Shwet (FSC) - 2
-
For this steering and chassis design, these statements have been given. Statement 1- vehicle will pass TI Reason 1 - Steering design is rule compliant Statement 2 - Vehicle will not pass TI Reason 2 - Steering design is not rule compliant Statement 3 - vehicle will pass TI Reason 3 - Position of the pedal and pedal assembly is rule compliant Select the most appropriate option
-
Statement 1 is correct because of Reason 1
-
Statement 2 is correct because of Reason 2
-
Statement 3 is correct because of Reason 3
-
All the above
-
.
Quiz Preview
- 2.
A team has installed its shutdown buttons on the firewall of their vehicle. Which of the following is true?
-
It is non - rule compliant and vehicle will not pass TI
-
It is rule compliant if installed on tertiary firewall of the vehicle and it will pass TI
-
Vehicle will pass TI with consideration from inspector only if documentation is shown
-
None of the above
Correct Answer
A. It is rule compliant if installed on tertiary firewall of the vehicle and it will pass TI -
- 3.
Which of the following front bulkheads cannot be used?
-
Triangular, with the plane of the bulkhead angled at 30 degrees to the ground in side view
-
Crrcular, with the plane of the bulkhead angled at 30 degrees from the ground in side view
-
Square, with the plane of the bulkhead perpendicular to the ground in side view
-
Rectangular, with the plane of the bulkhead angled at 150 degrees from the ground in side view
Correct Answer
A. Crrcular, with the plane of the bulkhead angled at 30 degrees from the ground in side view -
- 4.
A sprocket rotates on your vehicle during the noise test. Your inspector notices there is no finger guard present for that part. Which of the following is true?
-
Noise test will be passes
-
Finger guard is not needed
-
Noise test will be passed
-
Finger guard is needed
Correct Answer
A. Finger guard is not needed -
- 5.
A team has designed its chassis to have the mounts of the shoulder harness to be 53mm and it follows all the structural rules. Which of the following is false?
-
The shoulder harness mounts will be completely rule compliant if they are 180mm apart
-
The shoulder harness mounts will be completely rule compliant if they are 243mm apart
-
All the above
-
None of the above
Correct Answer
A. The shoulder harness mounts will be completely rule compliant if they are 180mm apart -
- 6.
In a collinear collision, a particle with an initial speed Vo strikes a stationary particle of the same mass. If the final total kinetic energy is 50% greater than the original kinetic energy, the magnitude of the relative velocity between the two particles, after collision, is:
-
Vo/2
-
Vo/[2^(1/2)]
-
2^(1/2) * Vo
-
None of the above
Correct Answer
A. 2^(1/2) * Vo -
- 7.
During the TI, the inspector tries to remove one of the wires from the linear POT installed on your teams vehicle. He was unable to do so and then calls to your team mates present. Which of the following is not false?
-
Inspector is wrong and should not have tried to remove one of the electrical wires
-
The inspector will not pass the vehicles TI
-
The inspector will pass the vehicle if team members demonstrate how to remove wire
-
Team members will argue to not remove wires
Correct Answer
A. The inspector will pass the vehicle if team members demonstrate how to remove wire -
- 8.
Your team has scored 81.5 points out of a possible 100 in the autocross event. Which of the following is true?
-
The fastest time given by a team would be 63.9 exactly
-
If the quickest team has a time of 69.33 seconds, the performance factor would be less than 1.25
-
If the quickest team has a time of 69.33 seconds, the performance factor would be greater than 1.25
-
The fastest time given by a team would be 69.33s approx.
Correct Answer
A. The fastest time given by a team would be 69.33s approx. -
- 9.
In a potentiometer experiment, it is found that no current passes through the galvanometer when the terminals of the cell are connected across 52cm of the potentiometer wire. If the cell is shunted by a resistance of 5ohm, a balance is found when the cell is connected across 40cm of the wire. Find the internal resistance of the cell.
-
2 ohm
-
(5/2) ohm
-
1 ohm
-
(3/2) ohm
Correct Answer
A. (3/2) ohm -
- 10.
A solid sphere of radius r made of a soft material of bulk modulus K is surrounded by a liquid in a cylindrical container. A massless piston of area a floats on the surface of the liquid, covering entire cross section of cylindrical container. When a mass m is placed on the surface of the piston to compress the liquid, the fractional decrement in the radius of the sphere, (dr/r) is
-
Ka/(3mg)
-
3ka/mg
-
Ka/mg
-
Ka/3mg
Correct Answer
A. Ka/3mg -
Quiz Review Timeline (Updated): Mar 20, 2022 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 20, 2022Quiz Edited by
ProProfs Editorial Team -
Dec 21, 2019Quiz Created by
Pratik
Back to top