Q-sys Level One Training: Hardware Overview

23 Questions | Total Attempts: 10774

SettingsSettingsSettings
Q-sys Level One Training: Hardware Overview - Quiz

You are about to take the assessment for the Hardware Overview Training Module. Please watch all Hardware overview videos before attempting this assessment. You must correctly answer 80% of the questions to successfully pass this assessment.


Questions and Answers
  • 1. 
    True/False: The only way to get audio input onto a Core is through an I/O Frame.
    • A. 

      True

    • B. 

      False

  • 2. 
    Multiple Choice: What is the maximum number of I/O cards can be housed inside a Core 500i or Core 250i?
    • A. 

      4

    • B. 

      6

    • C. 

      8

  • 3. 
    Multiple Choice: What happens when you press the ID button on the front of the Core?
    • A. 

      The Core will be identified on-screen in the Q-Sys Designer and end-user GUI.

    • B. 

      The name of the Core will appear on the LCD screen.

    • C. 

      The names of the on-board I/O cards will appear on the LCD Screen.

  • 4. 
    Multiple Choice: If the Status LED turns AMBER it means that:
    • A. 

      The Core or I/O Frame is starting or stopping a design.

    • B. 

      The I/O card in the Core or I/O Frame is 3 dB before clipping.

    • C. 

      The signal of the Core or I/O Frame is clipping.

  • 5. 
    Multiple Choice: What is the name of the network protocol that Q-Sys uses?
    • A. 

      Q-LAN

    • B. 

      Q-LINK

    • C. 

      Q-CAT5

  • 6. 
    Choose ALL that apply:What information can you find on the LCD screen of the Core?
    • A. 

      The name of the Core

    • B. 

      The name of the design currently running on the system

    • C. 

      Device model and Firmware version

  • 7. 
    Multiple Choice: What would cause the LCD screen to begin flashing on the Core?
    • A. 

      The current design has hit a critical failure.

    • B. 

      The Core’s temperature has exceeded safe levels.

    • C. 

      Someone has clicked the Core’s corollary ID button in the Designer software.

  • 8. 
    Multiple Choice: Through which connection on the Core’s back panel does the Core connect to Q-LAN?
    • A. 

      Q-Sys Network

    • B. 

      Serial RS232

    • C. 

      GPIO

  • 9. 
    Multiple Choice: What does GPIO stand for?
    • A. 

      General Purpose Input Output

    • B. 

      Global Power Input Outlet

    • C. 

      Generic Proprietary Input Output

  • 10. 
    Multiple Choice: How is the Q-Sys Core powered?
    • A. 

      Universal Power Supply

    • B. 

      Dilithium Crystals

  • 11. 
    Multiple Choice: What color will an I/O Card’s Status LED become to indicate that the corollary audio signal is -3dB below clipping?
    • A. 

      Green

    • B. 

      Yellow

    • C. 

      Red

  • 12. 
    Multiple Choice: How do you cycle through the basic housekeeping information on the LCD display?
    • A. 

      Press the Page or Next button

    • B. 

      Press the ID button

  • 13. 
    Multiple Choice: Which I/O Card should you use to connect a non-Dataport-enabled amplifier?
    • A. 

      COL4

    • B. 

      CCN32

    • C. 

      CODP4

  • 14. 
    CHECK ALL THAT APPLYWhich of the following is considered a peripheral device? Check all that apply.
    • A. 

      I/O Frame

    • B. 

      I/O-22

    • C. 

      Page Station

    • D. 

      TouchScreen

    • E. 

      Core 500i

  • 15. 
    CHECK ALL THAT APPLYWhich of the following are features of the I/O-22?
    • A. 

      Two mic/line inputs

    • B. 

      Two line outputs

    • C. 

      8.5 watt mono amplifier

    • D. 

      Gooseneck or Handheld microphone option

  • 16. 
    MULTIPLE CHOICEWhat is the primary purpose of a QSC TouchScreen Controller?
    • A. 

      To display an interactive User Control Interface

    • B. 

      To provide command control over a Page Station

    • C. 

      To allow remote access to the design Schematic

    • D. 

      To play videos or other multimedia

  • 17. 
    MULTIPLE CHOICEHow can you add a peripheral to your design?
    • A. 

      Go to the Inventory pane, click the Plus Icon, select Peripherals, and add your device

    • B. 

      Once the peripheral is connected to your network, it will automatically be added to your design

    • C. 

      Drag the desired peripheral from the Peripheral Components branch of the Schematic Library

    • D. 

      Hold the Connect button for three seconds on both the peripheral and the Core to sync devices

  • 18. 
    Multiple ChoiceIn terms of your Q-Sys system, what is a PS-X?
    • A. 

      Additional Paging Handset

    • B. 

      I/O Connection Module

    • C. 

      Portable Gaming System

  • 19. 
    True or False:The Q-Sys TouchScreen TSC-7t and TSC-7w can be powered over Ethernet.
    • A. 

      True

    • B. 

      False

  • 20. 
    True/FalseThe I/O-22 is the only option for additional remote I/O boxes on a Q-Sys system.
    • A. 

      True

    • B. 

      False

  • 21. 
    Multiple ChoiceAmplifier Redundancy is made possible with the use of which device?
    • A. 

      DAB-801

    • B. 

      TSC-7t

    • C. 

      TSC-7w

  • 22. 
    Check all that applyWhat forms of redundancy are possible on a Q-Sys system?  Check all that apply.
    • A. 

      Core Redundancy

    • B. 

      Input/Output Redundancy

    • C. 

      Network Redundancy

  • 23. 
    Multiple ChoiceHow many Q-LAN Ethernet ports are available on each Q-Sys Core?
    • A. 

      2

    • B. 

      1

    • C. 

      3

Back to Top Back to top