1.
True or False
ISO is only a reactive respond for the IC?
2.
In the Charte of all three events (rate of change, danger, Activity), when is the ISO truly needed?
A. 
B. 
C. 
D. 
3.
True or FalseAt this time are Residential fires hurting and killing Firefighters?
4.
At what point does the IC need to think that his Span of control is spread out to thin and needs to assign an ISO.
A. 
B. 
C. 
D. 
5.
As an ISO duty, what is another thing that may be required to be done in some jurisdiction, in response to Firefighter down, missing, or injured?
A. 
Check and see that everyone is wearing full PPE
B. 
Make sure that there is no overhead wires
C. 
Documentation and investigation
D. 
Nothing at all, just a trick question
6.
Where does the Safety officer come from, Four of the five are recommended from the book which one is not?
A. 
Training or Safety officer
B. 
Health and safety Committee members
C. 
Firefighters II with OHSA cert from CRF 29
D. 
E. 
7.
What is the difference in Efficiency and Effectiveness?
A. 
Efficiency is doing the things right, and Effectiveness is doing the right thing
B. 
If you handle the incident 90% efficient and effectiveness
C. 
Efficiency is your right, Effectiveness is the right
D. 
Efficiency and Effectiveness are the same thing
8.
______ is the acquisition of the knowledge, skills, and attitude needed to achieve mastery.
A. 
B. 
C. 
D. 
9.
______ is the demonstration of acquired mastery in the incident environment.
A. 
B. 
C. 
D. 
10.
The ISO should have the Knowledge to classify a building with regard to occupancy type, construction type, and materials used.
A. 
B. 
C. 
Physiology, kinesiogogy, and injury potential
D. 
11.
The ISO must decide if the action being implemented presents an acceptable risk to those taking it.
A. 
B. 
C. 
Physiology, kinesiogogy, and injury potential
D. 
12.
Can the ISO predict crew rehab needs, size up ergonomic stressors, and predict the injury potential for firefighters operating in an environment
A. 
B. 
C. 
D. 
Physiology, kinesiogogy, and injury potential
13.
When a building is a design what are some of the forces it must stand up to, all but one of the following.
A. 
B. 
C. 
D. 
E. 
14.
When talking about loads transmitted through a structural member there are three types, which one of these are not one.
A. 
B. 
C. 
D. 
15.
When talking about the Loads that are applied to a structural member there are three, which one of the following is not one.
A. 
B. 
C. 
D. 
16.
True or False
The Mass (or Density) of a material directly impacts its fire resistance.
17.
True or False
Only Wood, Steel, concrete and masonry` are used in building construction.
18.
Which is one of the only Material that will bend when under stress and fire?
A. 
B. 
C. 
D. 
19.
When a 100ft long steel beam reaches the degrees of 1000* Fahrenheit, how much can it elongate?
A. 
B. 
C. 
D. 
E. 
20.
True or False
Cooling structural steel with fire streams can have no effect or worse, may cause failure.
21.
The term spalling is
A. 
B. 
C. 
D. 
22.
True or FalseMasonry units with mortar have little tensile or shear strength?
23.
True or False
Only direct flame touching a wooden I beam made with Laminated veneer lumber(LVL) or Oriented strand board(OSB) can cause it to fail.
24.
Any structural component that transmits a compressive force parallel through its centre is called a _____.
A. 
B. 
C. 
D. 
25.
A structural element that delivers loads perpendicularly to its imposed load is called a _____.
A. 
B. 
C. 
D.