Orientation Quiz

20 Questions | By Moretrench | Updated: Mar 3, 2016 | Attempts: 147

Questions

Settings

Create your own Quiz

Questions and Answers

1.

The ESRM is issued to each employee and contains a condensed version of the Moretrench safety policies and procedures.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
2.

Moretrench issued hardhats must be worn at all times when in the field, except in offices and lunchrooms. Ball caps shall not be worn under hardhats.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
3.

You should not lift anything by yourself that weighs over:
- A.
  
  50 pounds
- B.
  
  30 pounds
- C.
  
  15 pounds
- D.
  
  75 pounds
Correct Answer
A. 50 pounds
4.

PASS stands for:
- A.
  
  Sweep
- B.
  
  Push
- C.
  
  Aim
- D.
  
  Saw
- E.
  
  Squeeze
- F.
  
  Pull
- G.
  
  Air
- H.
  
  Spark
Correct Answer(s)
A. Sweep
C. Aim
E. Squeeze
F. Pull
5.

A guard is a physical barrier which prevents contact with a hazard.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
6.

The wellpoint system was designed to dewater the work sites and dry excavations.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
7.

Moretrench is made up of many divisions including geotechnical, civil, concrete, and mechanical.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
8.

According to the Moretrench "Bill of Rights" - You have the right and responsibility, when knowledgeable of job hazards, to STOP work, without fear of reprisal, to protect co-workers, others and yourself from imminent hazard situations.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
9.

As a Short Service Employee (SSE) I am required to wear an orange hardhat for the first six months, I will be drug screened once amonth for the first six months, and will also be subject to the random company wide drug and alcohol screening.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
10.

The STARRT process is the corner stone of the Moretrench safety process. Pick ALL elements below that discribe this process.
- A.
  
  Define the Task
- B.
  
  Analyze the Hazard
- C.
  
  Determine what time lunch will be
- D.
  
  Develop Controls
- E.
  
  Feedback and improvement
- F.
  
  Inspect Area
Correct Answer(s)
A. Define the Task
B. Analyze the Hazard
D. Develop Controls
E. Feedback and improvement
11.

A good STARRT will paint a mental picture for the employees working on the task, and will give anyone not familiar with the site a basic understanding of the type of work in the area.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
12.

The Safety Hazard Observation Wheel (SHOW) is a tool that Moretrench has developed to assist you in determining the hazards present.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
13.

If during the course of work any deviation occurs from the conditions identified in the Description of Task, Task Steps, Hazards, Recommended Corrective Action, as outlined on the STARRT form:
- A.
  
  Stop Work Authority must be invoked
- B.
  
  Newly Identified Hazard(s) documented
- C.
  
  Additional safe practices identified
- D.
  
  A Re- STARRT shall be conducted
Correct Answer(s)
A. Stop Work Authority must be invoked
B. Newly Identified Hazard(s) documented
C. Additional safe practices identified
D. A Re- STARRT shall be conducted
14.

Stop-STARRT should not be confused with the Human Performance Improvement Tool, Stop When Unsure, which is a temporary stoppage of work by the individual performing the task to assure that they themselves are performing the task correctly.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
15.

How to use ‘Stop When Unsure’ check all that apply:
- A.
  
  Obtain information from a book, drawing, procedure, or expert.
- B.
  
  Ask your supervisor or co-worker to verify that your actions are correct.
- C.
  
  Stand back and re-evaluate the potential hazards and consequences.
- D.
  
  Every person has the responsibility and authority to stop work when uncertainty exists.
Correct Answer(s)
A. Obtain information from a book, drawing, procedure, or expert.
B. Ask your supervisor or co-worker to verify that your actions are correct.
C. Stand back and re-evaluate the potential hazards and consequences.
D. Every person has the responsibility and authority to stop work when uncertainty exists.
16.

Always report every injury or incident IMMEDIATELY to your supervisor or a Safety Representative .
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
17.

Seatbelts shall be worn at all times while operating or riding in a company vehicle or Mobile equipment. (NO SEAT BELT / NO RIDE)
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
18.

All vehicles & mobile equipment shall have a daily inspection and the appropriate inspection form shall be completed. Report any defects to your supervisor.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
19.

Safety toed boots meeting the ANSI Z41.1 requirements must be worn on ALL worksites. ALL BOOTS SHALL BE LACE UP.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True
20.

Damaged or defective electrical tools must be removed from service immediately for disposal or repair. Ensure that damaged or defective tools are tagged with “Danger Do Not Use” tags.
- A.
  
  True
- B.
  
  False
Correct Answer
A. True

Quiz Review Timeline +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

Current Version
Mar 03, 2016

Quiz Edited by
ProProfs Editorial Team
Apr 28, 2015

Quiz Created by
Moretrench

Orientation Quiz

The ESRM is issued to each employee and contains a condensed version of the Moretrench safety policies and procedures.

Moretrench issued hardhats must be worn at all times when in the field, except in offices and lunchrooms. Ball caps shall not be worn under hardhats.

You should not lift anything by yourself that weighs over:

PASS stands for:

A guard is a physical barrier which prevents contact with a hazard.

The wellpoint system was designed to dewater the work sites and dry excavations.

Moretrench is made up of many divisions including geotechnical, civil, concrete, and mechanical.

According to the Moretrench "Bill of Rights" - You have the right and responsibility, when knowledgeable of job hazards, to STOP work, without fear of reprisal, to protect co-workers, others and yourself from imminent hazard situations.

As a Short Service Employee (SSE) I am required to wear an orange hardhat for the first six months, I will be drug screened once amonth for the first six months, and will also be subject to the random company wide drug and alcohol screening.

The STARRT process is the corner stone of the Moretrench safety process. Pick ALL elements below that discribe this process.

A good STARRT will paint a mental picture for the employees working on the task, and will give anyone not familiar with the site a basic understanding of the type of work in the area.

The Safety Hazard Observation Wheel (SHOW) is a tool that Moretrench has developed to assist you in determining the hazards present.

If during the course of work any deviation occurs from the conditions identified in the Description of Task, Task Steps, Hazards, Recommended Corrective Action, as outlined on the STARRT form:

Stop-STARRT should not be confused with the Human Performance Improvement Tool, Stop When Unsure, which is a temporary stoppage of work by the individual performing the task to assure that they themselves are performing the task correctly.

How to use ‘Stop When Unsure’ check all that apply:

Always report every injury or incident IMMEDIATELY to your supervisor or a Safety Representative .

Seatbelts shall be worn at all times while operating or riding in a company vehicle or Mobile equipment. (NO SEAT BELT / NO RIDE)

All vehicles & mobile equipment shall have a daily inspection and the appropriate inspection form shall be completed. Report any defects to your supervisor.

Safety toed boots meeting the ANSI Z41.1 requirements must be worn on ALL worksites. ALL BOOTS SHALL BE LACE UP.

Damaged or defective electrical tools must be removed from service immediately for disposal or repair. Ensure that damaged or defective tools are tagged with “Danger Do Not Use” tags.