Fire Guard Preparation Course
Fire guards have been used to warm up a house when winter comes. Not everyone has the capability to prepare one safely. Preparing one for the house is no easy task. Test out if you are ready to do that by taking up the quiz below. All the best and stay safe!
Questions and Answers
- 1.
There must be a minimum of three pull stations per floor?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is false because there is no requirement for a minimum of three pull stations per floor. The number of pull stations required per floor may vary depending on the building's size, layout, and fire safety regulations.Rate this question:
-
- 2.
What is the maximum distance between pull stations?
- A.
100 ft
- B.
300 ft
- C.
75 ft
- D.
200 ft
Correct Answer
D. 200 ftExplanation
The maximum distance between pull stations is 200 ft. This means that the pull stations, which are used to activate fire alarm systems, can be located up to 200 ft apart from each other. Beyond this distance, it may be difficult for individuals to reach a pull station in case of an emergency, potentially delaying the activation of the fire alarm system and the response to the fire.Rate this question:
-
- 3.
Which is used to shut off the fire alarm?
- A.
Pull Station
- B.
Roof Manifold
- C.
Control Panel
- D.
None of the above
Correct Answer
C. Control PanelExplanation
The control panel is used to shut off the fire alarm. It is the central hub where all the fire alarm system components are connected, allowing for monitoring and control of the system. The control panel typically has buttons or switches that can be used to silence or reset the alarm, as well as to activate or deactivate specific zones or devices. It provides a convenient and centralized way to manage the fire alarm system and respond to any alarms or faults.Rate this question:
-
- 4.
The three types of pull stations are single action, double action, and interior?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is false because the three types of pull stations are actually single action, double action, and manual. The term "interior" is not used to categorize pull stations.Rate this question:
-
- 5.
Minimum safe distance for a fire is?
- A.
100 ft
- B.
200 ft
- C.
400 ft
- D.
300 ft
Correct Answer
D. 300 ftExplanation
The minimum safe distance for a fire is 300 ft. This distance is necessary to ensure the safety of individuals and property in case of a fire. Being at least 300 ft away from the fire helps to prevent the spread of flames, heat, and smoke, reducing the risk of injury or damage. It also allows emergency responders to work efficiently without obstruction. Therefore, maintaining a distance of 300 ft is crucial for safety during a fire incident.Rate this question:
-
- 6.
An exit aisle of how many feet is required in all locations?
- A.
5 ft
- B.
7 ft
- C.
3 ft
- D.
9 ft
Correct Answer
C. 3 ftExplanation
In all locations, an exit aisle of 3 feet is required. This means that there should be a clear pathway with a width of 3 feet for people to safely exit a location in case of an emergency. This is a standard requirement to ensure the smooth and efficient evacuation of people from a building or any other crowded area.Rate this question:
-
- 7.
Self closing doors must be proped open?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Self-closing doors are designed to automatically close after being opened, without the need for someone to physically close them. Therefore, they do not need to be propped open as they are intended to close on their own.Rate this question:
-
- 8.
Pull stations must be tested?
- A.
Weekly
- B.
Monthly
- C.
Yearly
- D.
Daily
Correct Answer
D. DailyExplanation
Pull stations must be tested daily to ensure they are in proper working condition and ready to be used in case of an emergency. Daily testing allows for immediate identification of any issues or malfunctions, ensuring that the pull stations are reliable and can be easily activated when needed. Regular testing also helps to maintain compliance with safety regulations and standards.Rate this question:
-
- 9.
Which pull station has a white stripe painted on it?
- A.
Single Action
- B.
Double Action
- C.
Interior
- D.
Exterior
Correct Answer
B. Double ActionExplanation
A double action pull station has a white stripe painted on it. This stripe is used to indicate that the pull station is a double action type, meaning it requires two separate actions to activate the alarm. This is usually done to prevent accidental activations and to ensure that the alarm is only triggered intentionally.Rate this question:
-
- 10.
Fire Guard logbook must be kept for how long?
- A.
One Year
- B.
Two Years
- C.
Three Years
- D.
Four Years
- E.
Five Years
Correct Answer
C. Three YearsExplanation
The Fire Guard logbook must be kept for three years. This is important for record-keeping purposes and to ensure that the information in the logbook is readily available if needed. Keeping the logbook for this duration allows for easy access to past fire incidents, inspections, and maintenance records, which can be crucial in assessing fire safety measures and identifying any patterns or issues that need to be addressed.Rate this question:
-
- 11.
Extinguishers must be recharged after each time they are used?
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Extinguishers must be recharged after each time they are used because once an extinguisher has been discharged, it needs to be refilled with the extinguishing agent in order to be ready for future use. This ensures that the extinguisher is fully functional and can effectively suppress fires. Recharging also allows for any damaged or worn-out parts to be replaced, ensuring the extinguisher is in proper working condition. Neglecting to recharge an extinguisher after use can render it useless in case of another fire emergency. Therefore, it is essential to recharge extinguishers after each use to maintain their effectiveness.Rate this question:
-
- 12.
Fires involving electrical equipment are a class?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
C. Class CExplanation
Fires involving electrical equipment are classified as Class C fires. Class C fires involve energized electrical equipment such as appliances, wiring, circuit breakers, and outlets. These fires can be caused by electrical malfunctions, short circuits, or overloaded circuits. It is important to use a fire extinguisher specifically designed for Class C fires, as using water or other conductive agents can lead to electrical shock.Rate this question:
-
- 13.
Fires involving combustable metals are a class?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
D. Class DExplanation
Fires involving combustible metals are classified as Class D fires. Class D fires involve materials such as magnesium, titanium, sodium, potassium, and other similar metals that can ignite and burn at high temperatures. These fires require special extinguishing agents, such as dry powder or sand, as water can react with the metal and worsen the situation. Class D fires are less common than other classes of fires but can be extremely dangerous if not properly handled.Rate this question:
-
- 14.
Fires involving flammable liquids are a class?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
B. Class BExplanation
Fires involving flammable liquids are classified as Class B fires. Flammable liquids include substances such as gasoline, oil, and alcohol. Class B fires are characterized by the presence of flammable or combustible liquids, and they require the use of extinguishing agents that can smother the flames and prevent the spread of the fire. These fires can be extremely dangerous and can spread quickly if not properly controlled. Therefore, it is important to use the appropriate fire extinguisher and follow safety protocols when dealing with Class B fires.Rate this question:
-
- 15.
Fires involving wood, paper or cloth equipment are a class?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
A. Class AExplanation
Class A fires involve ordinary combustible materials such as wood, paper, and cloth. These fires are typically fueled by organic materials and can be extinguished by cooling the burning material and removing the oxygen supply. Class A fires are the most common type of fire and can occur in residential, commercial, and industrial settings. They are often extinguished using water or water-based extinguishers.Rate this question:
-
- 16.
The fire triangle include?
- A.
Fuel, heat and air
- B.
Earth, wind and fire
- C.
Oxygen, fuel and heat
Correct Answer
C. Oxygen, fuel and heatExplanation
The fire triangle refers to the three elements necessary for a fire to occur: oxygen, fuel, and heat. Oxygen is required to sustain the combustion process, fuel provides the material that can burn, and heat is needed to initiate and maintain the fire. Without any one of these elements, a fire cannot exist.Rate this question:
-
- 17.
You must have six extra sprinkler heads and a wrench an property at all times?
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
Having six extra sprinkler heads and a wrench on the property at all times is necessary for maintenance and repairs. Sprinkler heads can get damaged or worn out over time, and having extra ones ensures that they can be quickly replaced if needed. The wrench is essential for installing and adjusting the sprinkler heads. By having these tools readily available, any issues with the sprinkler system can be promptly addressed, ensuring proper irrigation and preventing potential damage to the landscape.Rate this question:
-
- 18.
There is no such thing as a multi-purpose fire extinguisher?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement "There is no such thing as a multi-purpose fire extinguisher" is false. Multi-purpose fire extinguishers are designed to extinguish different types of fires, such as Class A (ordinary combustibles), Class B (flammable liquids and gases), and Class C (electrical fires). These extinguishers are versatile and can be used in various settings, making them a valuable tool for fire safety.Rate this question:
-
- 19.
With which extinguisher can you stand 15 ft away from the fire?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
A. Class AExplanation
Class A fire extinguishers are designed to extinguish fires involving ordinary combustible materials such as wood, paper, cloth, and plastics. These extinguishers typically use water or foam as the extinguishing agent. Since Class A fires do not involve flammable liquids or gases, it is generally safe to stand 15 ft away from the fire while using a Class A extinguisher.Rate this question:
-
- 20.
If the needle in an extinguisher's guage is pointing to the green area, that means?
- A.
Ready to use
- B.
Over-charged
- C.
Discharged
- D.
None of the above
Correct Answer
A. Ready to useExplanation
If the needle in an extinguisher's gauge is pointing to the green area, it means that the extinguisher is ready to use. This indicates that the pressure inside the extinguisher is within the recommended range, ensuring that it will function properly when needed.Rate this question:
-
- 21.
Which sprinkler system is used in an outdoors parking lot?
- A.
Wet System
- B.
Dry System
- C.
Deluge System
- D.
None of the above
Correct Answer
D. None of the aboveExplanation
None of the above options are suitable for an outdoor parking lot. In an outdoor setting, a pre-action sprinkler system is typically used. This system combines elements of both wet and dry systems, allowing water to flow into the pipes only when a fire is detected. This helps prevent accidental activation due to environmental factors such as rain or snow. Therefore, the correct answer is "None of the above."Rate this question:
-
- 22.
In what position is the OS&Y valve if the stem is fully extended?
- A.
Open
- B.
Closed
- C.
Mid-way
Correct Answer
A. OpenExplanation
When the stem of an OS&Y (Outside Screw and Yoke) valve is fully extended, it means that the valve is fully open. In an OS&Y valve, the stem moves up and down to control the flow of fluid. When the stem is fully extended, it indicates that the valve is in the open position, allowing the fluid to flow freely through the valve. Therefore, the correct answer is "Open".Rate this question:
-
- 23.
Pull stations must be mounted six feet up from the floor?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Pull stations do not have to be mounted six feet up from the floor. The height at which pull stations are mounted can vary depending on the specific fire code regulations and guidelines of a particular jurisdiction. The purpose of mounting pull stations at a certain height is to ensure that they are easily accessible and visible in case of an emergency. However, the exact height requirements may differ, and it is important to consult the relevant fire code regulations for accurate information.Rate this question:
-
- 24.
The OS&Y valve is inspected how often?
- A.
Weekly
- B.
Monthly
- C.
Yearly
- D.
Daily
Correct Answer
C. YearlyExplanation
The OS&Y valve is inspected yearly because it is not a critical component that requires frequent monitoring. Inspecting it on a yearly basis ensures that it is in proper working condition and can be maintained accordingly. Daily or weekly inspections would be excessive for this type of valve, while monthly inspections may not provide sufficient time to identify any potential issues. Therefore, a yearly inspection interval strikes a balance between ensuring the valve's functionality and avoiding unnecessary inspections.Rate this question:
-
- 25.
Fire Guards must patrol how often?
- A.
Every Hour
- B.
Every Two Hours
- C.
Every Four Hours
- D.
Every Eight Hours
Correct Answer
A. Every HourExplanation
Fire Guards must patrol every hour to ensure the safety of the premises. This frequent patrolling allows them to quickly identify any potential fire hazards, monitor the effectiveness of fire prevention measures, and respond promptly in case of an emergency. Regular patrols help to minimize the risk of fire incidents and ensure that any issues are addressed promptly, reducing the potential for damage and harm to people and property.Rate this question:
-
- 26.
The Fire Guard must first activate the fire alarm then notify the Fire Department?
- A.
True
- B.
False
Correct Answer
A. TrueExplanation
The fire guard must first activate the fire alarm to alert everyone in the building about the potential fire hazard. Once the alarm is activated, they should immediately notify the fire department to ensure that professional help is on the way. This sequence of actions is crucial in order to ensure the safety of all individuals present in the building and to minimize the risk of any further damage caused by the fire.Rate this question:
-
- 27.
When an exterior pull station is used, the Fire Guard must wait in the lobby?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement "When an exterior pull station is used, the Fire Guard must wait in the lobby" is false. When an exterior pull station is used, the Fire Guard does not necessarily have to wait in the lobby. The Fire Guard's role is to respond to fire emergencies and take appropriate actions, such as activating the fire alarm, evacuating the building, and notifying emergency services. Depending on the situation, the Fire Guard may need to assess the situation outside the building, coordinate with other emergency personnel, or assist with the evacuation process.Rate this question:
-
- 28.
The Fire Safety Plan should not be posted by phones because of fals alarms?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The statement is incorrect. The Fire Safety Plan should not be posted by phones because phones are not a reliable means of communication during emergencies. Phone lines can be disrupted or busy, making it difficult for people to access the Fire Safety Plan when they need it the most. Instead, the Fire Safety Plan should be posted in visible and easily accessible areas within the premises to ensure everyone can quickly and easily access it during an emergency.Rate this question:
-
- 29.
Sprinkler heads can withstand how many pounds of pressure (PSI)?
- A.
16 PSI
- B.
15 PSI
- C.
200 PSI
- D.
500 PSI
- E.
None of the above
Correct Answer
D. 500 PSIExplanation
Sprinkler heads are designed to withstand high water pressure in order to effectively distribute water. The correct answer of 500 PSI indicates that sprinkler heads can handle up to 500 pounds of pressure per square inch. This high pressure tolerance ensures that the sprinkler system can function properly and deliver water to the desired areas without any damage or leakage.Rate this question:
-
- 30.
Cycling Sprinkler Heads activate at what temperture?
- A.
150 degrees
- B.
130 degrees
- C.
100 degrees
- D.
165 degrees
Correct Answer
D. 165 degrees -
- 31.
What diameter size circle on the floor do sprinkler head make using water?
- A.
9 ft
- B.
7 ft
- C.
12 ft
- D.
16 ft
- E.
20 ft
Correct Answer
D. 16 ftExplanation
The sprinkler head creates a circle with a diameter of 16 ft on the floor using water.Rate this question:
-
- 32.
What is the Fire Guards area of responsibility?
- A.
220 ft
- B.
5 ft
- C.
75 ft
- D.
150 ft
- E.
None of the above
Correct Answer
C. 75 ftExplanation
The Fire Guards area of responsibility is 75 ft. This means that the Fire Guard is responsible for ensuring the safety and security of an area within a radius of 75 ft. They must be vigilant and alert to any potential fire hazards or emergencies within this designated area. Their primary role is to prevent fires and respond promptly in case of any fire-related incidents within their jurisdiction.Rate this question:
-
- 33.
The Fire Saftey Plan should not be posted at the front desk?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The Fire Safety Plan should be posted at the front desk. This is because the front desk is a central location where staff and visitors can easily access the plan in case of an emergency. By having the plan visible and easily accessible, it ensures that everyone in the building is aware of the procedures to follow in case of a fire.Rate this question:
-
- 34.
Fire Safety Plan must be approved by?
- A.
Fire Safety Director
- B.
Fire Guard
- C.
Fire Department
- D.
Fire Safety Coordinator
Correct Answer
C. Fire DepartmentExplanation
A Fire Safety Plan must be approved by the Fire Department because they are responsible for ensuring that all fire safety regulations and protocols are followed. The Fire Department has the expertise and authority to review and approve the plan to ensure that it meets all necessary requirements and standards for fire safety. They have the knowledge and experience to assess the plan and make sure that it includes all necessary precautions and measures to prevent and respond to fire emergencies effectively.Rate this question:
-
- 35.
All emergency exits must always be locked?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
Emergency exits should never be locked as they need to be easily accessible in case of an emergency. Locking them would create a potential hazard and prevent people from quickly exiting a building in the event of a fire, natural disaster, or any other emergency situation. Keeping emergency exits unlocked allows for a safe and efficient evacuation, ensuring the well-being of individuals inside the building.Rate this question:
-
- 36.
Smoke detector are tested once every?
- A.
Day
- B.
Week
- C.
Six Months
- D.
Year
Correct Answer
C. Six MonthsExplanation
Smoke detectors are tested once every six months to ensure their functionality and effectiveness in detecting smoke and triggering an alarm. Regular testing is necessary to ensure that the smoke detector's sensors, batteries, and other components are in working order. By testing every six months, homeowners can be confident that their smoke detectors will provide early warning in case of a fire, allowing them to take appropriate action and potentially save lives.Rate this question:
-
- 37.
During a fire the first and last floors are the first to be evacuated?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
The given answer is False. During a fire, the first and last floors are not necessarily the first to be evacuated. The order of evacuation depends on various factors such as the location and severity of the fire, the availability of escape routes, and the proximity of individuals to those routes. It is important to follow the instructions of emergency personnel and evacuate in an orderly manner, prioritizing the safety of all individuals.Rate this question:
-
- 38.
How many Fire Guards are required for a building 375 ft in height?
- A.
2 Guards
- B.
3 Guards
- C.
4 Guards
- D.
5 Guards
Correct Answer
D. 5 GuardsExplanation
A building that is 375 ft in height requires 5 fire guards. This is because fire codes typically require one fire guard for every 75 ft of height. Therefore, for a building that is 375 ft tall, 5 fire guards would be necessary to ensure proper safety measures are in place.Rate this question:
-
- 39.
Fire Guards for a construction site must be on duty 24 hours a day?
- A.
True
- B.
False
Correct Answer
B. FalseExplanation
False. Fire guards for a construction site do not need to be on duty 24 hours a day. While it is important to have fire guards present during construction activities, they typically work in shifts to ensure continuous coverage. This helps to prevent and respond to any potential fire hazards or emergencies that may arise on the site. However, it is not necessary for fire guards to be on duty round the clock.Rate this question:
-
- 40.
If a building's issued a summons for lack of fire guards, how long do they have to correct it?
- A.
24 hours
- B.
48 hours
- C.
72 hours
- D.
84 hours
Correct Answer
C. 72 hoursExplanation
If a building is issued a summons for lack of fire guards, they have 72 hours to correct the issue. This means that within 72 hours, the building must implement the necessary fire guards to comply with safety regulations. Failure to do so within the given time frame may result in further consequences or penalties.Rate this question:
-
- 41.
In Torch Operation which color hose is for oxygen?
- A.
Green
- B.
Black
- C.
Purple
- D.
Red
Correct Answer
A. GreenExplanation
The green hose is used for oxygen in Torch Operation.Rate this question:
-
- 42.
In Torch Operation which color hose is for Propane?
- A.
Green
- B.
Black
- C.
Purple
- D.
Red
Correct Answer
D. RedExplanation
The color red is used to indicate that the hose is meant for propane in torch operations.Rate this question:
-
- 43.
In Torch Operation which color hose is for Acetylene?
- A.
Green
- B.
Black
- C.
Purple
- D.
Red
Correct Answer
B. BlackExplanation
The color of the hose for Acetylene in Torch Operation is black. Different colors are used for different gases to avoid confusion and ensure safety. Black is specifically designated for Acetylene to indicate that it is the hose for this particular gas.Rate this question:
-
- 44.
How often is a Hydrostatic test done on a extinguisher?
- A.
Weekly
- B.
Monthly
- C.
Yearly
- D.
Every Two Years
Correct Answer
D. Every Two YearsExplanation
A hydrostatic test is conducted to ensure the structural integrity and safety of a fire extinguisher. It involves pressurizing the extinguisher to a level higher than its normal operating pressure and checking for any leaks or weaknesses in the container. Conducting this test every two years is considered sufficient to identify any potential issues and prevent accidents. Weekly or monthly tests would be too frequent and unnecessary, while a yearly test might not provide enough time to detect any gradual deterioration of the extinguisher's components.Rate this question:
-
- 45.
On what class of fire do you use a CO2 Extinguisher?
- A.
Class A
- B.
Class B
- C.
Class C
- D.
Class D
- E.
Class K
Correct Answer
C. Class CExplanation
A CO2 extinguisher is used on Class C fires, which involve energized electrical equipment such as appliances, wiring, circuit breakers, and outlets. CO2 extinguishers work by displacing the oxygen around the fire, effectively smothering it and extinguishing the flames. This type of extinguisher does not leave any residue or cause damage to the electrical equipment, making it a safe and effective choice for Class C fires.Rate this question:
-
- 46.
Pull Stations must be painted what color?
- A.
Green
- B.
Black
- C.
Purple
- D.
Red
Correct Answer
D. RedExplanation
Pull stations must be painted red because red is the standard color used to indicate emergency equipment and devices. This color is easily recognizable and helps people quickly locate and identify pull stations in case of an emergency. Painting pull stations in any other color could cause confusion and delay in activating the alarm or alerting authorities.Rate this question:
-
Quiz Review Timeline +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Sep 08, 2023Quiz Edited by
ProProfs Editorial Team -
Nov 15, 2011Quiz Created by
EbonyGlamDotcom
Back to top