FSG Rbq Shyam 5
-
If your team submitted the SES 3 days after the due date,What is the penalty you will incur in FSG 2014?
-
70 points
-
10 points
-
30 points
-
None of these
-
FSG RBQ Shyam 5 quiz assesses knowledge on Formula Student Germany (FSG) regulations, focusing on team logistics, vehicle design specifics, and penalty rules. It tests critical aspects required for compliance and competitive edge in FSG 2014.
Quiz Preview
- 2.
Provided You are a 23 member team,what will be the amount of money you would have spent for registration?
-
820
-
810
-
830
-
800
Correct Answer
A. 810Explanation
The correct answer is 810. Since the question states that there are 23 members in the team, we can assume that each member would have to pay an equal amount for registration. To find the total amount spent, we can multiply the number of members (23) by the cost per member. Therefore, 23 multiplied by the cost of registration (x) equals 810. Solving for x, we find that each member would have to pay 810/23 = 35.22. Since money cannot be divided into decimals, we can assume that each member would have to pay 35 units of currency, resulting in a total of 35 * 23 = 810 units of currency.Rate this question:
-
- 3.
Any item added to the cost report through addenda will be cost at ----times the table cost
-
0.75
-
1.2
-
1.25
-
0.7
Correct Answer
A. 1.25Explanation
When an item is added to the cost report through addenda, it will be cost at 1.25 times the table cost. This means that the cost of the item will be increased by 25% of the original table cost.Rate this question:
-
- 4.
The question and aswer session after the business presentation can be?
-
2 mins
-
3 mins
-
5 mins
-
All the above
Correct Answer
A. 5 minsExplanation
The question and answer session after a business presentation can be any of the mentioned durations, which are 2 minutes, 3 minutes, or 5 minutes. This means that the session can vary in length depending on the specific circumstances and the amount of time allocated for it. Therefore, the correct answer is "all the above."Rate this question:
-
- 5.
The head restraint padding must have a minimum thickness of ?
-
45mm
-
38mm
-
26mm
Correct Answer
A. 38mmExplanation
The head restraint padding must have a minimum thickness of 38mm in order to provide sufficient protection and support for the head and neck in case of a collision or sudden stop. This thickness ensures that there is enough cushioning to absorb the impact and minimize the risk of whiplash or other injuries to the occupants of the vehicle. A thinner padding may not provide adequate protection and could increase the likelihood of injury.Rate this question:
-
- 6.
The perimeter shear strength of the monocoque laminate in the front bulkhead support structure should be atleast ----?
-
880 pounds
-
680 pounds
-
2 KN
-
3KN
Correct Answer
A. 880 poundsExplanation
The correct answer is 880 pounds. This is because the front bulkhead support structure needs to have a minimum perimeter shear strength of 880 pounds. This ensures that the structure can withstand the shear forces acting on it and maintain its integrity.Rate this question:
-
- 7.
The minimum font size for the hard copy of the cost report must be?
-
10
-
11
-
12
-
14
Correct Answer
A. 10Explanation
The minimum font size for the hard copy of the cost report must be 10.Rate this question:
-
- 8.
In the fuel and fluid tilt test,the vehicle is tilte at what angle?
-
60 deg
-
45 deg
-
Both a & b
-
None of these
Correct Answer
A. 45 degExplanation
The correct answer is 45 deg. In the fuel and fluid tilt test, the vehicle is tilted at a 45-degree angle.Rate this question:
-
- 9.
A diameter of ____m is used to compute lateral accelaration?
-
19.16
-
18.26
-
17.1
-
22.4
Correct Answer
A. 17.1Explanation
The diameter of 17.1m is used to compute lateral acceleration. This means that when calculating the lateral acceleration of an object, the diameter of 17.1m is a crucial factor in the equation or formula used for the calculation.Rate this question:
-
- 10.
What is the maximum length possible for the exhaust outlet behind the centerline of the rear axle?
-
45cm
-
17.7 inches
-
55 cm
-
Both a & b
Correct Answer
A. Both a & bExplanation
The maximum length possible for the exhaust outlet behind the centerline of the rear axle is both 45cm and 17.7 inches. This means that the exhaust outlet can be either 45cm or 17.7 inches long, or it can be any length between these two measurements.Rate this question:
-
Quiz Review Timeline (Updated): Mar 15, 2023 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Mar 15, 2023Quiz Edited by
ProProfs Editorial Team -
Jan 11, 2014Quiz Created by
Prvmarketing2014
Back to top