Ps:1 Router Table Safety Exam

Reviewed by Editorial Team
The ProProfs editorial team is comprised of experienced subject matter experts. They've collectively created over 10,000 quizzes and lessons, serving over 100 million users. Our team includes in-house content moderators and subject matter experts, as well as a global network of rigorously trained contributors. All adhere to our comprehensive editorial guidelines, ensuring the delivery of high-quality content.
Learn about Our Editorial Process
| By Pumpingstation
P
Pumpingstation
Community Contributor
Quizzes Created: 10 | Total Attempts: 27,068
| Attempts: 1,046
SettingsSettings
Please wait...
  • 1/10 Questions

    Check to see that the switch is in the off position before plugging the router into the outlet.

    • True
    • False
Please wait...
Ps:1 Router Table Safety Exam - Quiz
About This Quiz

This exam will test your knowledge of router table safety.
Note: This test is intended for use by members of Pumping Station: One, Chicago, only.

Quiz Preview

  • 2. 

    Never reach under the table while the router is running.

    • True

    • False

    Correct Answer
    A. True
    Explanation
    It is important to never reach under the table while the router is running because it can be extremely dangerous. The router has sharp blades that rotate at high speeds and can cause severe injuries if someone's hand or fingers get caught in them. Therefore, it is crucial to always turn off the router and wait for it to completely stop before reaching under the table to avoid any accidents.

    Rate this question:

  • 3. 

    You should wear a respirator when working on the router table?

    • True

    • False

    Correct Answer
    A. True
    Explanation
    It is important to wear a respirator when working on a router table because the machine produces a lot of dust and debris. These particles can be harmful if inhaled, causing respiratory problems or irritation. Wearing a respirator helps to filter out these particles and protect the person working on the router table.

    Rate this question:

  • 4. 

    Use a miter gauge and clamp for end grain shaping.

    • True

    • False

    Correct Answer
    A. True
    Explanation
    Using a miter gauge and clamp for end grain shaping is a correct and effective method. When shaping the end grain of a workpiece, it is important to have proper control and stability. A miter gauge helps in guiding the workpiece accurately and maintaining a consistent angle while shaping. Clamping the workpiece securely ensures that it does not move or shift during the shaping process, resulting in more precise and desired outcomes. Therefore, using a miter gauge and clamp for end grain shaping is a recommended approach.

    Rate this question:

  • 5. 

    Clamp a block of wood to the fence above the bit with clearance for your stock.

    • True

    • False

    Correct Answer
    A. True
    Explanation
    The statement suggests that one should clamp a block of wood to the fence above the bit with clearance for their stock. This is a correct statement as it is a common practice in woodworking to use a block of wood to provide support and stability to the stock being worked on. By clamping the block of wood to the fence above the bit, it ensures that the stock remains in place and prevents any potential accidents or mishaps while working with the tool.

    Rate this question:

  • 6. 

    The only foreign objects in the stock you need to be concerned with are nails.

    • True

    • False

    Correct Answer
    A. False
    Explanation
    The statement is false because it states that the only foreign objects in the stock to be concerned with are nails. This implies that there are no other foreign objects to be concerned with, which may not be true. There could be other foreign objects such as screws, staples, or other debris that can cause damage or harm. Therefore, it is important to be cautious and aware of all potential foreign objects in the stock, not just nails.

    Rate this question:

  • 7. 

    When shaping narrow stock (less than 3" wide) you should:

    • Keep your hands away from the bit.

    • Use feather boards and clamps.

    • Use a push block.

    • All of the above.

    Correct Answer
    A. All of the above.
    Explanation
    When shaping narrow stock, it is important to keep your hands away from the bit to avoid any accidents. Using feather boards and clamps helps to secure the stock in place, preventing any movement or slipping during the shaping process. Additionally, using a push block allows for better control and grip on the stock, ensuring a smooth and safe shaping experience. Therefore, all of the above options are necessary precautions to take when shaping narrow stock.

    Rate this question:

  • 8. 

    For control and safety how far should your hands and fingers be away from the revolving bit?

    • As far as practical with a minimum of 3".

    • You must always use a push stick on the router table.

    • As far as practical with a minimum of 6".

    • Never have your hands near the table.

    Correct Answer
    A. As far as practical with a minimum of 3".
    Explanation
    The correct answer states that for control and safety, your hands and fingers should be kept as far away from the revolving bit as possible, with a minimum distance of 3 inches. This ensures that there is enough distance to prevent any accidental contact with the bit, reducing the risk of injury. While it is important to use a push stick on the router table, this answer specifically addresses the distance requirement for hands and fingers.

    Rate this question:

  • 9. 

    The halves of so fence should touch the router bit so it will show the profile after the machine has been turned on.

    • True

    • False

    Correct Answer
    A. False
    Explanation
    The statement suggests that in order to see the profile of the fence after the router machine has been turned on, the halves of the fence should touch the router bit. However, this is not true. The profile of the fence can be seen even if the halves of the fence do not touch the router bit. The router bit will still shape the edges of the fence, regardless of whether the halves are touching it or not.

    Rate this question:

  • 10. 

    Freehand cuts are allowed when you remove the fence, if you use a starting pin and a bearing on the bit.

    • True

    • False

    Correct Answer
    A. True
    Explanation
    When removing the fence and using a starting pin and a bearing on the bit, freehand cuts are allowed. This means that the cuts can be made without the assistance or guidance of a fence, as long as the starting pin and bearing on the bit are used. Therefore, the statement is true.

    Rate this question:

Quiz Review Timeline (Updated): Mar 20, 2023 +

Our quizzes are rigorously reviewed, monitored and continuously updated by our expert board to maintain accuracy, relevance, and timeliness.

  • Current Version
  • Mar 20, 2023
    Quiz Edited by
    ProProfs Editorial Team
  • Apr 28, 2010
    Quiz Created by
    Pumpingstation

Related Topics

Recent Quizzes

Hand and Power Tool Quiz Hand and Power Tool Quiz
Review: Hammers, Ripping Bars, Nail Pullers, Chisels, Punches, and Screwdrivers Review: Hammers, Ripping Bars, Nail Pullers, Chisels, Punches, and Screwdrivers
Bay Path Tool Grinder Bay Path Tool Grinder
Bay Path Rules for Hand Tools Bay Path Rules for Hand Tools
Safety Tool Box Talk/Quiz 4.16.12 Safety Tool Box Talk/Quiz 4.16.12
WRMS Cut Off Saw Quiz WRMS Cut Off Saw Quiz

Popular Topics

+ Show more
Back to Top Back to top
Advertisement
×

Wait!
Here's an interesting quiz for you.

We have other quizzes matching your interest.