could result in a weaker structure that is more prone to bending and buckling under load, potentially leading to structural failure.

8. Which of these measures is not used to dimension the cockpit internal cross section template?

75mm

350mm

50mm

7mm

The measure of 75mm is not used to dimension the cockpit internal cross section template.

Explanation

The measure of 75mm is not used to dimension the cockpit internal cross section template.

9. Your motorcycle engine has a stroke of 42.5mm, at which rpm will the noise test be measured?

10.758 1/min

21.516 1/min

6500 1/min

Maximum engine rpm

Idle rpm

The noise test for the motorcycle engine will be measured at 10.758 1/min. This is determined by the stroke of the engine, which is 42.5mm. The stroke refers to the distance the piston travels in the cylinder. The noise test is likely conducted at a specific engine speed, and in this case, it is measured at 10.758 1/min.

Explanation

The noise test for the motorcycle engine will be measured at 10.758 1/min. This is determined by the stroke of the engine, which is 42.5mm. The stroke refers to the distance the piston travels in the cylinder. The noise test is likely conducted at a specific engine speed, and in this case, it is measured at 10.758 1/min.

10. Your car is equipped with a front and rear DRS, it is being pushed from the pit to the dynamic area by 2 team members at the push-bar. What is a true statement?

Everything is okay.

Because of a rule violation you will be moved to the end of the Endurance Queue.

You get a 25 point penalty due to a rule violation.

You get a 10 point penalty due to a rule violation.

not-available-via-ai

Explanation

not-available-via-ai