Volume 5
Settings
- 1.The no flow/rupture alarm on the R-18 pumping unit will illuminate when the no flow/rupture pressure switch is activated for more than how many seconds?
- A.
5 Seconds
- B.
40 Seconds
- C.
20 Seconds
- D.
10 Seconds
- 2.What are the two positions of the throttle switch located on the R-18 pumping units hand held remote
- A.
Run and Idle
- B.
On off
- C.
On Idle
- D.
Off run
- 3.At what pressure will the pressure relief valve on the R-19 filter seperator unit open and send fuel to the sump tank?
- A.
150
- B.
175
- C.
200
- D.
225
- 4.The control valves will close if there is a communication loss between the R-20 multi-aircraft servicing unit and the lead pumping unit exceeding how many minutes
- A.
2
- B.
3
- C.
4
- D.
5
- 5.A steady red light on the battery status LED of the R20 multi-aircraft servicing platform indicates a battery
- A.
Charging
- B.
Charge Low
- C.
Disconnected
- D.
At middle capacity
- 6.With how many feet of communication wire is each R-20 Multi-aircraft servicing platform equipped?
- A.
1000 Feet
- B.
1500 feet
- C.
3000 feet
- D.
4500
- 7.
- A.
4 inch hard hose
- B.
6 inch hard hose
- C.
4 inch collapsible hose
- D.
6 inch collapsible hose
- 8.
- A.
1
- B.
2
- C.
3
- D.
4
- 9.When performing fuel servicing operations with the R-18 pumping unit, the throttle control should manually be set to what RPM setting?
- A.
1550 RPM
- B.
1850 RPM
- C.
1950 RPM
- D.
2250 RPM
- 10.When preparing the R-20 filter separator unit for shipment, drain all of the following components except the
- A.
Sump tank
- B.
Control valves
- C.
Micronic filter
- D.
Surge suppressors
- 11.
- A.
1
- B.
2
- C.
3
- D.
4
- 12.At what maximum rate can the R19 filter separator unit filter fuel
- A.
450 GPM
- B.
600 GPM
- C.
750 GPM
- D.
1200 GPM
- 13.At what maximum rate is the R20 multi aircraft servicing platform capable of supplying fuel through two hoses?
- A.
300
- B.
600
- C.
900
- D.
1200
- 14.
- A.
Jet Fuel and Gas
- B.
Jet Fuel and Diesel
- C.
Diesel Fuel and Gas
- D.
All
- 15.
- A.
400
- B.
500
- C.
600
- D.
700
- 16.At what flow rate can fuel be pumped through one 2 inch overwing nozzle on the R14 fuel servicing module?
- A.
100 GPM
- B.
200GPM
- C.
300GPM
- D.
400GPM
- 17.
- A.
Top Vent
- B.
Open Vent
- C.
Fill/Discharge Assembly
- D.
Tank vent pipe assembly
- 18.
- A.
75 Ft
- B.
100 FT
- C.
125 Ft
- D.
150 Ft
- 19.
- A.
Type of terrain
- B.
Weather Conditions
- C.
Amount of fuel being stored
- D.
Type of Aircraft to be serviced
- 20.Hearing protection must be worn when working within how many feet of the R-14C operation
- A.
25 Ft
- B.
50 Ft
- C.
75 Ft
- D.
100 Ft
- 21.
- A.
110 F
- B.
120 F
- C.
130 F
- D.
140 F
- 22.
- A.
10 PSi
- B.
20 PSI
- C.
30 PSi
- D.
40 PSi
- 23.When placed in the low mobility position, what is the maximum ramp angle the R-14C can negotiate.
- A.
10 deg
- B.
15 deg
- C.
20 deg
- D.
25 deg
- 24.
- A.
To fill the engine tank
- B.
To pump fuel from the drums
- C.
To fill the pumps priming unit
- D.
To pump fuel from operating tanks
- 25.When setting up the R22 how many sections of 25 foot hose should be used to connect the R22 to the FFU15E
- A.
2
- B.
3
- C.
4
- D.
5
- 26.After starting the R22 how long should the engine be allowed to idle before increasing the throttle setting
- A.
1 Min
- B.
3 Min
- C.
5 Min
- D.
6 Min
- 27.At what flow rate is the FFU15E filter separator capable of filter separator?
- A.
300 GPM
- B.
450 GPM
- C.
600 GPM
- D.
750 GPM
- 28.
- A.
6
- B.
12
- C.
15
- D.
30
- 29.
- A.
2000 Hours
- B.
3000 Hours
- C.
When the DP hits 15 or 2 years
- D.
When DP hits 20 or 3 years.
- 30.The canisters in the FFU15E filter separator are constucted of
- A.
Steel
- B.
Bronze
- C.
Copper
- D.
Aluminum
- 31.When setting up the FFU15E how should it be placed in relation to the dike wall?
- A.
25 feet in front of the dike wall
- B.
50 feet in front of the dike wall
- C.
25 feet in front of and centered on the dike wall
- D.
50 feet in front of and centered on the dike wall
- 32.When preparing the FFU15E for shipment complete all of the following procedures except
- A.
Drain all fuel from the unit
- B.
Remove the filter elements
- C.
Install dust caps on all fittings
- D.
Thoroughy clean the unit to remove dirt and debris
- 33.The TPI4T4A additive injector is capable of simultaneously injecting how many additives
- A.
2
- B.
3
- C.
4
- D.
6
- 34.
- A.
100 GPM
- B.
250 GPM
- C.
600 GPM
- D.
No meter is installed
- 35.When setting up the TPI4T4A where should the corrosion inhibitor and static dissipater additive tanks be placed
- A.
On top of the injector Cage
- B.
Underneath the Injector cage
- C.
On top of one another on the left side of the injector cage
- D.
On top of one nother on the right side of the injector cage
- 36.When must the injectors on the TPI4T4A additive injector be purged of all additives
- A.
Daily
- B.
Every 48 hours
- C.
When changing from one type of additive to another
- D.
When the unit will be inoperative for more then 72 hours
- 37.
- A.
Safety Goggles
- B.
Rubber gloves
- C.
Safety goggles and rubber gloves
- D.
Apron safety goggles and rubber gloves
- 38.All of the following things should be considered before starting a calibration run with the TPI4T4A additive injector except what
- A.
Amount of additive will be injected
- B.
Flow rate through the unit
- C.
Amount of additive to be collected
- D.
Lenght of time for calibrating
- 39.The secondary purpose of the pmu27m self priming pump is refueling
- A.
Large aircraft
- B.
Small aircraft
- C.
Ground equipment
- D.
Emergency generators
- 40.
- A.
50GPM
- B.
100GPM
- C.
150GPM
- D.
200GPM
- 41.
- A.
3
- B.
9
- C.
15
- D.
24
- 42.To facilitate priming the PMU27M self priming pump is provided with a priming
- A.
Stem
- B.
Hose
- C.
Valve
- D.
Coupler
- 43.The 117 MRSP kit is quipped with how many 500 Gallon sealed drums?
- A.
2
- B.
3
- C.
4
- D.
6
- 44.When preparing the PMU27M for shipment complete all of the following steps except
- A.
Drain the filter separator
- B.
Thoroughly clean the unit
- C.
Secure all hoses and adapters to the trailer frame
- D.
Remove the filter elements from the filter separator
- 45.
- A.
6
- B.
8
- C.
10
- D.
12
- 46.
- A.
Daily
- B.
Weekly
- C.
Monthly
- D.
Semi annually
- 47.The water slug valve check on the FFU15E must be performed
- A.
Daily
- B.
Weekly
- C.
Monthly
- D.
Semiannually
- 48.The PMU27M hoses are inspected daily for all of the following except
- A.
Cracking
- B.
Worn spots
- C.
Deterioration
- D.
Loose mounting
- 49.The fuel Filter element on the PMU 27M should be changed every
- A.
250 hours or 3 month
- B.
500 hours or 3 months
- C.
1000 hours or more often as required
- D.
2000 hours or more often as required
- 50.At a minimum the R18 pumping unit oil filer should be changed every
- A.
250 hours of operation or semiannually
- B.
500 horus of opeartion or semi annually
- C.
250 hours or annualy
- D.
500 hours or annually
- 51.
- A.
30 Psi
- B.
65 Psi
- C.
75 Psi
- D.
100 Psi
- 52.
- A.
Daily
- B.
Weekly
- C.
Monthly
- D.
Quarterly
- 53.All of the following conditions require replacement of filter elements on the R19 filter separator unit except
- A.
16 psi on DP gauge
- B.
Filter separator vessel performance is questionable
- C.
22 Psi on DP guage
- D.
Elements in use for 36 months
- 54.When performing fuels mobility site planning what agencry should be your first source of INfo for infrastructure availability?
- A.
MAJCOM
- B.
Defense Mapping Agency
- C.
DLA
- D.
DESC
- 55.
- A.
JP5
- B.
Jet A
- C.
Jet A 1
- D.
Jet B
- 56.MRSP kits contain sufficient stock to allow support in a deployed location for how many days before resupply is necessary?
- A.
30 Days
- B.
60 Days
- C.
90 Days
- D.
180 Days
- 57.Accountability for a transferred MRSP kit temporary rests with the
- A.
Home LRS customer Service element
- B.
Expeditionary LRS at the forward locaiton
- C.
Accountable Officer
- D.
Using organization
- 58.
- A.
Fume detector
- B.
Crossover manifold
- C.
Flexible exhaust Pipe
- D.
Automatic vapor eliminator
- 59.
- A.
200 GPM
- B.
300 GPM
- C.
400 GPM
- D.
600 GPM
- 60.
- A.
Fill Assembly
- B.
Drain Assembly
- C.
Vertical vent pipe
- D.
Discharge assembly
- 61.When positioning 50000 gallon fuel bladders inside a diked area, how far apart must the tanks be from each other?
- A.
3 feet
- B.
4 feet
- C.
6 feet
- D.
8 feet
- 62.Sealing clamps used for emergency repair of fuel bladder comes in all sized except
- A.
3 inch
- B.
5 inch
- C.
6.5 inch
- D.
7.5 inch
- 63.THe forward area manifold cart is capable of servicing up to how many receiver aircraft at one time?
- A.
2
- B.
3
- C.
4
- D.
6
- 64.The forward area manifold cart engine can run on all of the following types of fuel except
- A.
JP5
- B.
JP8
- C.
Gasoline
- D.
Diesel
- 65.For air shipment the inner tanks of empty cryotainers are pressurized with dry nitrogen gas at a positive pressure of
- A.
10-15 psig
- B.
15-25 psig
- C.
25-30 psig
- D.
30-40 psig
- 66.Fuels personnel identify the tank vent valve by using a locally manufactured
- A.
Bronze Disc
- B.
Adhessive label
- C.
Wooden Placard
- D.
Round aluminum disc
- 67.During air shipment the cryotainer inner tank pressure should not exceed what manixum psi reading?
- A.
35 PSI
- B.
40 psi
- C.
50 psi
- D.
55 psi
- 68.
- A.
45 psi
- B.
75 psi
- C.
90 psi
- D.
150 psi
Back to top