Set B UREs Volume 1
(12).webp "Set B UREs Volume 1 - Quiz")
- 1.
Before using an electric drill, what is the first thing you should do ?
- A.
Make sure the diameter of the hole to be drilled is with in the capacity of the drill
- B.
Connect the drill to the power source
- C.
Ask a coworker for assistance
- D.
Insert the Chuck key
Correct Answer
A. Make sure the diameter of the hole to be drilled is with in the capacity of the drillExplanation
Before using an electric drill, it is important to make sure that the diameter of the hole to be drilled is within the capacity of the drill. This is necessary to ensure that the drill can handle the size of the hole and prevent any damage or accidents from occurring. It is important to check this before connecting the drill to the power source or inserting the chuck key. Asking a coworker for assistance may be helpful, but it is not the first thing that should be done.Rate this question:
-
- 2.
The purpose of using cutting lubricant during most drilling operations is to increase the
- A.
Life of the drill only
- B.
Speed of drilling only
- C.
Frictional heat during drilling
- D.
Drilling speed and the drill bit life
Correct Answer
D. Drilling speed and the drill bit lifeExplanation
The purpose of using cutting lubricant during most drilling operations is to increase the drilling speed and the drill bit life. Cutting lubricant helps to reduce friction between the drill bit and the material being drilled, which in turn reduces heat and wear on the drill bit. By reducing friction and heat, the lubricant allows the drill bit to operate at a higher speed without overheating or wearing down too quickly, thus improving both the drilling speed and the overall lifespan of the drill bit.Rate this question:
-
- 3.
Which minimum articles of safety gear must be worn when using a bench grinder?
- A.
Apron and gloves
- B.
Eye and face protection
- C.
Gloves and steel toed boots
- D.
Safety glasses and long sleeve shirt
Correct Answer
B. Eye and face protectionExplanation
When using a bench grinder, it is necessary to wear eye and face protection. This is because the grinder can produce sparks, debris, and particles that can cause harm to the eyes and face. Eye and face protection, such as safety glasses or a face shield, can help prevent injuries and ensure the safety of the person using the grinder. Wearing just an apron and gloves, gloves and steel-toed boots, or safety glasses and a long sleeve shirt would not provide adequate protection for the eyes and face.Rate this question:
-
- 4.
An electric saw blade must be operating at what speed before it contacts the material been cut?
- A.
Full
- B.
Low
- C.
Moderate
- D.
Accelerated
Correct Answer
A. FullExplanation
Before an electric saw blade contacts the material being cut, it should be operating at full speed. This ensures that the blade is able to cut through the material effectively and efficiently. Operating at a lower speed may cause the blade to get stuck or result in a poor quality cut. Moderate or accelerated speeds may also not be sufficient to cut through certain materials. Therefore, full speed is the correct answer in order to achieve optimal cutting performance.Rate this question:
-
- 5.
How many pounds per square inch of clean, dry air is required at the tool end of the air hose to ensure the tool is operating safely and efficiently?
- A.
60
- B.
90
- C.
110
- D.
125
Correct Answer
B. 90Explanation
To ensure that a tool is operating safely and efficiently, it requires a certain amount of pressure from the air hose. In this case, the correct answer is 90 pounds per square inch (psi). This pressure is sufficient to power most tools effectively without causing any damage or inefficiency. Higher pressures may lead to excessive wear and tear on the tool, while lower pressures may result in reduced performance. Therefore, maintaining a pressure of 90 psi at the tool end of the air hose is crucial for safe and efficient tool operation.Rate this question:
-
- 6.
What condition would prevent an operator from applying power to a hoist or other powered lifting device?
- A.
An AF Form 979 is attached the unit
- B.
Potential for lightning within 15 miles of the area
- C.
Procedures are not covered in detail in the owners manual
- D.
The unit is tagged with a DD form 1574–1, Condition Code A
Correct Answer
A. An AF Form 979 is attached the unit -
- 7.
What should be worn anytime there is a potential for injury from overhead objects during a lifting operation?
- A.
Kevlar
- B.
Safety goggles
- C.
Leather gloves
- D.
Protective helmet
Correct Answer
D. Protective helmetExplanation
A protective helmet should be worn anytime there is a potential for injury from overhead objects during a lifting operation. This is because a protective helmet provides a barrier of protection for the head, reducing the risk of head injuries caused by falling or flying objects. It is important to wear a helmet to ensure the safety and well-being of the individual performing the lifting operation.Rate this question:
-
- 8.
What is the most common type of lifting sling used in the munitions career field?
- A.
Chain assembly
- B.
Web strapping
- C.
Metal mesh
- D.
Wire rope
Correct Answer
D. Wire ropeExplanation
Wire rope is the most common type of lifting sling used in the munitions career field. This is because wire ropes are strong, durable, and resistant to abrasion and heat. They can handle heavy loads and provide stability and security when lifting and moving munitions. Wire ropes are also flexible and can be easily adjusted to fit different lifting situations. Overall, wire ropes are the preferred choice for lifting slings in the munitions career field due to their reliability and strength.Rate this question:
-
- 9.
The following are all good safety practices to follow when using a lifting sling except
- A.
Standing clear of the attached load
- B.
Padding any sharp corners the sling may come in contact with
- C.
Keeping your hands and fingers from between the sling and the load
- D.
Inspecting the sling by passing your bare hand over the body of the sling
Correct Answer
D. Inspecting the sling by passing your bare hand over the body of the slingExplanation
Inspecting the sling by passing your bare hand over the body of the sling is not a good safety practice to follow when using a lifting sling. This is because passing your bare hand over the body of the sling can expose your hand to potential hazards such as sharp edges, rough surfaces, or contaminants on the sling. It is important to inspect the sling visually and use appropriate tools or gloves to check for any damages, wear, or defects before using it.Rate this question:
-
- 10.
The annunciators display on the fluke 8025 – series multimeter are used to distinguish among
- A.
Ohms, Milliohms, Kilohms
- B.
Ohms, Kilohms, Megohms
- C.
Amps, Ohms, Millivolts
- D.
Ohms, Volts, Amps
Correct Answer
B. Ohms, Kilohms, MegohmsExplanation
The annunciators display on the Fluke 8025 - series multimeter are used to distinguish between different units of resistance. The correct answer is Ohms, Kilohms, Megohms. This means that the multimeter can measure resistance in Ohms (Ω), Kilohms (KΩ), and Megohms (MΩ). The annunciators on the display will indicate which unit is being measured, allowing the user to easily interpret the resistance values.Rate this question:
-
- 11.
What are two operational modes of the fluke 8025 – series multimeter?
- A.
Alternating current and direct current
- B.
Range and hold
- C.
Auto and manual
- D.
Continuous and momentary
Correct Answer
B. Range and holdExplanation
The operational modes of the Fluke 8025 - series multimeter are "Range" and "Hold". The "Range" mode allows the user to select the appropriate measurement range for the input signal, ensuring accurate readings. The "Hold" mode allows the user to freeze the displayed reading on the screen, making it easier to record or analyze the measurement.Rate this question:
-
- 12.
The steering system on the MHU – 141/M trailer has a turning radius of how many inches?
- A.
90
- B.
200
- C.
400
- D.
600
Correct Answer
B. 200Explanation
The correct answer is 200. The steering system on the MHU-141/M trailer has a turning radius of 200 inches.Rate this question:
-
- 13.
When the MHU – 141 trailer is loaded or towed with the hinged deck panels open, what should be done?
- A.
The deck panels supports must be properly positioned and locked in place with quick release pins.
- B.
The deck panels supports must be properly positioned and held in place with a tiedown strap.
- C.
Bomb jocks must be positioned to the deck panels and locked in place with cotter pins.
- D.
Close and lock the two deck panels; the trailer cannot be towed in this configuration .
Correct Answer
A. The deck panels supports must be properly positioned and locked in place with quick release pins.Explanation
When the MHU – 141 trailer is loaded or towed with the hinged deck panels open, the deck panel supports must be properly positioned and locked in place with quick release pins. This is important to ensure the stability and safety of the trailer during transportation. The quick release pins provide a secure and reliable locking mechanism for the deck panels, preventing them from moving or falling open while the trailer is in motion.Rate this question:
-
- 14.
What is the maximum load capacity of the MHU – 110/M trailer?
- A.
5,000 pounds
- B.
5,500 pounds
- C.
15,000 pounds
- D.
20,000 pounds
Correct Answer
C. 15,000 poundsExplanation
The maximum load capacity of the MHU-110/M trailer is 15,000 pounds.Rate this question:
-
- 15.
The parking brake on the MHU 110/M is applied by
- A.
Pulling either one of two hand lever is located on each side of the front of the trailer.
- B.
Pulling either one of two handle lever is located on each side of the rear of trailer.
- C.
Pulling the center hand lever located in the front of the trailer.
- D.
Pulling the surge brake located on the tongue of the trailer.
Correct Answer
A. Pulling either one of two hand lever is located on each side of the front of the trailer.Explanation
The correct answer is pulling either one of two hand levers located on each side of the front of the trailer. This means that the parking brake on the MHU 110/M is engaged by pulling one of the two hand levers, which are situated on either side of the front of the trailer.Rate this question:
-
- 16.
How many openings, hinged door panels, are on the deck of the MHU – 226 trailer?
- A.
1
- B.
2
- C.
3
- D.
4
Correct Answer
C. 3Explanation
The MHU-226 trailer has three hinged door panels on its deck.Rate this question:
-
- 17.
What type of steering aids the MHU – 226 and a tighter steering radius?
- A.
Rack and pinion
- B.
Power recirculating ball
- C.
Front wheel automotive type
- D.
Four wheel double Ackerman
Correct Answer
D. Four wheel double Ackerman -
- 18.
After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets to the trailer?
- A.
Steel chains only
- B.
Wire ropes and slack adjusters
- C.
Would bracing and tiedown straps
- D.
MB–1 chain assemblies and/or tie–down straps
Correct Answer
D. MB–1 chain assemblies and/or tie–down strapsExplanation
MB-1 chain assemblies and/or tie-down straps can be used to secure the pallets to the trailer.Rate this question:
-
- 19.
What kind of movement supports on-base activities to or from the flightline ?
- A.
Hazardous cargo
- B.
Operational
- C.
Logistical
- D.
Intra-base
Correct Answer
B. OperationalExplanation
Operational movement supports on-base activities to or from the flightline. This type of movement involves the transportation of personnel, equipment, and supplies necessary for the daily operations and functioning of the base. It includes activities such as the movement of aircraft, ground vehicles, and maintenance personnel to and from the flightline. Operational movement is crucial for the smooth functioning of the base and ensuring that all necessary resources are available for flight operations.Rate this question:
-
- 20.
What munitions item is not loaded into transport modules by munitions personnel?
- A.
BDU – 33
- B.
MK 106
- C.
ALE – 50
- D.
20 MM
Correct Answer
D. 20 MMExplanation
Munitions personnel do not load 20 MM munitions into transport modules.Rate this question:
-
- 21.
What transport module used for decoy munitions has a maximum capacity of 30 magazines?
- A.
BDU – 33
- B.
ALE – 40
- C.
ALE – 50
- D.
20 MM
Correct Answer
C. ALE – 50Explanation
The ALE-50 is the transport module used for decoy munitions with a maximum capacity of 30 magazines.Rate this question:
-
- 22.
How often should the locking devices on the doors of munitions transport modules be checked?
- A.
At the beginning and end of each shift
- B.
During initial pre-check of the trailer only
- C.
After loading, unloading, and periodically between stops
- D.
After loading, unloading, and every 10 minutes when transporting
Correct Answer
C. After loading, unloading, and periodically between stopsExplanation
The correct answer is "After loading, unloading, and periodically between stops." This is because checking the locking devices on the doors of munitions transport modules after loading and unloading ensures that they are secure and properly locked. Additionally, checking periodically between stops ensures that the doors remain secure throughout the transportation process. Regular checks are necessary to prevent any unauthorized access or tampering with the munitions inside the modules.Rate this question:
-
- 23.
The purpose of the transport beam beneath the lift arm assembly on the MJ-1 - series lift truck is to
- A.
Provide added stability and to decrease hydraulic pressure from the lift boom when caring maximum capacity loads over long distances.
- B.
Provide added support and to relieve hydraulic pressure from the left arms when caring loads for long distances.
- C.
Relieve excess pneumatic pressure from the lift boom when the lift truck is parked.
- D.
Relieve access hydraulic pressure from the lift boom when the lift truck is parked.
Correct Answer
A. Provide added stability and to decrease hydraulic pressure from the lift boom when caring maximum capacity loads over long distances.Explanation
The transport beam beneath the lift arm assembly on the MJ-1 series lift truck is designed to provide added stability and reduce hydraulic pressure from the lift boom when carrying maximum capacity loads over long distances. This helps to prevent tipping or instability during transport and ensures smooth and safe operation of the lift truck.Rate this question:
-
- 24.
What is the lifting capacity of the MJ–1 series lift truck?
- A.
3000 pounds
- B.
3500 pounds
- C.
6000 pounds
- D.
6500 pounds
Correct Answer
A. 3000 poundsExplanation
The lifting capacity of the MJ-1 series lift truck is 3000 pounds.Rate this question:
-
- 25.
What is the lifting capacity of the MHU – 83 series lift truck?
- A.
3000 pounds
- B.
3500 pounds
- C.
6000 pounds
- D.
7000 pounds
Correct Answer
D. 7000 poundsExplanation
The lifting capacity of the MHU-83 series lift truck is 7000 pounds.Rate this question:
-
- 26.
When using the MHU – 83 series lift truck with fork adapters, you immediately
- A.
Reduce its lifting capacity by 800 pounds
- B.
Reduce its lifting capacity by 1000 pounds
- C.
Increase its lifting capacity by 800 pounds
- D.
Increase its lifting capacity by 1000 pounds
Correct Answer
B. Reduce its lifting capacity by 1000 poundsExplanation
When using the MHU-83 series lift truck with fork adapters, the lifting capacity is reduced by 1000 pounds. This means that the lift truck can lift 1000 pounds less than its original lifting capacity when the fork adapters are attached.Rate this question:
-
- 27.
What happens when you release the accelerator pedal on a vehicle driven with a hydrostatic transmission?
- A.
The lift truck stops immediately.
- B.
The unit rolls until it’s inertia is spent.
- C.
The unit coast to a stop very quickly.
- D.
The transmission automatically drops to a lower gear.
Correct Answer
C. The unit coast to a stop very quickly.Explanation
When you release the accelerator pedal on a vehicle driven with a hydrostatic transmission, the unit will coast to a stop very quickly. This is because a hydrostatic transmission uses fluid pressure to transmit power, and when the accelerator pedal is released, the fluid pressure decreases, causing the vehicle to lose momentum and come to a stop rapidly.Rate this question:
-
- 28.
What is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU – 83 series lift truck?
- A.
Very labor-intensive.
- B.
Difficult to make final adjustments to the table.
- C.
Extremely slow way to build hydraulic pressure.
- D.
Possible to damage hydraulic system due to overpressurization.
Correct Answer
C. Extremely slow way to build hydraulic pressure.Explanation
The primary drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU-83 series lift truck is that it is an extremely slow way to build hydraulic pressure. This means that it would take a significant amount of time and effort to reach the desired level of pressure, which can be inefficient and time-consuming.Rate this question:
-
- 29.
How is the yaw positioning from the cradle or boom controls of an MJ-1 lift truck adjusted?
- A.
Pneumatically.
- B.
Hydraulically.
- C.
Electrically.
- D.
Manually.
Correct Answer
D. Manually.Explanation
The yaw positioning from the cradle or boom controls of an MJ-1 lift truck is adjusted manually. This means that the operator of the lift truck would need to physically adjust the yaw positioning using their own strength and control.Rate this question:
-
- 30.
What category or categories are Air Force air compressors classified?
- A.
By application.
- B.
High or low pressure.
- C.
Self-propelled or towed.
- D.
Powered or non-powered support equipment.
Correct Answer
B. High or low pressure.Explanation
Air Force air compressors are classified based on their pressure levels, either high or low. This classification helps in determining the specific use and application of the air compressors within the Air Force.Rate this question:
-
- 31.
The primary difference between a bobtail and a pick up truck is the
- A.
Bobtail provides a smoother ride.
- B.
Bob tail is designed for long distance towing.
- C.
Bobtail’s back and is shortened by about one half.
- D.
Bobtail’s front wheel base is smaller for better turning radius.
Correct Answer
C. Bobtail’s back and is shortened by about one half.Explanation
The primary difference between a bobtail and a pick up truck is that the bobtail's back is shortened by about one half. This means that the cargo area of the bobtail is smaller compared to a pick up truck. This difference in size can affect the overall maneuverability and capacity of the vehicle.Rate this question:
-
- 32.
What is the purpose behind good operator maintenance of all assigned vehicles?
- A.
Mission readiness.
- B.
Reduce maintenance costs.
- C.
Maintain vehicle serviceability at reduced cost.
- D.
Make sure vehicles are serviceable and in good condition.
Correct Answer
C. Maintain vehicle serviceability at reduced cost.Explanation
Maintaining vehicle serviceability at a reduced cost is important because it ensures that the vehicles are in good condition and ready to be used for their intended purpose. By properly maintaining the vehicles, the need for costly repairs and replacements can be minimized, resulting in reduced maintenance costs. This also helps to ensure that the vehicles are always in a state of readiness, ready to be deployed whenever needed.Rate this question:
-
- 33.
What is the maximum amount of pounds the MB-4 aircraft towing tractor can tow and push?
- A.
120,000 pounds
- B.
130,000 pounds
- C.
140,000 pounds
- D.
150,000 pounds
Correct Answer
C. 140,000 poundsExplanation
The MB-4 aircraft towing tractor is capable of towing and pushing a maximum weight of 140,000 pounds.Rate this question:
-
- 34.
Pintle safety locking pins must remain attached to the pintle assembly
- A.
To prevent an unsecured pin from coming out and getting lost
- B.
To ensure it is available if needed
- C.
By a non-conductive material
- D.
By a bungee cord
Correct Answer
A. To prevent an unsecured pin from coming out and getting lostExplanation
The correct answer is to prevent an unsecured pin from coming out and getting lost. This is important because if the pin is not securely attached to the pintle assembly, it can easily become dislodged and lost. This can pose a safety risk as the pintle assembly may become unstable or fail without the pin in place. By keeping the pin attached, it ensures that it remains in its proper position and reduces the risk of accidents or damage occurring.Rate this question:
-
- 35.
What gear range should be selected in a tractor with an automatic transmission while going downhill?
- A.
Neutral
- B.
Low range
- C.
High range
- D.
Any range is acceptable.
Correct Answer
B. Low rangeExplanation
When going downhill in a tractor with an automatic transmission, selecting the low range is the correct choice. This is because the low range provides more torque and engine braking, which helps to control the speed of the tractor and prevent it from gaining too much momentum. The low range also allows for better control and maneuverability on steep slopes, ensuring the tractor can safely navigate downhill terrain.Rate this question:
-
- 36.
What is the purpose of the trailer hand valve (Johnson bar) ?
- A.
Test the trailer brakes
- B.
Slow the tractor on wet pavement
- C.
Slow the tractor to prevent skidding
- D.
To draft the trailer into the right trajectory when you make a turn to sharp.
Correct Answer
A. Test the trailer brakesExplanation
The purpose of the trailer hand valve (Johnson bar) is to test the trailer brakes. This valve allows the driver to manually apply the brakes on the trailer to ensure they are functioning properly. By using the trailer hand valve, the driver can test the brakes without needing to use the tractor's brakes. This is important for safety and to ensure that the trailer can be stopped effectively when necessary.Rate this question:
-
- 37.
What are hose couplers (glad hands) used for on contractor/trailer combinations?
- A.
To connect the service and emergency brake airlines from the tractor to the trailer
- B.
To connect the service brake airline with the emergency brake airline
- C.
To secure the airlines to the tractor to avoid them from dragon
- D.
To join sections of service brake airlines on the trailer
Correct Answer
A. To connect the service and emergency brake airlines from the tractor to the trailerExplanation
Hose couplers, also known as glad hands, are used to connect the service and emergency brake airlines from the tractor to the trailer. This allows for the transfer of air pressure between the two vehicles, enabling the driver to control the trailer's brakes from the tractor.Rate this question:
-
- 38.
Which procedure is not a consideration for backing a tractor/trailer combination ?
- A.
Use a spotter.
- B.
Use mirrors on both sides.
- C.
Turn toward the drivers side.
- D.
Turn toward the passengers side.
Correct Answer
D. Turn toward the passengers side.Explanation
The procedure of turning toward the passengers side is not a consideration for backing a tractor/trailer combination. When backing a tractor/trailer combination, it is important to use a spotter to guide the driver, as well as mirrors on both sides to ensure proper visibility. Turning toward the drivers side is also necessary to safely maneuver the trailer while backing. However, turning toward the passengers side is not a recommended procedure and is not necessary for backing a tractor/trailer combination.Rate this question:
-
- 39.
What is the maximum depth of water you may drive a rough-terrain forklift through?
- A.
3 feet.
- B.
5 feet.
- C.
7 feet.
- D.
8 feet.
Correct Answer
B. 5 feet.Explanation
A rough-terrain forklift is specifically designed to handle uneven and rough surfaces, including water. However, there are limits to the depth of water it can safely navigate. The maximum depth of water you may drive a rough-terrain forklift through is 5 feet. This is likely due to the fact that exceeding this depth could pose a risk to the forklift's stability and potentially damage its electrical components.Rate this question:
-
- 40.
What is the most beneficial attribute of using the swingmast forklift?
- A.
Operates inside due to its quiet running engine.
- B.
Allows you to maximize the available storage space.
- C.
Moves bigger assets quickly due to his increased weight limitation.
- D.
Empties international shipping organization (ISO) containers quickly.
Correct Answer
B. Allows you to maximize the available storage space.Explanation
The most beneficial attribute of using the swingmast forklift is that it allows you to maximize the available storage space.Rate this question:
-
- 41.
With the forks level, what is the maximum reach of the variable–reach forklift?
- A.
15 feet
- B.
16 feet
- C.
20 feet
- D.
22 feet
Correct Answer
D. 22 feetExplanation
The maximum reach of the variable-reach forklift is 22 feet. This means that the forklift can extend its forks up to a distance of 22 feet, allowing it to reach and lift objects that are positioned high off the ground. This extended reach capability is beneficial for tasks that require lifting and moving heavy loads at elevated heights, such as stacking items on high shelves or loading/unloading goods from tall trucks or containers.Rate this question:
-
- 42.
What USAF gun system is loaded and unloaded by the linkless ammunition loading system (LALS)?
- A.
The GAU – 2B/A, 7.26 MM machine gun
- B.
The M197, 20 MM Gatling gun
- C.
The GAU-8A, 30 MM canon
- D.
The M61A1, 20 mm cannon
Correct Answer
D. The M61A1, 20 mm cannonExplanation
The correct answer is the M61A1, 20 mm cannon. This gun system is loaded and unloaded by the linkless ammunition loading system (LALS).Rate this question:
-
- 43.
Which weapon replaceable assembly of the linkless ammunition loading system (LALS) has no moving parts?
- A.
Conveyor.
- B.
Transfer unit.
- C.
Trailer chassis.
- D.
Storage container.
Correct Answer
D. Storage container.Explanation
The storage container in the linkless ammunition loading system (LALS) has no moving parts. This means that it is a stationary component of the system and does not require any mechanical movement to function. The storage container is responsible for holding the ammunition before it is loaded into the weapon, and it does not need any moving parts to perform this task effectively.Rate this question:
-
- 44.
Which subassembly of the universal ammunition loading system (UALS) houses a remaining indicator window that provides the means to visually determine the approximate number of rounds in the unit?
- A.
Inner drum.
- B.
Outer drum.
- C.
Middle drum.
- D.
Interface unit.
Correct Answer
B. Outer drum.Explanation
The correct answer is outer drum. The outer drum of the universal ammunition loading system (UALS) houses a remaining indicator window that allows users to visually determine the approximate number of rounds in the unit. This indicator window provides a convenient way to keep track of the ammunition levels during loading operations.Rate this question:
-
- 45.
Which subassembly of the universal ammunition loading system (UALS) provides the means to load live rounds into the aircraft gun system?
- A.
Inner drum.
- B.
Outer drum.
- C.
Interface unit.
- D.
Ammunition conveyor.
Correct Answer
C. Interface unit.Explanation
The interface unit of the universal ammunition loading system (UALS) is responsible for providing the means to load live rounds into the aircraft gun system. It serves as the connection between the ammunition conveyor and the gun system, allowing for the safe and efficient transfer of live rounds. The interface unit ensures that the ammunition is properly aligned and secured before it is loaded into the gun system, minimizing the risk of accidents or malfunctions during the loading process.Rate this question:
-
- 46.
Which subassembly of the universal ammunition loading system (UALS) provides the power that cycles the rounds through the system?
- A.
Inner drum.
- B.
Outer drum.
- C.
Interface unit.
- D.
Pneumatic regulator.
Correct Answer
D. Pneumatic regulator.Explanation
The pneumatic regulator is responsible for providing the power that cycles the rounds through the system in the universal ammunition loading system (UALS). It regulates the air pressure and controls the flow of compressed air, which is used to move the rounds from one part of the system to another. The inner drum, outer drum, and interface unit do not provide the power for this function.Rate this question:
-
- 47.
How often should a universal ammunition loading system (UALS) replenisher assemblies be inspected?
- A.
Every 30 days when in use and annually when in storage.
- B.
Every 45 days when in use and and annually when in storage.
- C.
Every 60 days when in use and annually win in storage.
- D.
Every 90 days when in use an annual he went in storage.
Correct Answer
A. Every 30 days when in use and annually when in storage.Explanation
A universal ammunition loading system (UALS) is a complex piece of equipment that is used for loading ammunition onto various types of weapons. Regular inspections are necessary to ensure that the system is functioning properly and to identify any potential issues or maintenance needs. The answer "Every 30 days when in use and annually when in storage" suggests that the UALS should be inspected more frequently when it is being actively used, as there is a higher chance of wear and tear or damage occurring during this time. Additionally, an annual inspection when in storage ensures that the system remains in good condition even when not in use.Rate this question:
-
- 48.
Which subassembly on the universal ammunition loading system (UALS) replenisher assembly prevents accidentally loading a spent cartridge into the loader assembly?
- A.
Drive assembly.
- B.
Delinker loader unit.
- C.
Empty space preclusion device.
- D.
Rigid ammunition chute assembly
Correct Answer
C. Empty space preclusion device.Explanation
The empty space preclusion device prevents accidentally loading a spent cartridge into the loader assembly. This device ensures that only live ammunition is loaded by blocking any empty space in the loader assembly, preventing the insertion of spent cartridges.Rate this question:
-
- 49.
Which tool can initiate cycling ammunition through the universal ammunition system (UALS) replenisher manually?
- A.
1/4 inch speed wrench.
- B.
1/2 inch speed wrench.
- C.
1/4 inch ratchet and socket.
- D.
1/2 inch ratchet and socket.
Correct Answer
B. 1/2 inch speed wrench.Explanation
The correct answer is 1/2 inch speed wrench. The 1/2 inch speed wrench is the tool that can be used to manually initiate cycling ammunition through the universal ammunition system (UALS) replenisher.Rate this question:
-
- 50.
What happens to the unfired rounds returning from the loader when the linked ammunition is being processed?
- A.
Manually separated and counted for the next upload
- B.
Automatically counted and then uploaded back into the loader
- C.
Manually download it through the second gate in the bottom of the replenisher.
- D.
Automatically downloaded through the second gate in the bottom of the replenisher
Correct Answer
D. Automatically downloaded through the second gate in the bottom of the replenisher -
- Acceleration Quizzes
- Acoustic Quizzes
- Chapters Of Physics Quizzes
- Distance Quizzes
- Electrolysis Quizzes
- ESD Quizzes
- Frequency Quizzes
- Light And Reflection Quizzes
- Logic Gate Quizzes
- Magnetic Field Quizzes
- Momentum Quizzes
- Motion Quizzes
- Online Physics Quizzes
- Optics Quizzes
- Physics Of Sound Quizzes
- Practice Physics Quizzes
- Properties Of Matter Quizzes
- Quantum Physics Quizzes
- Reflection Quizzes
- Refraction Quizzes
- Secondary 3 Physics Quizzes
- Sound Quizzes
- Speed Of Light Quizzes
- Thermodynamics Quizzes
- Velocity Quizzes
- Work And Energy Quizzes
Back to top