2A651 CDC Volume 1 (Q 107-124) Unit 6
-
When you receive an engine in your shop, you should check the applicable forms and then
-
Look for leaks.
-
Change the oil filter.
-
Inspect for missing parts.
-
Check the compressor inlet
-
Clear and acurate test for volume 1 cdc unit 6 (Q 107-125)
(96).webp "2A651 CDC Volume 1 (Q 107-124) Unit 6 - Quiz")
Quiz Preview
- 2.
Operating procedures and practices that,if not strictly observed, may result in damage to equipment are shown in the maintenance manuals in the form of
-
Notes.
-
Hints.
-
Warnings.
-
Cautions.
Correct Answer
A. Cautions.Explanation
The correct answer is "cautions". Operating procedures and practices that may result in equipment damage are typically shown in maintenance manuals in the form of cautions. Cautions serve as a warning or reminder to users to strictly observe certain actions or avoid certain behaviors to prevent potential damage to the equipment. They highlight specific risks or potential hazards that need to be taken into consideration during operation or maintenance activities.Rate this question:
-
- 3.
Preservation of a component being shipped is required when it is being returned to depot or stored for more than how many days?
-
15
-
30
-
60
Correct Answer
A. 30Explanation
When a component is being shipped and will be returned to the depot or stored for more than 30 days, it is necessary to preserve it. This is because components can be sensitive to environmental conditions such as temperature, humidity, and exposure to dust or contaminants. By preserving the component, it is protected from potential damage or degradation during transportation or storage, ensuring its functionality and longevity.Rate this question:
-
- 4.
The shroud-type cover consists of a buildup of how many layers of wrap?
-
2
-
4
-
3
-
5
Correct Answer
A. 3Explanation
The shroud-type cover consists of a buildup of three layers of wrap.Rate this question:
-
- 5.
Which TO covers the disposition of engines removed from aircraft involved in mishaps?
-
00-20-4.
-
2j-1-14.
-
2j-1-19.
-
33-1-37-1.
Correct Answer
A. 2j-1-19. -
- 6.
Which container does not require warehouse facilities?
-
Shroud.
-
Prefabricated.
-
Fiberglass reinforced plastic.
-
Flexible environment control.
Correct Answer
A. Fiberglass reinforced plastic.Explanation
Fiberglass reinforced plastic does not require warehouse facilities because it is a durable and lightweight material that can withstand various environmental conditions. Unlike other containers mentioned, such as shroud, prefabricated, and flexible environment control, fiberglass reinforced plastic can be stored outdoors without the need for a warehouse. This makes it a convenient option for storage and transportation purposes, as it does not require additional space or infrastructure.Rate this question:
-
- 7.
To release the internal air pressure in a shipping container/module, you must remove the
-
Parting surface nuts.
-
Parting surface bolts.
-
Filler valve on the side of the container.
-
Filler valve on the front of the container.
Correct Answer
A. Filler valve on the front of the container.Explanation
To release the internal air pressure in a shipping container/module, you must remove the filler valve on the front of the container. This is because the filler valve is the access point for air to enter or exit the container. By removing the filler valve, the air pressure inside the container can be equalized with the outside environment. The parting surface nuts and bolts are not related to releasing air pressure, and removing them would not have the desired effect.Rate this question:
-
- 8.
When removing the shipping container lid from the shipping container,how much are the turnlock fasteners turned?
-
1/4 turn.
-
1/2 turn.
-
1 turn.
-
2 turns.
Correct Answer
A. 1/4 turn.Explanation
When removing the shipping container lid, the turnlock fasteners are turned 1/4 of a turn. This means that the fasteners are rotated 90 degrees in order to release and remove the lid. This allows for easy and efficient opening of the shipping container without the need for excessive turning or complicated mechanisms.Rate this question:
-
- 9.
To determine whether an engine stored in a shipping container is serviceable or repairable,look on the
-
Side of the container.
-
Data plate on both halves of the container.
-
Top half on the right panel of the container.
-
Bottom half on the left panel of the container.
Correct Answer
A. Top half on the right panel of the container.Explanation
The correct answer is the top half on the right panel of the container. This is because the question is asking where to look for information about the engine's serviceability or repairability. The data plate on the top half of the right panel of the container is likely to contain this information. Looking on the side of the container or on both halves of the container may not provide the necessary information.Rate this question:
-
- 10.
Prior to removing a shipping container lid, what warning must be observed?
-
Ensure humidity indicator is blue.
-
Release all pressure before removing lid.
-
Lossen bolts in a staggered pattern to prevent warpage.
-
Ensure pressure is below 5 psi before lossening bolts.
Correct Answer
A. Release all pressure before removing lid.Explanation
Before removing a shipping container lid, it is important to release all pressure. This is necessary to ensure the safety of individuals handling the container and to prevent any potential accidents or injuries. By releasing the pressure, the risk of sudden release or explosion is minimized, making it safer to remove the lid.Rate this question:
-
- 11.
How many pins secure the adapters to the shipping container support?
-
2.
-
4.
-
8.
-
6.
Correct Answer
A. 4.Explanation
The correct answer is 4 because the question asks how many pins secure the adapters to the shipping container support. Therefore, the number of pins is 4.Rate this question:
-
- 12.
Engines inactive for over 180 days must have what accomplished?
-
Motor the engine to circulate the oil.
-
Inspect reservoirs to ensure they are full.
-
Visually inspect compressor for corrosion.
-
Preservation run and fuel system preservation.
Correct Answer
A. Preservation run and fuel system preservation.Explanation
Engines that have been inactive for over 180 days must undergo a preservation run and fuel system preservation. This is necessary to prevent any damage or deterioration that may occur due to prolonged inactivity. The preservation run involves running the engine at regular intervals to circulate the oil and ensure proper lubrication. Fuel system preservation involves taking measures to protect the fuel system from corrosion and contamination. Both of these steps are crucial in maintaining the engine's performance and prolonging its lifespan.Rate this question:
-
- 13.
To prepare the engine fuel system for service after depreservation, you must flush the system with
-
Oil.
-
Fuel
-
PD_680
-
Calibration fluid.
Correct Answer
A. Oil.Explanation
To prepare the engine fuel system for service after depreservation, it is necessary to flush the system with oil. This is because during the depreservation process, the fuel system may have accumulated debris, moisture, or contaminants that could potentially damage the engine if not properly removed. Flushing the system with oil helps to clean out any impurities and ensures that the fuel system is ready for use.Rate this question:
-
- 14.
When metal is attacked by chemical corrosion, it will start
-
Deep within the metal.
-
On the surface of the metal.
-
Throughout the metal all at once.
-
Just under the surface of the metal.
Correct Answer
A. On the surface of the metal.Explanation
When metal is attacked by chemical corrosion, it will start on the surface of the metal. This is because corrosion is a surface phenomenon where the metal reacts with the surrounding environment, such as oxygen or moisture, to form corrosion products. These products form a layer on the surface of the metal, gradually eating away at it and causing the corrosion to spread deeper into the metal over time. Therefore, the initial attack of chemical corrosion occurs on the surface of the metal.Rate this question:
-
- 15.
What is used to help remove moisture from an area where engines are stored?
-
CPC.
-
CPM.
-
Cobalt chloride.
-
Desiccants.
Correct Answer
A. Desiccants.Explanation
Desiccants are substances used to remove moisture from the air, preventing condensation and humidity. In an area where engines are stored, moisture can cause corrosion and damage to the engines. Desiccants, such as silica gel or activated charcoal, are commonly used to absorb moisture and maintain a dry environment. This helps to protect the engines and prevent any potential damage caused by moisture.Rate this question:
-
- 16.
On the personal maintenance platforms,the purpose of the platform safety lockpins is to
-
Prevent the platform from lowering while it is in use.
-
Prevent the platform from swaying while it is in use
-
Lock the base structure while the platform is in use.
-
Preventthe wheels from swiveling while it is in use.
Correct Answer
A. Prevent the platform from lowering while it is in use.Explanation
The purpose of the platform safety lockpins is to prevent the platform from lowering while it is in use. This is important for the safety of the individuals using the platform, as it ensures that the platform remains at a stable height and does not unexpectedly lower, potentially causing accidents or injuries. The lockpins provide a secure mechanism to hold the platform in place and prevent any downward movement while it is being used.Rate this question:
-
- 17.
Which maintenance platform can be adjusted from 3 to 7 feet?
-
B-1.
-
B-2.
-
B-4.
-
B-5.
Correct Answer
A. B-4.Explanation
The maintenance platform that can be adjusted from 3 to 7 feet is B-4.Rate this question:
-
- 18.
What info is found in part I of an AFTO form 244?
-
Item indentification
-
Supervisory review
-
Employee number blocks.
Correct Answer
A. Item indentificationExplanation
Part I of an AFTO Form 244 contains information about item identification. This section is used to identify the specific item or equipment that the form is being filled out for. It includes details such as the part number, serial number, and nomenclature of the item. This information is essential for accurately tracking and documenting maintenance and repair activities for the specific item.Rate this question:
-
Quiz Review Timeline (Updated): Jun 21, 2024 +
Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.
-
Current Version
-
Jun 21, 2024Quiz Edited by
ProProfs Editorial Team -
Nov 16, 2010Quiz Created by
Vison
Back to top