Pas X-tkj Komputer Dan Jaringan Dasar

The correct answer is Tang Crimping. The tool shown in the picture is used for crimping or compressing connectors onto the ends of network cables. It is commonly used in the installation and maintenance of Ethernet cables. The handles of the tool provide leverage to apply pressure and secure the connectors in place. This tool is essential for creating reliable and secure connections in networking applications.

The correct answer is "Topologi". Topologi refers to the design or layout of a computer network, including the arrangement of its nodes and connections. It determines how data flows within the network and how devices communicate with each other.

The bolded digits, 192.168.1.99, represent an IP address. An IP address is a unique numerical label assigned to each device connected to a computer network that uses the Internet Protocol for communication. It serves two main functions: identifying the host or network interface and providing the location of the host in the network. In this case, 192.168.1.99 is an example of an IP address given to a computer that will be connected to a network.

The given options are colors of wires in a UTP cable. The colors mentioned are Orange, White Orange, Green, Blue, and Black. All the mentioned colors are part of the UTP cable except for Black. Therefore, the correct answer is Black.

The correct answer is "Local Area Network". LAN stands for Local Area Network, which refers to a network that connects computers and devices within a limited area such as a home, office, or school. It allows for the sharing of resources, such as files and printers, and enables communication between connected devices.

not-available-via-ai

RJ45 is the correct answer because it is the most commonly used connector for UTP (Unshielded Twisted Pair) cables, which are commonly used for Ethernet networking. RJ45 connectors have 8 pins and are designed to connect to Ethernet ports on computers, routers, switches, and other networking devices. RJ11 connectors, on the other hand, are typically used for telephone connections and have 4 or 6 pins. RJ46, CR7, and RJ40 are not standard connector types and are not commonly used in networking.

The correct answer is Kabel Tester / LAN Tester. A Kabel Tester or LAN Tester is a tool specifically designed to test network cables, such as RJ45 or RJ11 cables, to determine if they are in good condition or not. It helps to identify any faults or issues in the cables, such as open circuits, short circuits, or incorrect wiring. By using a Kabel Tester / LAN Tester, network technicians can ensure that the cables are functioning properly and can troubleshoot any connectivity problems.

The correct answer is "Topologi Star." A star network topology is a computer network where all devices are connected to a central hub or switch. In this topology, the hub or switch acts as a packet controller, directing the flow of data packets. Each device in the network has a dedicated connection to the hub or switch, allowing for easy management and troubleshooting. This topology is commonly used in home and small office networks.

The correct answer is "Time to live". TTL stands for Time to Live in the ping command. It refers to the amount of time that a packet is allowed to live or exist in a network before it is discarded. This value is decremented by each router it passes through, and if it reaches zero, the packet is discarded.

A switch/hub is a device in a computer network that functions as a connector for data between multiple connections. It allows for the sharing of information between different devices on the network by receiving and transmitting data packets. This device helps to ensure efficient and effective communication between devices connected to the network.

The correct answer is Printer dan Monitor. Printer and Monitor are both examples of output devices in computer hardware. A printer is used to produce hard copies of documents or images, while a monitor is used to display visual output from the computer. These devices allow users to interact with and receive information from the computer system.

The correct command to view the IP configuration on a computer is "ipconfig".

The correct answer is "Input-Proses-Output". This is because hardware functions are categorized into three main parts: input, processing, and output. Input refers to the devices that allow users to enter data into the computer, such as keyboards or mice. Processing involves the manipulation and transformation of the input data by the computer's central processing unit (CPU). Finally, output refers to the devices that display or present the processed information, such as monitors or printers.

The correct answer is 54Mb/s. This is because IEEE 802.11g is a wireless networking standard that operates in the 2.4 GHz frequency range. It has a maximum data transfer rate of 54 Mbps, which is the theoretical maximum speed at which data can be transmitted over the network.

The correct answer is "Driver Lan Card" because a LAN card, also known as a network interface card (NIC), is a hardware component that allows a computer to connect to a local area network (LAN). In order for the LAN card to function properly, the appropriate driver software must be installed on the computer. This driver enables the operating system to communicate with the LAN card and establish a network connection. Therefore, the driver used to install a network device is the LAN card driver.

The correct answer is "ping google.com". This command is used to test the connectivity between the local network and a specific domain or IP address. By pinging google.com, we can check if our network connection is successfully reaching the Google domain.

Kabel Straight digunakan untuk menghubungkan 2 device yang berbeda dan memiliki cara pemasangan yang sama antara ujung satu dengan ujung yang lainnya.

The correct answer is "Menghubungkan Komputer dengan Switch". A straight cable is used to connect a computer to a switch. This type of cable allows for direct communication between the computer and the switch, enabling the computer to send and receive data through the switch to other devices on the network.

The given options are tools used in the making of UTP straight or crossover cables, except for "Card Rider." However, the term "Card Rider" is not commonly used in the context of cable making or networking. It is possible that the term is either misspelled or not relevant to the topic. Without further information, it is difficult to provide a specific explanation for the correct answer.

Dalam lingkungan LAN, server yang difungsikan sebagai data center sebaiknya dikelola dengan baik. Salah satu cara untuk melakukan manajemen yang efisien adalah dengan membagi ruang harddisk menjadi beberapa partisi. Dengan membagi harddisk menjadi partisi, pengguna dapat mengatur dan mengelola data dengan lebih baik sesuai dengan kebutuhan. Partisi juga memungkinkan pengguna untuk mengisolasi dan melindungi data yang berbeda, serta meningkatkan kinerja server dengan memisahkan data sistem operasi dan data aplikasi.

The "PING" command in a network is used to test the connectivity between two devices by sending ICMP echo request packets and receiving ICMP echo reply packets. It is commonly used to test network connectivity and troubleshoot network issues. However, it does not test the compatibility or suitability of a Network Interface Card (NIC). Therefore, the correct answer is "Menguji Kesesuaian NIC."

Crossover cables are used to directly connect two computers without the need for a network switch or hub. They have a different wiring configuration compared to straight cables, allowing the transmit and receive wires to be crossed over. This enables the computers to communicate and share data directly with each other. In contrast, straight cables are used to connect computers to network devices like switches or routers, while jumper, seri, and UTP are not directly related to connecting computers.

The correct answer is the combination of white orange – orange - white green – blue - white blue - green – white brown – brown. This combination follows the standard straight-through wiring sequence for Ethernet cables, where the orange and green pairs are used for transmitting data, and the blue and brown pairs are used for receiving data.

The correct answer is 100 HZ - 5 KHz. This range represents the frequency range for UTP cables. UTP cables are commonly used for Ethernet networks and telephone systems. They are designed to transmit signals in the frequency range of 100 Hz to 5 KHz, which is suitable for voice and data transmission over short distances.