Quiz Test 3 13/04/2020

21 Questions | Total Attempts: 54

SettingsSettingsSettings
Please wait...
Quiz Test 3 13/04/2020

.


Questions and Answers
  • 1. 
    The maximum width of the scatter shield should be _____ times the width of the chain or belt.
    • A. 

      3

    • B. 

      5

    • C. 

      2

    • D. 

      No such rule

  • 2. 
    DJS Racing decides to put a wing flap on the nose in front of the front axle, its height must be (flaps are located inboard of front tire)
    • A. 

      Lower than 250mm

    • B. 

      Lower than 300mm

    • C. 

      Lower than 500mm

    • D. 

      No such rule

  • 3. 
    Which of the following is/are true?
    • A. 

      The axis of gas cylinder must not point at the driver

    • B. 

      The working gas in the cylinder must be flammable

    • C. 

      The gas cylinder must be insulated from any heat source

    • D. 

      All of the above

  • 4. 
    The bracket shown in figure is used for a bolted joint in the primary structure. Is it rule compliant?
    • A. 

      Yes

    • B. 

      No

  • 5. 
    The LVMS must be mounted in the middle of a completely red circular area of ≥ ­­­­­______ mm radius placed on a high contrast background.
    • A. 

      50

    • B. 

      25

    • C. 

      30

    • D. 

      None of the above

  • 6. 
    Which of the following can be used for vehicle numbering?
    • A. 

      Background Shape – Oval, Spacing – 15mm, Roman Font

    • B. 

      Background Shape – Triangular, Spacing – 20mm, Serif Font

    • C. 

      Background Shape – Square, Spacing – 20mm, Italic

    • D. 

      Background Shape – Rectangular, Spacing – 25mm, Roman Sans-Serif Font

  • 7. 
    A team has two fire extinguishers – one dry powder and one AFFF, each having firefighting agent capacity of 1.1 kg. Is it rule compliant?
    • A. 

      Yes

    • B. 

      No

  • 8. 
    Each team must have a quick jack that lifts up the vehicle such that all driven wheels are ______m off the ground.
  • 9. 
    Team DJS Racing has a steering mounted acceleration paddle. Which of the following is/are true?
    • A. 

      Springs in APPS is not acceptable as return springs

    • B. 

      At least 2 separate sensors must be used as APPS

    • C. 

      If an implausibility occurs between the values of the APPSs and persists for more than 100ms then power to motor must shut down

    • D. 

      No such rule

  • 10. 
    A car with smaller track width (front) of ‘A’ and tire thickness ‘B’ can have rear wing with its span being
    • A. 

      1.25xA – 2xB 

    • B. 

      1.33xA – 2xB

    • C. 

      1.25xA – B

    • D. 

      1.33xA – B

  • 11. 
    The accumulator container can have a base made of the following-
    • A. 

      3.2mm Aluminium

    • B. 

      3.2mm Steel

    • C. 

      5.2mm Aluminium

    • D. 

      2.1mm Steel

    • E. 

      1.2mm Steel

    • F. 

      3.1mm Aluminium

  • 12. 
    The frequency of flashing of TSAL in red colour can be
    • A. 

      2Hz

    • B. 

      3Hz

    • C. 

      4Hz

    • D. 

      5Hz

  • 13. 
    The response value of the device used to monitor insulation between the LVS and the TS if the max TS voltage is 200V is ______ ohm
  • 14. 
    A separate compartment is made for AIRs in an accumulator container. One of the outer walls of the compartment has perforations (5mm dia) allowing air too flow through. Will it clear TI?
    • A. 

      Yes

    • B. 

      No

    • C. 

      Can't Say

  • 15. 
    Which of the following number of master switches and shutdown buttons is allowed?
    • A. 

      1,3

    • B. 

      2,3

    • C. 

      3,1

    • D. 

      3,2

    • E. 

      3,3

  • 16. 
    For an accumulator cell, the data sheet shows that the max cell temp is 72 oC. The max cell temp will be limited to _____ oC for AMS.
  • 17. 
    In side or front view, any part of the TS must not project below
    • A. 

      Lowermost point of vehicle

    • B. 

      Lower surface of chassis

    • C. 

      350mm from ground

    • D. 

      None of these

  • 18. 
    The charger must include a push type emergency stop button which has a minimum diameter of ______ cm.
  • 19. 
    The Ready to Drive sound should have a sound level between [Blank] dBA to [Blank]dBA.
  • 20. 
    The seat mounting points must have a resistance below 0.3 Ω (measured with a current of 1 A) to LVS source.
    • A. 

      True

    • B. 

      False

  • 21. 
    A team uses one master cylinder such that it has 3 ports one for reservoir and other two ports are connected to individual brake lines such that one lines is used for the braking of front calipers and the second separate line is used to brake the rear calipers. Is this rule compliant?
    • A. 

      Yes

    • B. 

      No

    • C. 

      Can't Say

Back to Top Back to top