Es&t019

19 Questions | Attempts: 242
Share
SettingsSettings
Please wait...
  • 1/19 Questions

    LOS stands for:

    • Loss of Skip
    • Loss of Signal
    • Line of Sight
    • Line of Signal
Please wait...
About This Quiz

This QUIZ is made or by product of my continuous research & study about Electronics Engineering to help the Electronics Engineer/Technician Aspirants in passing the Board Examinations.

Electronics Engineering Quizzes & Trivia

Quiz Preview

  • 2. 

    Another term for a single microwave link is a:

    • Section

    • Hop

    • Skip

    • Jump

    Correct Answer
    A. Hop
  • 3. 

    The microwave signal path should clear obstacles by at least:

    • 60% of the Faraday zone

    • 60% of the Fresnel zone

    • 60% of the height of the antenna tower

    • 60% of the highest obstacle height

    Correct Answer
    A. 60% of the Fresnel zone
  • 4. 

    Repeaters are used in a microwave system:

    • Backup

    • When distance exceeds line-of-sight

    • Regenerative type

    • Increase power

    Correct Answer
    A. When distance exceeds line-of-sight
  • 5. 

    Microwave repeaters can be:

    • IF type

    • Baseband type

    • Regenerative type

    • All of the above

    Correct Answer
    A. All of the above
  • 6. 

    Fading is caused by:

    • Multipath reception

    • Attenuation due to weather

    • Ducting

    • All of the above

    Correct Answer
    A. All of the above
  • 7. 

    The typical reliability of a microwave system is:

    • 90%

    • 99%

    • 99.9%

    • 99.99%

    Correct Answer
    A. 99.99%
  • 8. 

    Microwave systems use:

    • FM

    • SSB

    • QAM

    • All of the above

    Correct Answer
    A. All of the above
  • 9. 

    Satisfactory performance of an analog microwave system is defined as:

    • A carrier-to-noise ratio that exceeds a given value

    • An ERP level that exceeds a given value

    • An energy-per-hertz level that exceeds a given value

    • None of the above

    Correct Answer
    A. A carrier-to-noise ratio that exceeds a given value
  • 10. 

    The effects of fading due to multipath reception are often reduced using:

    • Diversity

    • Power

    • High-gain antennas

    • Frequency selector

    Correct Answer
    A. Diversity
  • 11. 

    A typical microwave system uses a transmitted power of about:

    • 2 watts

    • 20 watts

    • 200 watts

    • 10 watts

    Correct Answer
    A. 2 watts
  • 12. 

    Too much antenna gain causes:

    • A very narrow microwave beam

    • A very wide microwave beam

    • Excessive noise

    • High power consume

    Correct Answer
    A. A very narrow microwave beam
  • 13. 

    Satisfactory performance of a digital microwave system requires a:

    • Low level of transmitted power

    • High level of ERP

    • Good energy per bit per transmitted Watt ratio

    • Good energy per bit per noise density ratio

    Correct Answer
    A. Good energy per bit per noise density ratio
  • 14. 

    LMDS stands for:

    • Local Microwave Distribution System

    • Local Multipoint Distribution System

    • Local Multichannel Distribution System

    • Local Multichannel Distribution System

    Correct Answer
    A. Local Multipoint Distribution System
  • 15. 

    LMDS is:

    • Bidirectional

    • Unidirectional

    • Multidirectional

    • Omnidirectional

    Correct Answer
    A. Bidirectional
  • 16. 

    In digital microwave systems, additional repeaters increase the

    • Reliability

    • Noise level

    • Jitter

    • Power

    Correct Answer
    A. Jitter
  • 17. 

    MMDS stands for:

    • Multichannel Microwave Distribution System

    • Multipoint Microwave Distribution System

    • Multichannel Multipoint Distribution System

    • Multiple Microwave Distribution Systems

    Correct Answer
    A. Multichannel Multipoint Distribution System
  • 18. 

    In analog microwave systems, additional repeaters increase the:

    • Reliability

    • Noise level

    • Jitter

    • Power

    Correct Answer
    A. Noise level
  • 19. 

    An advantage of digital techniques over analog in a microwave system is:

    • Less bandwidth is required

    • Accumulation of noise is reduced

    • It requires less power

    • All of the above

    Correct Answer
    A. Accumulation of noise is reduced

Quiz Review Timeline (Updated): Sep 21, 2015 +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Sep 21, 2015
    Quiz Edited by
    ProProfs Editorial Team
  • Sep 20, 2012
    Quiz Created by
    Catherine Halcomb
Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.