Instrument Manufacture Quiz Questions!

Approved & Edited by ProProfs Editorial Team
The editorial team at ProProfs Quizzes consists of a select group of subject experts, trivia writers, and quiz masters who have authored over 10,000 quizzes taken by more than 100 million users. This team includes our in-house seasoned quiz moderators and subject matter experts. Our editorial experts, spread across the world, are rigorously trained using our comprehensive guidelines to ensure that you receive the highest quality quizzes.
Learn about Our Editorial Process
| By Geffreca
G
Geffreca
Community Contributor
Quizzes Created: 2 | Total Attempts: 999
Questions: 7 | Attempts: 256

SettingsSettingsSettings
Instrument Manufacture Quiz Questions! - Quiz

Take this quiz and test your knowledge on instrument manufacture. What are you waiting for let's start it now!


Questions and Answers
  • 1. 

    INSTRUMENT MARKING TAPE SHOULD BE WRAPPED APPROXIMATELY ______ AROUND THE INSTRUMENT

    • A.

      1 TO 1 1/2

    • B.

      1 1/2 TO 2

    • C.

      2 TO 2 1/2

    • D.

      2 1/2 TO 3

    Correct Answer
    A. 1 TO 1 1/2
    Explanation
    The correct answer is "1 TO 1 1/2". This means that the instrument marking tape should be wrapped approximately 1 to 1 1/2 times around the instrument. This ensures that the tape is securely attached to the instrument and provides clear visibility of the marking. Wrapping the tape too loosely may cause it to come off easily, while wrapping it too tightly may obstruct the view of the marking. Therefore, wrapping the tape 1 to 1 1/2 times strikes a balance between securing the tape and maintaining visibility.

    Rate this question:

  • 2. 

    WHICH OF THE FOLLOWING IS NOT AN ACCEPTABLE FORM OF INSTRUMENT MARKING

    • A.

      LASER-ETCHING

    • B.

      ACID-BASE ETCHING

    • C.

      ELECTRIC ETCHING (ENGRAVING)

    • D.

      HEAT-FUSED NYLON

    Correct Answer
    C. ELECTRIC ETCHING (ENGRAVING)
    Explanation
    Electric etching (engraving) is not an acceptable form of instrument marking because it can damage the instrument's surface and compromise its integrity. Laser-etching, acid-base etching, and heat-fused nylon are all acceptable methods of instrument marking as they provide clear and durable markings without causing any damage to the instrument.

    Rate this question:

  • 3. 

    THE PURPOSE OF A SUCTION STYLET IS TO

    • A.

      UNCLOG THE SUCTION DURING SURGERY

    • B.

      CLEAN THE SUCTION IN THE DECONTAMINATION AREA

    • C.

      FACILITATE THE STERILIZATION PROCESS

    • D.

      PROVIDE A MEASURING GUIDE FOR THE SURGEON

    Correct Answer
    A. UNCLOG THE SUCTION DURING SURGERY
    Explanation
    A suction styler is used during surgery to unclog the suction. During surgical procedures, there may be instances where blood, tissue, or other debris can clog the suction device. The suction styler is designed to remove these obstructions and ensure that the suction device continues to function properly. By unclogging the suction, the surgeon can maintain a clear surgical field and effectively remove fluids and debris from the patient's body.

    Rate this question:

  • 4. 

    KERRISON LAMINECTOMY RONGEURS SHOULD BE TESTED USING

    • A.

      TISSUE PAPER

    • B.

      A PLASTIC DOWEL ROD

    • C.

      RUBBER TESTING MATERIAL

    • D.

      AN INDEX CARD

    Correct Answer
    D. AN INDEX CARD
    Explanation
    The correct answer is an index card because it is a thin and flexible material that can be easily inserted between the blades of the Kerrison rongeur to test their sharpness. By gently sliding the index card between the blades, any resistance or difficulty in cutting the card indicates that the rongeurs need to be sharpened. This method is commonly used in surgical settings to ensure that the instruments are in optimal condition for use.

    Rate this question:

  • 5. 

    SCISSORS WITH TUNGSTEN CARBIDE CUTTING EDGES ARE USUALLY IDENTIFIED BY

    • A.

      BLACK HANDLES

    • B.

      SILVER HANDLES

    • C.

      GOLD HANDLES

    • D.

      THE LETTERS TC

    Correct Answer
    C. GOLD HANDLES
    Explanation
    Scissors with tungsten carbide cutting edges are usually identified by gold handles. This is because tungsten carbide is a very hard and durable material, and gold is often used to signify high quality and value. The gold handles serve as a visual indicator that the scissors have tungsten carbide cutting edges, which makes them more effective and long-lasting compared to scissors with other types of cutting edges.

    Rate this question:

Quiz Review Timeline +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Oct 16, 2024
    Quiz Edited by
    ProProfs Editorial Team
  • Mar 15, 2012
    Quiz Created by
    Geffreca
Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.