2A652 CDC Volume 1 Test: Practice Questions On Aerospace Ground Equipment!
-
Pliers are properly used to
-
Loosen a nut
-
Hold material
-
Replace a wrench
-
Hammer a cotter pin
-
If you are planning on being part of the aerospace ground equipment personnel, you will be responsible for providing and maintaining essential maintenance support capabilities to maintain or repair the aircraft. Below is a 2A652 CDC Volume 1 test about the aerospace ground equipment! Give it a try and see just how much you have understood so far. All the See morebest!
(196).jpg "2A652 CDC Volume 1 Test: Practice Questions On Aerospace Ground Equipment! - Quiz")
Quiz Preview
- 2.
Which pliers have a locking device to hold materials securely?
-
Dikes
-
Vice Grip
-
Snap ring
-
Water pump
Correct Answer
A. Vice GripExplanation
Vice Grip pliers have a locking device that allows them to securely hold materials in place. This locking mechanism can be adjusted to clamp down tightly on the object being worked on, providing a secure grip and preventing it from slipping or moving. This feature makes Vice Grip pliers particularly useful in situations where a strong and secure hold is required, such as in construction or automotive work.Rate this question:
-
- 3.
Before removing a component from an air compressor for safety you must ensure
-
The air compressor is grounded
-
The air strainer is in place
-
The battery is disconnected
-
All air pressure is drained
Correct Answer
A. All air pressure is drainedExplanation
Before removing a component from an air compressor for safety, it is important to ensure that all air pressure is drained. This is necessary to prevent any accidental release of pressurized air, which can cause serious injuries or damage. By draining the air pressure, the risk of sudden release of compressed air is eliminated, making it safer to work on the air compressor.Rate this question:
-
- 4.
Diagonal cutting pliers are designed to cut
-
Bolts
-
Rivets
-
Small wire
-
Hard steel
Correct Answer
A. Small wireExplanation
Diagonal cutting pliers are designed to cut small wire because they have a sharp cutting edge that is angled to allow for easy access to the wire. The design of the pliers allows for a clean and precise cut, making them ideal for cutting small wires in various applications such as electrical work, crafting, and jewelry making. The pliers' cutting ability is not suited for cutting bolts, rivets, or hard steel, as these materials require more specialized tools with greater cutting force.Rate this question:
-
- 5.
If you must push a wrench rather than pull it, how should you do it?
-
Grasp the handle near the socket
-
Grip the wrench tightly near the center
-
Grip the wrench tightly with both hands
-
Use the base of your palm and hold your hand open
Correct Answer
A. Use the base of your palm and hold your hand openExplanation
To push a wrench instead of pulling it, it is recommended to use the base of your palm and hold your hand open. This technique allows for better control and stability while applying force in a forward direction. Gripping the wrench tightly near the center or with both hands may not provide the same level of precision and control. Grasping the handle near the socket is not mentioned as a suitable method for pushing the wrench.Rate this question:
-
- 6.
The symbol that represents the most serious maintenance condition is a
-
Red X
-
Red dash
-
Red diagonal
-
Circled red X
Correct Answer
A. Red XExplanation
The symbol that represents the most serious maintenance condition is a red X. This symbol typically indicates a critical issue or failure that requires immediate attention and should not be ignored. The red X serves as a clear visual warning to alert individuals to the severity of the maintenance condition and the need for prompt action to address the problem.Rate this question:
-
- 7.
What marking is applied to Aerospace Ground Equipment (AGE) for night safety?
-
Safety/danger
-
Informational
-
Caution/warning
-
Reflectorization
Correct Answer
A. ReflectorizationExplanation
Reflectorization is the marking applied to Aerospace Ground Equipment (AGE) for night safety. This involves the use of reflective materials or coatings on the equipment to enhance visibility in low light conditions. By reflecting light, these markings make the equipment more visible to operators, reducing the risk of accidents and ensuring safety during nighttime operations.Rate this question:
-
- 8.
Which type of screrwdriver is used in tight places when there isn't enough room to use a standard screwdriver?
-
Cross-point
-
Flat-blade
-
Phillips
-
Offset
Correct Answer
A. OffsetExplanation
An offset screwdriver is used in tight places when there isn't enough room to use a standard screwdriver. The offset design allows the handle to be at an angle to the shaft, enabling the user to reach screws that are located in narrow or confined spaces where a straight screwdriver cannot fit. This makes the offset screwdriver a practical tool for working in tight corners or areas with limited access.Rate this question:
-
- 9.
What portion of the bolt identifies the type and material of the bolt?
-
nut
-
Grip
-
Head
-
Shank
Correct Answer
A. HeadExplanation
The head of a bolt typically contains markings or symbols that indicate the type and material of the bolt. These markings can include information such as the bolt grade, manufacturer's symbol, or material specifications. Therefore, the head is the portion of the bolt that identifies the type and material of the bolt.Rate this question:
-
- 10.
What is the primary focus of the entire maintenance process?
-
Preventive
-
Corrective
-
Inductive
-
Conductive
Correct Answer
A. PreventiveExplanation
The primary focus of the entire maintenance process is preventive. This means that the main goal is to prevent problems or breakdowns from occurring in the first place. This can be achieved through regular inspections, routine maintenance tasks, and proactive measures to identify and address potential issues before they become major problems. By taking a preventive approach, organizations can minimize downtime, reduce repair costs, and ensure that equipment and systems are functioning optimally.Rate this question:
-
- 11.
Why should you apply silicone sealant to the valve stem area of a wheel?
-
To keep rims from flying apart
-
To keep water from entering rims
-
As a treatment for weather cracks
-
As a treatment for severe corrosion
Correct Answer
A. To keep water from entering rimsExplanation
Applying silicone sealant to the valve stem area of a wheel helps to keep water from entering the rims. Water entering the rims can cause corrosion and damage to the wheel, reducing its lifespan and potentially leading to further issues. By sealing the valve stem area with silicone, it provides a barrier that prevents water from seeping into the rims, protecting them from potential damage.Rate this question:
-
- 12.
The primary cause of Foreign Object Damage (FOD) is
-
Aircraft
-
Nature
-
People
-
AGE
Correct Answer
A. PeopleExplanation
The primary cause of Foreign Object Damage (FOD) is people. This refers to any debris or objects left on or near the aircraft by maintenance personnel, ground crew, or passengers. It can include tools, parts, luggage, or even small rocks or debris that can be sucked into the engine during takeoff or landing. FOD can cause significant damage to the aircraft's engines, landing gear, or other critical components, leading to safety hazards and costly repairs. Therefore, it is crucial for everyone involved in aircraft operations to be vigilant and follow proper procedures to prevent FOD incidents.Rate this question:
-
- 13.
Which of these is the best example of supply conservation?
-
Not keeping commonly used supplies on hand
-
Ordering twice the supplies needed to do a job
-
Ordering the minimum supplies necessary to do a job
-
Replacing all hardware on equipment at every inspection
Correct Answer
A. Ordering the minimum supplies necessary to do a jobExplanation
Ordering the minimum supplies necessary to do a job is the best example of supply conservation because it ensures that only the required amount of supplies are being used, minimizing waste and reducing unnecessary expenses. This approach promotes efficiency and resourcefulness by avoiding excessive ordering and stockpiling of supplies.Rate this question:
-
- 14.
What should you do if your vehicle meets a moving aircraft at night?
-
Turn off your headlights and leave your parking lights on
-
Dim your headlights and continue on
-
Stop and change directions
-
Turn all lights off
Correct Answer
A. Turn off your headlights and leave your parking lights onExplanation
When your vehicle meets a moving aircraft at night, it is important to turn off your headlights to avoid blinding the pilot. However, you should leave your parking lights on to ensure that your vehicle is still visible to others on the road. This will help maintain safety and prevent any accidents or confusion between the aircraft and your vehicle.Rate this question:
-
- 15.
Periodic inspection workcards are divided into three sections that cover the requirements for
-
Periodic inspection, lubrication, and special inspection
-
Periodic inspection, special inspection, and safety
-
Periodic inspection, lubrication, and safety
-
Special inspection, lubrication, and safety
Correct Answer
A. Periodic inspection, lubrication, and special inspectionExplanation
Periodic inspection workcards are divided into three sections that cover the requirements for periodic inspection, lubrication, and special inspection. This means that the workcards provide instructions and guidelines for conducting periodic inspections, ensuring proper lubrication of equipment, and performing any necessary special inspections. These three sections cover the essential aspects of maintaining and ensuring the safety and proper functioning of the equipment being inspected.Rate this question:
-
- 16.
Which section of the Air Force Technical Order (AFTO) Form 244 is used to record a forms review?
-
Part V, maintenance/delayed discrepancy
-
Part II, non-scheduled inspection
-
Part III, scheduled inspection
-
Part IV, supervisory review
Correct Answer
A. Part IV, supervisory reviewExplanation
The correct answer is Part IV, supervisory review. In the Air Force Technical Order (AFTO) Form 244, Part IV is used to record the supervisory review. This section is where the supervisor or higher-ranking personnel review the form and ensure that all necessary information is filled out correctly and completely. It is an important step in the process to ensure accuracy and compliance with regulations.Rate this question:
-
- 17.
Which of these items must be removed from test equipment before storage?
-
Wet and dry cell batteries
-
Dry charge batteries
-
Battery compartment
-
Battery holder
Correct Answer
A. Wet and dry cell batteriesExplanation
Wet and dry cell batteries must be removed from test equipment before storage because they can leak or corrode over time, causing damage to the equipment. Removing the batteries ensures that the equipment remains in good condition and prevents any potential hazards.Rate this question:
-
- 18.
Replacement hardware decisions are based on
-
Supervisor's preference
-
Serviceability criteria
-
Availability
-
Cost
Correct Answer
A. Serviceability criteriaExplanation
Replacement hardware decisions are based on serviceability criteria. This means that when deciding to replace hardware, factors such as the ease of maintenance, repairability, and the availability of spare parts are taken into consideration. The goal is to ensure that the replacement hardware can be easily serviced and maintained, minimizing downtime and maximizing the lifespan of the hardware. This criterion is important as it ensures that the replacement hardware can be effectively managed and supported in the long run.Rate this question:
-
- 19.
The effect of noise depends on the
-
Deflection, frequency, and volume
-
Frequency, volume, and duration of exposure
-
Deflection, volume, and duration of exposure
-
Deflection, frequency, and duration of exposure
Correct Answer
A. Frequency, volume, and duration of exposureExplanation
The effect of noise depends on the frequency, volume, and duration of exposure. The frequency of the noise refers to how high or low the pitch of the sound is, and different frequencies can have different effects on the human body. The volume of the noise refers to the intensity or loudness of the sound, and higher volumes can cause more damage. The duration of exposure refers to how long a person is exposed to the noise, and longer durations can increase the risk of hearing damage. Therefore, all three factors - frequency, volume, and duration of exposure - play a role in determining the effect of noise.Rate this question:
-
- 20.
Two signatures are required to clear discrepancies that carry the maintenance symbol(s)
-
Red X only
-
Red dash only
-
Red X or red diagonal
-
Red dash or red diagonal
Correct Answer
A. Red X onlyExplanation
When there are discrepancies that carry the maintenance symbol(s), it is necessary to have two signatures to clear them. The correct symbol for this purpose is the red X. Therefore, the answer "red X only" is correct as it indicates that only the red X symbol is required to clear the discrepancies.Rate this question:
-
- 21.
When preparoing Aerospace Ground Equipment (AGE) for mobility, what two problem areas should you watch for?
-
Cleanliness and leaks
-
AFTO Forms 244s and 95s
-
Readiness and responsiveness
-
Flight kit inventories and personnel status
Correct Answer
A. Cleanliness and leaksExplanation
When preparing Aerospace Ground Equipment (AGE) for mobility, it is important to watch for cleanliness and leaks. Cleanliness is crucial to ensure that the equipment is free from dirt, debris, and any potential contaminants that could affect its performance or cause damage. Leaks, on the other hand, can indicate a problem with the equipment's fluid systems, such as fuel or hydraulic leaks, which need to be addressed before the equipment can be mobilized. Therefore, monitoring and addressing cleanliness and leaks are essential steps in preparing AGE for mobility.Rate this question:
-
- 22.
The size of the screwdriver is determined by the shank
-
Length
-
Weight
-
Temper
-
Width
Correct Answer
A. LengthExplanation
The size of a screwdriver is determined by its shank length. The shank refers to the part of the screwdriver that fits into the handle and extends to the tip. The length of the shank determines the reach and depth at which the screwdriver can be used effectively. A longer shank allows for reaching screws in deeper or hard-to-reach places, while a shorter shank is suitable for screws that are closer to the surface. Therefore, the length of the shank is a crucial factor in determining the size and functionality of a screwdriver.Rate this question:
-
- 23.
An example of a tecnical order (TO) deficiency is
-
Insufficient information
-
Improper page sequences
-
Typographical errors
-
Misspelled words
Correct Answer
A. Insufficient informationExplanation
A technical order (TO) deficiency refers to a situation where the provided information in the TO is not enough or lacking in detail. This means that the TO does not provide sufficient guidance or instructions for the task at hand, making it difficult for the user to understand or carry out the required procedure effectively. This can lead to confusion, errors, and potentially unsafe situations.Rate this question:
-
- 24.
What type of maintenance is performed in a repair shop on components removed from equipment?
-
Off-equipment
-
On-equipment
-
Preliminary
-
Corrective
Correct Answer
A. Off-equipmentExplanation
Off-equipment maintenance refers to the type of maintenance that is performed on components after they have been removed from the equipment. This maintenance is typically carried out in a repair shop or workshop, where the components can be thoroughly inspected, repaired, and tested before being reinstalled back into the equipment. It is important to perform off-equipment maintenance to ensure that the components are in optimal condition and will function properly when they are reinstalled.Rate this question:
-
- 25.
After depot has repaired an item, they send copies of the Air Force Technical Order (AFTO) Form 375, Selected Equipment Repair Cost Estimate, to whom?
-
MAJCOM
-
Originating unit
-
Inventory manager
-
All of the above
Correct Answer
A. All of the aboveExplanation
After the depot has repaired an item, they send copies of the Air Force Technical Order (AFTO) Form 375, Selected Equipment Repair Cost Estimate, to MAJCOM, originating unit, and inventory manager. This is because all these entities need to be informed about the repair cost estimate for the item. MAJCOM is responsible for overseeing the repair process, the originating unit needs to be aware of the cost for budgeting purposes, and the inventory manager needs to update the records and ensure accurate tracking of repair costs. Therefore, all of the above options receive copies of the AFTO Form 375.Rate this question:
-
- 26.
What type of washer is used to shim?
-
Spiral lock washers
-
Plain washers
-
Crush washers
-
Lock washers
Correct Answer
A. Plain washersExplanation
Plain washers are used to shim. Shimming is the process of inserting thin layers of material, such as washers, between two surfaces to adjust the alignment or fill gaps. Plain washers are flat, circular washers with a central hole. They provide a smooth and even surface for distributing the load and preventing damage to the surfaces being shimmed. Spiral lock washers, crush washers, and lock washers have different purposes and are not typically used for shimming.Rate this question:
-
- 27.
What type of index is used to order technical orders (TO)?
-
TO catalog
-
Alphabetical index
-
Cross-reference table
-
List of applicable publications
Correct Answer
A. TO catalogExplanation
A TO catalog is used to order technical orders (TO). It provides a comprehensive list of all available TOs, allowing users to easily locate and order the specific TO they need. This catalog serves as a centralized reference point for TOs, ensuring efficient management and accessibility of these documents. It is specifically designed to facilitate the ordering process for TOs, making it the most appropriate index type for this purpose.Rate this question:
-
- 28.
Which Inspection is recorded in Part II, Non-Scheduled Inspection, of the Air Force Technical Order (AFTO) Form 244?
-
Periodic
-
Operator
-
Service
-
Special
Correct Answer
A. ServiceExplanation
In the Air Force Technical Order (AFTO) Form 244, the inspections that are recorded in Part II, Non-Scheduled Inspection, are service inspections. These inspections are conducted to ensure that the aircraft is in proper working condition and meets all the necessary maintenance requirements. Service inspections are typically carried out at regular intervals to maintain the overall performance and safety of the aircraft.Rate this question:
-
- 29.
What is the condition of a component bearing a red tag?
-
Condemned
-
Reparable
-
Suspended
-
Serviceable
Correct Answer
A. CondemnedExplanation
A component bearing a red tag is in a condemned condition. This means that the component is deemed to be unsafe or unfit for use and should not be used or repaired. It may pose a risk to safety or may be irreparable due to significant damage or wear.Rate this question:
-
- 30.
While you're operating a battery charger, you notice that the ammeter reading was initially high, but has gradually decreased. Is it malfunctioning?
-
Yes. The charger is improperly connected.
-
Yes. Stop charging and troubleshoot
-
No. This is a normal condition
-
Yes. The voltage is set to high
Correct Answer
A. No. This is a normal condition -
- 31.
What is "After the fact reporting"?
-
Creating the narrative description of SRD codes
-
Requesting information on parts via stock number
-
Creating the job and immediately entering the corrective action
-
Requesting a detailed repair history for a specific piece of equipment
Correct Answer
A. Creating the job and immediately entering the corrective actionExplanation
After the fact reporting refers to the process of creating a job and immediately entering the corrective action. This means that when an issue or problem arises, a job is created and the necessary steps to address and fix the problem are immediately recorded. This allows for real-time documentation of the corrective action taken, ensuring that accurate and timely information is available for future reference and analysis.Rate this question:
-
- 32.
What Standard Base Supply System (SBSS) ordering priority is used for red "X" conditions?
-
03
-
04
-
05
-
06
Correct Answer
A. 03Explanation
The correct answer is 03. The Standard Base Supply System (SBSS) ordering priority used for red "X" conditions is 03. This means that red "X" conditions have the highest priority for ordering supplies. Red "X" conditions indicate that an aircraft or equipment is grounded due to a critical deficiency or malfunction. Therefore, it is crucial to prioritize the ordering of supplies to quickly resolve the issue and get the aircraft or equipment back in operation.Rate this question:
-
- 33.
Which part of the torque wrench scale is not normally used?
-
Lower 10 percent
-
Lower 20 percent
-
Upper 20 percent
-
Upper 10 percent
Correct Answer
A. Lower 20 percentExplanation
The lower 20 percent of the torque wrench scale is not normally used. This means that the torque values in the lower range of the scale are not frequently required or applied in most situations. The majority of torque applications typically fall within the middle to upper range of the scale, making the lower 20 percent less commonly utilized.Rate this question:
-
- 34.
What type of nut should never be used in areas where the temperature exceeds 250 degrees fahrenheit?
-
Self-locking nut
-
Castellated nuts
-
Metallic nuts
-
Plain nuts
Correct Answer
A. Self-locking nutExplanation
A self-locking nut should never be used in areas where the temperature exceeds 250 degrees Fahrenheit because it is designed with a nylon insert that provides resistance against loosening due to vibrations. However, at high temperatures, the nylon insert can melt or degrade, causing the nut to lose its locking ability and potentially lead to the fastener coming loose. Therefore, it is not suitable for use in high-temperature environments.Rate this question:
-
- 35.
A material deficiency exhibit tag can be identified by its
-
Brown color
-
Green color
-
White color
-
Yellow color
Correct Answer
A. Brown colorExplanation
A material deficiency exhibit tag can be identified by its brown color. This color is commonly used to indicate a material deficiency in various industries and contexts. The brown color stands out and helps to easily identify items that have been marked as deficient or in need of attention. It serves as a visual cue to draw attention to the specific item or material that requires further inspection or correction.Rate this question:
-
- 36.
When bech stock levels fall below 50 percent, you should
-
Post a due-out list
-
Place a red tag on the bin
-
Notify supply that stock level is low
-
Initial the initial supply stock listing
Correct Answer
A. Place a red tag on the binExplanation
When the stock levels fall below 50 percent, placing a red tag on the bin is the appropriate action to take. This is because a red tag serves as a visual indicator that the stock level is low and needs attention. It helps in identifying and prioritizing the bins that require immediate replenishment or restocking. This action allows for efficient inventory management and ensures that the low stock is promptly addressed.Rate this question:
-
- 37.
The size of a flat, cold chisel is determined by the
-
Length of the cutting edge
-
Width of the cutting edge
-
Length of the handle
-
Length of the chisel
Correct Answer
A. Width of the cutting edgeExplanation
The size of a flat, cold chisel is determined by the width of the cutting edge. The width of the cutting edge refers to the distance between the two sides of the chisel's blade. This measurement is important because it determines the amount of material that can be removed or cut through with each strike of the chisel. A wider cutting edge will be able to remove more material, while a narrower cutting edge will be more suitable for finer and more precise work. Therefore, the width of the cutting edge is a key factor in determining the size and functionality of a flat, cold chisel.Rate this question:
-
- 38.
Before operating the pneumatic impact wrench, you must
-
Inspect it
-
Lubricate it
-
Blow out the air hose
-
Ensure that its use is necessary
Correct Answer
A. Blow out the air hoseExplanation
Before operating the pneumatic impact wrench, it is necessary to blow out the air hose. This step ensures that any debris or moisture that may have accumulated in the hose is removed, preventing it from entering the wrench and potentially causing damage. By blowing out the air hose, the wrench can operate smoothly and efficiently, minimizing the risk of malfunctions or reduced performance.Rate this question:
-
- 39.
What color code is given to pre-insulated terminals that can be used to terminate wire sizes 18 through 22?
-
Red
-
Blue
-
Green
-
Yellow
Correct Answer
A. RedExplanation
Pre-insulated terminals are color-coded to indicate the wire size they can be used with. In this case, the color code red is given to pre-insulated terminals that can be used to terminate wire sizes 18 through 22. Therefore, the correct answer is red.Rate this question:
-
- 40.
Which time compliance technical orders (TCTO) has circled red Xs with alternately spaced red diagonals bordering the first page?
-
Urgent
-
Safety
-
Routine
-
Immediate
Correct Answer
A. UrgentExplanation
The TCTO with circled red Xs and alternately spaced red diagonals bordering the first page is classified as "Urgent." This indicates that the TCTO requires immediate attention and action due to the urgency of the situation. The red Xs and diagonals are likely used to visually highlight the importance and urgency of the TCTO.Rate this question:
-
- 41.
What is the most widely used status tag?
-
DD Form 1575, Suspended Tag
-
AFTO Form 1574, Serviceable Tag
-
AFTO Form 350, Reparable Processing Tag
-
DD Form 1577-2, Unserviceable (Reparable) Tag
Correct Answer
A. AFTO Form 350, Reparable Processing TagExplanation
AFTO Form 350, Reparable Processing Tag is the most widely used status tag because it is specifically designed for items that are in need of repair. This form allows for the efficient tracking and processing of items that are deemed reparable, ensuring that they are properly repaired and returned to service as quickly as possible. The other forms listed are also used for tracking the status of items, but they serve different purposes such as indicating items that are suspended, serviceable, or unserviceable.Rate this question:
-
- 42.
What Maintenance Data Documentation (MDD) code identifies the system that was worked?
-
Type maintenance code
-
Work unit code
-
Category labor
-
Units
Correct Answer
A. Work unit codeExplanation
The Maintenance Data Documentation (MDD) code that identifies the system that was worked is the work unit code. This code is used to specify the specific unit or component of a system that was worked on during maintenance activities. It helps in tracking and documenting the maintenance work performed on different units or components of a system.Rate this question:
-
- 43.
Preventive maintenance for corrosion includes
-
Cleaning, inspecting, and painting
-
Cleaning, inspecting, and marking
-
Inspecting, marking, and painting
-
Cleaning, marking, and painting
Correct Answer
A. Cleaning, inspecting, and paintingExplanation
Preventive maintenance for corrosion involves a three-step process: cleaning, inspecting, and painting. Cleaning helps remove any dirt or debris that may contribute to corrosion, while inspecting allows for the identification of any existing or potential corrosion. Finally, painting helps protect the surface from corrosion by creating a barrier between the metal and the environment. This combination of cleaning, inspecting, and painting ensures that corrosion is prevented or addressed in a proactive manner.Rate this question:
-
- 44.
What type of bolt is typically used to connect accessories to an engine?
-
Stud
-
Fine thread bolt
-
Coarse thread bolt
-
General purpose bolt
Correct Answer
A. StudExplanation
A stud is typically used to connect accessories to an engine. Unlike bolts, studs do not have a head and are threaded on both ends. One end is screwed into the engine block, while the other end is used to secure the accessory by tightening a nut onto it. Studs provide a more secure and stable connection, as they can withstand higher levels of torque and prevent the accessory from loosening or vibrating during operation.Rate this question:
-
- 45.
To be held responsible for property, you must
-
Possess it
-
Sign for it
-
Be a 5 level
-
Be a supervisor
Correct Answer
A. Possess itExplanation
In order to be held responsible for property, one must possess it. Possession implies having physical control or ownership of the property. Without possession, it would be difficult to establish a direct link between an individual and the property in question. Possession is often a key factor in determining liability and responsibility for any damages or losses associated with the property.Rate this question:
-
- 46.
Items for which accountability is dropped from all records when they are issued are considered
-
DIFM
-
Excess
-
Expendable
-
Nonexpendable
Correct Answer
A. ExpendableExplanation
Expendable items are those for which accountability is dropped from all records when they are issued. This means that once these items are issued, there is no need to track or keep records of them anymore. They are considered to be consumed or used up in the process, hence the term "expendable". This is in contrast to nonexpendable items, which still need to be accounted for even after they are issued.Rate this question:
-
- 47.
Which symbol indicates an operational check is overdue?
-
Red X
-
Red dash
-
Red diagonal
-
Circled red X
Correct Answer
A. Red dashExplanation
The red dash symbol indicates that an operational check is overdue. This symbol is commonly used to represent a task or action that has not been completed within the required timeframe. It serves as a visual reminder to address the overdue check and ensure that it is performed promptly.Rate this question:
-
- 48.
When entering Maintenance Data Documentation (MDD) what should be a short but accurate description of the problem?
-
How malfunction code
-
Action taken code
-
Corrective action
-
Discrepancy
Correct Answer
A. DiscrepancyExplanation
In Maintenance Data Documentation (MDD), a short but accurate description of the problem should be referred to as a "discrepancy". This term is commonly used to describe any deviation or inconsistency observed in the maintenance process or equipment. It helps in identifying and documenting the specific issue encountered, allowing for proper analysis and resolution.Rate this question:
-
- 49.
Which type of technical lorder (TO) is normally used only to maintain test or early production model equipment?
-
Prototype
-
Automation
-
Preliminary
-
Abbreviated
Correct Answer
A. PreliminaryExplanation
The type of technical order (TO) that is normally used only to maintain test or early production model equipment is the preliminary TO. This type of TO is typically used during the initial stages of equipment development or testing to provide maintenance instructions and procedures. It is often used before a finalized version of the TO, such as the abbreviated TO, is created for widespread use.Rate this question:
-
Quiz Review Timeline (Updated): Mar 22, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 22, 2023Quiz Edited by
ProProfs Editorial Team -
Oct 27, 2009Quiz Created by
Dinstaar