Axe Mantenimiento

The signaling of Line is sent through Channel 16 in R2 or associated channel.

IOIOP is the command used to request a list of the defined IOs in the IO table.

The given answer "MS" is correct because it represents the first step in the process of performing a manual dump using the SYBSUP command. "MS" stands for "Memory Start" which means that the information that needs to be stored in memory is first copied. This step is essential before the information can be backed up to the file device.

The correct answer is EMRP. This is because the given statement mentions that the card is for an LSM (P-86) and it stores regional software for conducting routine tests and echo tests. The letters in the answer option EMRP are a rearrangement of the letters in LSM (P-86), indicating that this is the correct combination.

Each EMG in Telmex is connected to the Group Selector (GSD) through 16 lines of PCM.

The correct answer is "Software, Reinico". The statement explains that the FORLOPP function is a standard function that includes the ability to recover an error with a "Reinico" (reboot) instead of a system shutdown. This suggests that the function is designed to handle software errors and initiate a reboot to resolve the issue.

The correct answer is SLCT. SLCT is the card that performs the different tests on the LIB cards.

When troubleshooting the EMG CONTROL DOWN failure, it is necessary to verify the states of the STR's (Signal Transfer Relays) and the numbers of the CLC's (Control Logic Cards). These components play a crucial role in the control system, and their states and numbers can provide important information about the cause of the failure. By checking these states and numbers, technicians can identify any issues or discrepancies that may be contributing to the EMG CONTROL DOWN failure.

The given answer "KR's" refers to the routes with devices used for receiving tones from keypad phones. The other options mentioned in the question, "BT's", "CSK's", and "E/R de Codigo", are not relevant to the given context and do not represent the routes used for receiving tones from keypad phones.

After a power outage, it is necessary to verify the units of the IOG. For the NA test, the NA-1 unit needs to be unlocked using the BLSUE command. The IMRDP command with TEST=2 parameters should be used. The opposite node to be tested should be blocked. The FAULT CODE=8 should be eliminated.

The correct answer is "EX-WORKING/NORMAL y SB-WORKING/NORAMAL". This means that the normal working state of a master node pair is when both the master node and the standby node are in working and normal states.

The correct answer is "Cambios Funcionales". The given statement suggests that this is one of the most important tasks of the CPS (presumably referring to a computer system) and can be used to add, replace, or remove functional blocks in the system. The other options mentioned, such as "Bitacora de Eventos" (Event Log), "Alteracion de Tamaño" (Size Alteration), and "Adminitracion de Carga" (Load Management), do not align with the given statement and are therefore not the correct answer.

The correct answer is 1. The question is asking about the MP used for testing voltage, insulation, phase angle, and capacitance. The MP stands for Measurement Point, which is a location in a system where measurements can be taken. Therefore, the correct answer is 1, as it is the MP used for these specific tests.

The given correct answer "BLCLI" is a command used for blocking a link. It is a short form for "Block Link Command Interface" which is a tool or interface used to block or disable a specific link in a network. This command is commonly used in networking and telecommunications systems to manage and control the flow of data through different links.

The given answer states that the parameter IOREDEP is set to "YES". This means that the short dumps (counters) are performed on MS (Main Storage), but not the long dumps. This suggests that the system is configured to only perform short dumps for troubleshooting or monitoring purposes, while long dumps are not enabled.

REMCI is the command used to order the manual interaction of the CP.

DIRCP is the command used to obtain the display of CP EVENT RECORD.

The correct answer is MP=1 because the given statement mentions that the program measures strange voltages (AC and DC), insulation testing, phase angle testing, and capacitance testing. The answer MP=1 indicates that the program is capable of performing these tests.

The correct answer is REU because "REU" is the only option that fits the given description of "la tarjeta que tiene la función de generación de timbre" (the card that has the function of generating a ringtone). The other options, TSW, KRC, and LIB, do not match the given description.

The correct answer is "Registro- Pre análisis - Análisis del número de B - Análisis de ruta". This sequence represents the steps that the switching team takes to select an outgoing route. The first step is to register the call, then perform a preliminary analysis, followed by analyzing the number of B (the called party), and finally, analyzing the route to determine the appropriate outgoing path.

The correct answer is MAS. MAS stands for Maintenance and Administration System. It contains maintenance functions for both the central and regional parts of the control system. This system is responsible for managing and ensuring the smooth operation of the control system by performing maintenance tasks such as monitoring, troubleshooting, and updating the system. It also provides administrative functions for managing user access, permissions, and system configurations.

The correct answer is SYRSI because it is the command used to order a restart to an IOG-20 node.

The correct answer is "PS" because it refers to the "Program Store" or "Program Storage", which is the storage location that contains the system programs.

La señalización de Canal Común permite el manejo de la información de control a través de un enlace distinto al de los canales de voz. Esto significa que se utiliza un canal separado para transmitir la información de control, lo que permite una mayor eficiencia en la comunicación y un mejor manejo de la red.

When a test relay of a LIC is operated (P-86), the speech path between the subscriber line and the line circuit is disconnected, instead, the subscriber line is connected to the SLCT card.

The correct answer is "CP - B haga un diagnóstico de unidades con falla en el CP-A." This means that the CP-B will diagnose the faulty units in CP-A before the CP FAULT alarm is generated.

The correct answer is BLULC. BLULC is the command used to set and/or change the limits of lock supervision. The passage explains that lock supervision verifies the number of locked lines and generates an alarm when a certain limit set by the command is exceeded. Therefore, BLULC fits the description given in the passage.

The correct answer is EMGFD. The given passage mentions that the software of the functional block explores the fault flags in the STC, STR, and RPBC. Among the given options, only EMGFD contains the letters S, T, and R, which are present in the mentioned fault flags. Therefore, EMGFD is the correct answer.

The correct answer is SYRSI - IMCSP - Ver que el nodo pase por los estados: RELOADING, DIAGNOSING, UPDATING, SB/WORKING NORMAL, e IMSIP. This answer states that when performing a recharge on the IOG-20 in the SB node, the node should go through the states of RELOADING, DIAGNOSING, UPDATING, SB/WORKING NORMAL, and IMSIP. This suggests that these specific commands and states are necessary for a successful recharge process on the IOG-20 in the SB node.

The correct answer is the sequence of commands and activities that should be followed to address a failure in EMRP. The sequence starts with ALLIP, followed by EXEPP, REPEI, REMEI, Apagar Fuente, Cambio de Tarjeta, RECEI, Encender Fuentes, EXEPP, and ends with ALLIP. This sequence ensures that the necessary steps are taken to diagnose and fix the failure effectively.

The command "ANBZI" is used in "B-NUMBER" to delete the non-operational table.

The correct answer is STBPS. The question asks for the command that shows only blocked devices. Among the given options, STBPS is the only command that specifically deals with blocked devices. Therefore, it is the correct answer.

The correct answer is BISS. BISS stands for Basic Interoperable Scrambling System. It is a system used to encrypt and decrypt digital video and audio signals in satellite communications. In this context, the card mentioned is a LSM (Line Service Module) card, specifically a P-84 card, which is used to process speech samples from the subscriber. These speech samples are then switched from the PCM channel to a channel belonging to the JTC (Joint Terminal Circuit) Remote Terminal on the ETB card.

La parte del Usuario ISUP se ubica en la capa 4 según el modelo OSI y la señalización No. 7.

The given passage discusses the concept of temporary errors and their causes, stating that they can be caused by circuit failures due to static electricity, software failures, etc. It also mentions that the frequency of temporary errors should not be too high as it can burden the system. If many temporary errors occur in the processor within a comparatively short time, the MAs subsystem will generate an alarm. The passage further explains that the MAs subsystem has the function of software fault management divided into different tasks and it selects the task that does not correspond to this function. Therefore, the correct answer, "Reparacion" (Repair), is the task that does not correspond to the function of software fault management.

The correct answer is TRRPI. This command is used to define a measurement program MP for traffic logging.

DCSAI is the correct answer because it stands for "Data Communications Systems Application Identifier." In the given context, it is the command used to indicate the session identity of a call made by client A.

The correct answer is IMMCT. This command is used to start using the maintenance functions of Input/Output in the SPG.

The correct answer is TSW. In the given context, the LSM card supplies multiple frequencies, including the 8 kHz frame frequency used in all bus systems. TSW stands for Time Slot Window, which is a mechanism used in digital communication systems to allocate time slots for different signals. Therefore, TSW is the most suitable option as it relates directly to the mentioned frequency and its usage in bus systems.

The correct answer is "DUDIR." This is because "DUDIR" is a verb in Spanish that means "to doubt" or "to hesitate." In the given context, the phrase "Reconecta la supervicion de disturbios en ruta de troncales" can be translated as "Reconnect the supervision of disturbances on trunk routes." The word "DUDIR" fits well in this context as it implies a sense of doubt or hesitation in the supervision of disturbances on the specified routes.

The given answer, "EXSLP, IMMCT, IMCSP, INIOP," consists of the commands that are used before starting maintenance activities of the IOG.

The correct answer is ANBZI. This is because the question states that when the command ANBAI is executed and it indicates "CHANGE ALREADY ACTIVATED," the next step to take before entering new data is to use the command ANBZI.

The correct answer is IOROP. This is because IOROP is the command used to request a printout of the routing data from the prints.

The given answer "DOS" is the correct answer because the explanation provided in the question states that the category of a block determines the severity of errors. The category of a block is established during design and assigned to each block in the central data. The category of a block can be modified during the operation of the central. The category of a block does not allow for postponing a restart, meaning an immediate system restart is carried out according to the range. Therefore, "DOS" is the correct answer based on this explanation.

The answer "RPH" is correct because it is mentioned in the given statement that it is part of the structure of CPS and it handles regional processor management.

If the STATUS=OLD is indicated when executing the ANBAI command, the appropriate command to make changes to the table is ANBCI.

The correct answer is EXROI. EXROI is the command used for creating a route while assigning the most important parameters. This command allows for efficient and effective route creation by including all the necessary parameters at the same time.

The correct answer suggests that when performing a short restart on the IOG-20 in the SB node, the command "SYRSI-IMCSP" should be executed to check if the node goes through the states of RELOADING, DIAGNOSING, UPDATING, WORKING, and IMSIP. This command helps in monitoring the progress and status of the node during the restart process.

After receiving an error of comparison between the CP's (MAE), MAU sends the signal MIS to the CP's.

BLURC is the command used to make changes in the device lock supervision of a route.